Study guide
2.1 Branch Circuit Ratings & Conductor Sizing
Michigan Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview & NEC General Requirements
1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements
2 Chapter 2: Branch Circuits & Outlets
2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)
3 Chapter 3: Load Calculations for Services & Feeders
3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations
4 Chapter 4: Wiring Methods, Conductors & Insulation
4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)
5 Chapter 5: Conduit Fill, Box Fill & Panelboards
5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)
6 Chapter 6: Overcurrent Protection Devices & Tap Rules
6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility
7 Chapter 7: Grounding & Bonding Systems
7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers
8 Chapter 8: Motors, Generators & Transformers
8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)
9 Chapter 9: Special Occupancies, Equipment & Conditions
9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)
10 Chapter 10: Michigan Electrical Law, Rules & Code Administration
10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ
11 Chapter 11: Electrical Theory & General Trade Knowledge
11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math
12 Chapter 12: Services & Feeders (Articles 230 & 215)
12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements
13 Chapter 13: Lighting, Appliances & Power-Limited Circuits
13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)
2.1 Branch Circuit Ratings & Conductor Sizing
Key Takeaways Explain This Topic AI
NEC 210.20 requires overcurrent protection devices (OCPD) for branch circuits to be rated at not less than 125% of the continuous load plus 100% of the noncontinuous load.
NEC 210.18 states branch-circuit ratings; in the 2023 NEC the ratings for other than individual branch circuits are 10, 15, 20, 30, 40, and 50 amperes, and a 10-ampere branch circuit is not permitted to supply receptacle outlets.
The NEC's voltage-drop guidance is advisory informational-note material, not an enforceable rule: 3% maximum on branch-circuit conductors and 5% maximum combined across feeder plus branch circuit.
NEC 210.4 requires multiwire branch circuits (MWBC) to have a simultaneous disconnecting means (handle tie or multi-pole breaker) at the panelboard to open all ungrounded conductors simultaneously.
In a multiwire branch circuit, ungrounded conductors must originate from different phase legs to prevent additive neutral current, which would overload the neutral conductor.
Last updated: August 2026
2.1 Branch Circuit Ratings & Conductor Sizing
Branch circuits form the final leg of the electrical distribution system, extending from the last overcurrent protection device (OCPD)—such as a circuit breaker or fuse—to the outlet or connected utilization equipment. Proper sizing of branch circuit conductors and overcurrent devices is a fundamental topic heavily tested on the Michigan Journeyman Electrician Exam. Mastering the rules outlined in NEC Article 210 (Branch Circuits) and Article 310 (Conductors for General Wiring) ensures both system safety and compliance with the 2023 National Electrical Code.
Continuous vs. Noncontinuous Load Sizing Rules
One of the most critical calculations on the licensing exam is determining the minimum rating for branch circuit overcurrent protection devices and conductors based on the nature of the connected load.
Definitions (NEC Article 100)
Continuous Load: A load where the maximum current is expected to continue for 3 hours or more . Examples include commercial office lighting, store window displays, public corridor lighting, and electric space heating.
Noncontinuous Load: A load where the maximum current does not continue for 3 hours. Examples include residential convenience receptacle loads, garbage disposals, and room exhaust fans.
The 125% Rule (NEC 210.19(A) & 210.20(A))
Under NEC 210.20(A) , the overcurrent protection device rating must not be less than the noncontinuous load plus 125 percent of the continuous load: Minimum OCPD Rating = ( Continuous Load × 1.25 ) + Noncontinuous Load \text{Minimum OCPD Rating} = (\text{Continuous Load} \times 1.25) + \text{Noncontinuous Load} Minimum OCPD Rating = ( Continuous Load × 1.25 ) + Noncontinuous Load
Similarly, NEC 210.19(A)(1) requires branch-circuit conductors to have an ampacity before any adjustment or correction factors of not less than the noncontinuous load plus 125% of the continuous load.
Exam Tip: Standard circuit breakers are rated for 80% continuous operation (100% / 1.25 = 80%). Unless the assembly and breaker are explicitly listed for 100% continuous operation (typically limited to specialized commercial equipment rated 400A or higher), you must always apply the 1.25 multiplier to continuous loads.
- Step-by-Step Calculation Examples
- Example 1: Commercial Lighting & Office Receptacles
A 120-volt branch circuit supplies a continuous commercial office lighting load of 16 amperes and a noncontinuous receptacle load of 4 amperes.
- Calculate Continuous Load Portion: 16 A × 1.25 = 20 A 16\text{ A} \times 1.25 = 20\text{ A} 16 A × 1.25 = 20 A
- Add Noncontinuous Load: 20 A + 4 A = 24 A 20\text{ A} + 4\text{ A} = 24\text{ A} 20 A + 4 A = 24 A
Select Overcurrent Device: Per NEC 240.6(A) , standard breaker sizes are 15, 20, 25, 30, 35, 40, 45, 50 amperes. The next standard size rating that equals or exceeds 24A is 25 amperes (or a 25A breaker on #10 AWG copper conductors).
Example 2: Store Window Display
A 120V branch circuit feeds a store window display lighting load of 14 amperes operating for 8 hours daily.
Since the load operates > 3 hours, it is continuous: 14 A × 1.25 = 17.5 A 14\text{ A} \times 1.25 = 17.5\text{ A} 14 A × 1.25 = 17.5 A .
Minimum breaker rating = 20 amperes .
Minimum conductor ampacity = 17.5 amperes , requiring #12 AWG Copper (rated 20A at 60°C/75°C per Table 310.16).
Standard Branch Circuit Ratings
Under NEC 210.18 (the section that carries the branch-circuit Rating rule in the 2023 NEC — it is not 210.3), branch circuits recognized by Article 210 are rated in accordance with the maximum permitted ampere rating or setting of the overcurrent device. In the 2023 edition the ratings for other than individual branch circuits are 10, 15, 20, 30, 40, and 50 amperes .
Important
2023 NEC change — the 10-ampere branch circuit. The 2023 NEC added 10-ampere branch circuits to 210.18 to reflect high-efficiency LED lighting. A 10-ampere branch circuit is permitted to supply lighting outlets, dwelling-unit exhaust fans on a bathroom or laundry lighting circuit, and a gas fireplace unit on an individual branch circuit (210.23(A)). It is not permitted to supply receptacle outlets , fixed appliances (except as permitted for individual branch circuits), garage door openers, or laundry equipment. Older prep material that lists "15, 20, 30, 40, 50" only is written to a pre-2023 code.
- Circuit Rating Permitted Receptacle Rating (NEC Table 210.21(B)(3)) Permitted Load / Application
- 15 Amperes 15A single or duplex receptacles General lighting and dwelling receptacles
20 Amperes 15A or 20A single or duplex receptacles Kitchen small appliances, bathrooms, laundry, general receptacles
- 30 Amperes 30A receptacles only Fixed appliances, heavy-duty lampholders, electric dryers
- 40 Amperes 40A or 50A receptacles Cooking appliances, commercial space heaters
- 50 Amperes 50A receptacles only Heavy cooking equipment, EV chargers, range outlets
- Key Rules for Receptacle Ratings on Multi-Outlet Circuits
On a 15A branch circuit , all receptacles must be rated 15A .
On a 20A branch circuit , receptacles can be rated 15A or 20A (a standard 15A duplex receptacle has a 20A internal feed-through rating).
On a circuit with a single receptacle , the receptacle rating must match the circuit rating (e.g., a single receptacle on a 20A individual branch circuit must be rated 20A per NEC 210.21(B)(1)).
Voltage Drop Recommendations
While the National Electrical Code is primarily a safety standard and voltage drop rules in Article 210 are Informational Notes (not enforceable minimum code mandates), voltage drop questions appear frequently on the Michigan Journeyman Exam.
The NEC Recommendation
Branch-circuit conductors: maximum recommended voltage drop of 3% .
Total combined (feeder + branch circuit): maximum recommended voltage drop of 5% .
These figures live in informational notes , which 90.5(C) makes explanatory and non-enforceable. Because informational-note numbering has shifted between recent code cycles, answer voltage-drop items from the 3%/5% values themselves rather than from a remembered note number.
Single-Phase Voltage Drop Formula V D = 2 × K × I × D C M A VD = \frac{2 \times K \times I \times D}{CMA} V D = CM A 2 × K × I × D % V D = ( V D V s y s t e m ) × 100 \%VD = \left( \frac{VD}{V_{system}} \right) \times 100 % V D = ( V sys t e m V D ) × 100
Where:
K K K = Direct current resistance constant ( 12.9 12.9 12.9 ohms per mil-foot for copper, 21.2 21.2 21.2 for aluminum at 75°C).
I I I = Load current in amperes.
D D D = One-way length of conductor in feet.
C M A CMA CM A = Circular Mil Area of conductor (from NEC Chapter 9, Table 8 ).
Worked Calculation Example
A 120-volt, 16-ampere single-phase continuous load is located 100 feet from the panelboard using #12 AWG THHN copper wire ( C M A = 6 , 530 CMA = 6,530 CM A = 6 , 530 ).
Calculate Voltage Drop: V D = 2 × 12.9 × 16 × 100 6530 = 41280 6530 = 6.32 Volts VD = \frac{2 \times 12.9 \times 16 \times 100}{6530} = \frac{41280}{6530} = 6.32\text{ Volts} V D = 6530 2 × 12.9 × 16 × 100 = 6530 41280 = 6.32 Volts
Calculate Percentage Drop: % V D = 6.32 120 × 100 = 5.27 % \%VD = \frac{6.32}{120} \times 100 = 5.27\% % V D = 120 6.32 × 100 = 5.27%
Evaluation: 5.27 % 5.27\% 5.27% exceeds the recommended 3 % 3\% 3% branch-circuit limit ( 3 % of 120 V = 3.6 V 3\% \text{ of } 120\text{V} = 3.6\text{V} 3% of 120 V = 3.6 V ). To remedy this, sizing up to #10 AWG Copper ( C M A = 10 , 380 CMA = 10,380 CM A = 10 , 380 ) yields V D = 3.97 V VD = 3.97\text{V} V D = 3.97 V ( 3.3 % 3.3\% 3.3% ); sizing up to #8 AWG Copper ( C M A = 16 , 510 CMA = 16,510 CM A = 16 , 510 ) yields V D = 2.5 V VD = 2.5\text{V} V D = 2.5 V ( 2.08 % 2.08\% 2.08% ), satisfying the 3% target.
Multiwire Branch Circuits (MWBC) (NEC 210.4)
A multiwire branch circuit consists of two or more ungrounded (hot) conductors having a voltage potential difference between them, and a grounded (neutral) conductor having equal potential difference between it and each ungrounded conductor.
1. Simultaneous Disconnecting Means (NEC 210.4(B))
Each multiwire branch circuit must be provided with a means to disconnect simultaneously all ungrounded conductors at the point where the branch circuit originates. This requires a multi-pole circuit breaker or single-pole breakers with approved handle ties.
Safety Reason: If an electrician disconnects only one phase of an MWBC to service a circuit, shared neutral current from the remaining live phase can cause lethal electric shock or neutral line degradation.
2. Phase Connection & Neutral Current Sizing
In a single-phase 120/240V multiwire branch circuit, the ungrounded conductors MUST originate from different phase legs (Phase A and Phase B).
Balanced Load: If Line 1 carries 15A and Line 2 carries 15A on opposite phases, the currents cancel in the shared neutral ( I N = 15 A − 15 A = 0 A I_N = 15\text{A} - 15\text{A} = 0\text{A} I N = 15 A − 15 A = 0 A ).
Unbalanced Load: If Line 1 carries 15A and Line 2 carries 9A, the neutral carries the difference ( I N = 15 A − 9 A = 6 A I_N = 15\text{A} - 9\text{A} = 6\text{A} I N = 15 A − 9 A = 6 A ).
DANGER TRAP (Same Phase Error): If both hot wires are connected to the SAME phase (e.g., using a tandem/twin breaker on a single bus space), the currents ADD together ( I N = 15 A + 9 A = 24 A I_N = 15\text{A} + 9\text{A} = 24\text{A} I N = 15 A + 9 A = 24 A ). This will overload a #12 AWG neutral conductor rated for 20A, destroying conductor insulation and creating a major fire risk!
3. Neutral Continuity Rule (NEC 300.13(B))
In multiwire branch circuits, the continuity of a grounded (neutral) conductor shall not depend on device connections such as lamp holders or receptacles. Neutrals must be pigtailed inside every box so that removing a receptacle does not open the neutral path for downstream 120V loads on the opposite phase leg (which would create a 240V series circuit across 120V appliances!).