Study guide
2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11)
Michigan Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview & NEC General Requirements
1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements
2 Chapter 2: Branch Circuits & Outlets
2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)
3 Chapter 3: Load Calculations for Services & Feeders
3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations
4 Chapter 4: Wiring Methods, Conductors & Insulation
4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)
5 Chapter 5: Conduit Fill, Box Fill & Panelboards
5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)
6 Chapter 6: Overcurrent Protection Devices & Tap Rules
6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility
7 Chapter 7: Grounding & Bonding Systems
7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers
8 Chapter 8: Motors, Generators & Transformers
8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)
9 Chapter 9: Special Occupancies, Equipment & Conditions
9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)
10 Chapter 10: Michigan Electrical Law, Rules & Code Administration
10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ
11 Chapter 11: Electrical Theory & General Trade Knowledge
11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math
12 Chapter 12: Services & Feeders (Articles 230 & 215)
12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements
13 Chapter 13: Lighting, Appliances & Power-Limited Circuits
13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)
2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11)
Key Takeaways Explain This Topic AI
NEC 210.52(A)(1) mandates that receptacles in habitable rooms must be installed so that no point along the floor line in any wall space is more than 6 feet measured horizontally from a receptacle outlet (maximum 12-foot spacing between receptacles).
Any wall space 2 feet (600 mm) or more in width (including spaces created by fixed panels or doors) requires a receptacle outlet under NEC 210.52(A)(2).
NEC 210.52(C)(1) requires countertop receptacles in kitchens so that no point along the wall line is more than 24 inches (600 mm) measured horizontally from a receptacle outlet (maximum 48-inch spacing between receptacles).
Under the 2023 NEC revision to 210.52(C)(2), kitchen island and peninsula countertops are no longer strictly required to have receptacles installed, but if receptacles are provided, they must comply with specific mounting rules (cannot be installed below countertop surface unless exception applies).
NEC 210.11(C) mandates specific required branch circuits in dwelling units: at least two 20A small-appliance circuits (210.11(C)(1)), one 20A laundry circuit (210.11(C)(2)), and one 20A bathroom circuit (210.11(C)(3)).
Last updated: August 2026
2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11)
Determining the required location, quantity, and spacing of receptacle outlets in residential construction is one of the most practical skill sets tested on the Michigan Journeyman Electrician exam. NEC Section 210.52 sets forth mandatory placement rules for general wall space, kitchen countertops, bathrooms, and outdoor areas, while NEC Section 210.11(C) mandates dedicated 20-ampere branch circuits for small appliances, laundry facilities, and bathrooms.
General Wall Space Placement Rules (NEC 210.52(A))
In every kitchen, family room, dining room, living room, parlor, library, den, sunroom, bedroom, recreation room, or similar room in dwelling units, receptacle outlets must be installed in accordance with the general wall spacing rules.
The 6-Foot / 12-Foot Rule (NEC 210.52(A)(1))
Receptacles must be installed so that no point measured horizontally along the floor line in any wall space is more than 6 feet (1.8 m) from a receptacle outlet.
Maximum Spacing Between Outlets: 12 feet (3.6 m).
Rationale: Standard household lamp and appliance cords are 6 feet long. This rule guarantees an appliance placed anywhere along a wall can plug into an outlet without using an extension cord.
What Qualifies as "Wall Space"? (NEC 210.52(A)(2))
Any space 2 feet (600 mm) or more in width (including space around corners) unbroken by doorways, fireplaces, floor-to-ceiling windows, or cabinet assemblies.
Wall space occupied by fixed panels in exterior walls (excluding sliding glass door panels).
Wall space created by fixed room dividers, such as free-standing bar counters, railings, or room partitions.
Floor Receptacles (NEC 210.52(A)(3))
Floor receptacles do NOT count toward fulfilling the required wall space outlets unless they are located within 18 inches (450 mm) of the wall.
Kitchen Countertop & Work Surface Rules (NEC 210.52(C))
Countertop receptacles in dwelling unit kitchens and dining areas must be installed to supply portable appliances used on work surfaces.
Wall Countertop Spaces (NEC 210.52(C)(1))
A receptacle outlet must be installed at each wall countertop space that is 12 inches (300 mm) or wider . Receptacles must be placed so that no point along the wall line is more than 24 inches (600 mm) measured horizontally from an outlet (maximum 48-inch spacing between receptacles).
2023 NEC Revision — Island & Peninsula Countertops (NEC 210.52(C)(2))
One of the biggest updates in the 2023 NEC concerns kitchen islands and peninsulas:
Old Code (2020 and prior): Required at least one receptacle for island/peninsula countertops meeting minimum dimensions.
NEC 2023 Rule: Receptacle outlets are NO LONGER MANDATORY on island and peninsula countertops!
If Receptacles ARE Installed (NEC 210.52(C)(3)): They must comply with strict mounting rules:
Mounted on or above the countertop surface (pop-up receptacle assemblies listed for countertop applications, or power poles/towers).
Under-Countertop Mounting Prohibition: Receptacles CANNOT be installed below the countertop surface unless an exception applies (such as for accessibility by persons with disabilities, or where construction prevents top mounting). When permitted below, they cannot extend more than 12 inches below the countertop or be under an overhang exceeding 6 inches.
Exam Trap: Questions asking "What is the minimum number of receptacles required on a kitchen island under the 2023 NEC?" have an answer of ZERO . However, if installed, they must be listed assemblies.
Bathroom & Specific Location Outlets (NEC 210.52(D)-(G))
Location NEC Section Specific Outlet Requirements
Bathrooms 210.52(D) At least one receptacle installed within 3 feet (900 mm) of the outside edge of each basin. Must be located on an adjacent wall or partition.
Outdoor Outlets 210.52(E) At least one receptacle at the front and back of a one-family dwelling (accessible at grade level, max 6.5 ft above grade).
Laundry Area 210.52(F) At least one receptacle outlet for laundry equipment.
Basements & Garages 210.52(G) At least one receptacle outlet in each attached garage, detached garage with electric power, and unfinished basement area.
Mandatory Dwelling Branch Circuits (NEC 210.11(C))
NEC 210.11(C) mandates specific 20-ampere individual and dedicated branch circuits for residential occupancies:
1. Small-Appliance Branch Circuits (NEC 210.11(C)(1))
Quantity: Minimum of TWO 20-ampere small-appliance branch circuits.
Areas Served: Kitchen, pantry, breakfast room, dining room.
Restrictions: These circuits can supply portable countertop appliances and refrigeration equipment. They SHALL NOT supply lighting outlets or ceiling fans!
2. Laundry Branch Circuit (NEC 210.11(C)(2))
Quantity: Minimum of ONE 20-ampere branch circuit.
Areas Served: Receptacle outlet(s) in the laundry area.
Restrictions: This circuit SHALL HAVE NO OTHER OUTLETS (cannot supply lighting or receptacles in adjacent rooms).
3. Bathroom Branch Circuit (NEC 210.11(C)(3))
Quantity: Minimum of ONE 20-ampere branch circuit.
Option A (Multiple Bathrooms): Circuit supplies receptacle outlets in multiple bathrooms. (Cannot supply lighting or exhaust fans!).
Option B (Single Bathroom): Circuit supplies all receptacle, lighting, and exhaust fan outlets in a single bathroom , provided the total connected non-receptacle equipment load does not exceed 50% of the circuit rating (10 amperes).