Study guide

5.3 Box Fill Volume Deductions (NEC 314.16(B))

Michigan Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview & NEC General Requirements

1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements

2 Chapter 2: Branch Circuits & Outlets

2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)

3 Chapter 3: Load Calculations for Services & Feeders

3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations

4 Chapter 4: Wiring Methods, Conductors & Insulation

4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)

5 Chapter 5: Conduit Fill, Box Fill & Panelboards

5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)

6 Chapter 6: Overcurrent Protection Devices & Tap Rules

6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility

7 Chapter 7: Grounding & Bonding Systems

7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers

8 Chapter 8: Motors, Generators & Transformers

8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)

9 Chapter 9: Special Occupancies, Equipment & Conditions

9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)

10 Chapter 10: Michigan Electrical Law, Rules & Code Administration

10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ

11 Chapter 11: Electrical Theory & General Trade Knowledge

11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math

12 Chapter 12: Services & Feeders (Articles 230 & 215)

12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements

13 Chapter 13: Lighting, Appliances & Power-Limited Circuits

13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)

5.3 Box Fill Volume Deductions (NEC 314.16(B))

Key Takeaways Explain This Topic AI

NEC Table 314.16(B) establishes conductor volume allowances: 14 AWG = 2.0 cu in, 12 AWG = 2.25 cu in, 10 AWG = 2.5 cu in, 8 AWG = 3.0 cu in, and 6 AWG = 5.0 cu in.

Each conductor originating outside the box and terminating or spliced inside counts as 1 volume allowance; conductors passing straight through without splice or termination count as 1 volume allowance.

A yoke or strap containing one or more devices (switches, duplex receptacles) counts as a double volume allowance (2×) based on the largest conductor connected to that device (NEC 314.16(B)(4)).

Under the 2023 NEC 314.16(B)(5), equipment grounding conductors count as 1 volume allowance based on the largest EGC for up to 4 EGCs, plus an additional 1/4 (0.25) volume allowance for each additional EGC beyond 4.

Internal cable clamps count as 1 volume allowance based on the largest conductor present in the box; luminaire studs/hickeys count as 1 allowance based on the largest conductor.

Last updated: August 2026

5.3 Box Fill Volume Deductions (NEC 314.16(B))

Exam Focus: Master NEC Table 314.16(B) volume allowances, the 5 deduction categories (Conductors, Clamps, Support Fittings, Devices, EGCs), the 2023 EGC rule change, and complete box fill sizing calculations.

Determining the minimum required box volume requires calculating total volume deductions for all items contained within the enclosure. NEC 314.16(B) outlines the five specific categories of items that require volume allowances. The calculated total required volume must be less than or equal to the total box assembly capacity determined under NEC 314.16(A).

Conductor Volume Allowances (Table 314.16(B))

All volume deductions are based on the cross-sectional volume allowances listed in NEC Table 314.16(B) for each AWG conductor size.

  • Conductor Size (AWG) Volume Allowance per Conductor ( i n 3 in^3 i n 3 )
  • 14 AWG 2.00
  • 12 AWG 2.25
  • 10 AWG 2.50
  • 8 AWG 3.00
  • 6 AWG 5.00
  • The 5 Specific Volume Deduction Categories

NEC 314.16(B)(1) through (B)(5) defines exactly how items inside an outlet or junction box must be counted: THE 5 BOX FILL DEDUCTION CATEGORIES

  • +-------------------------------------------------------------------------+
  • | 1. CONDUCTORS: 1x per insulated wire entering box (passing or spliced) |
  • | 2. CLAMPS: 1x based on largest conductor present (for all clamps) |
  • | 3. FITTINGS: 1x based on largest conductor (per stud/hickey) |
  • | 4. DEVICES: 2x based on largest conductor connected to device strap |
  • | 5. EGCs: 1x up to 4 EGCs + 1/4x for each additional EGC (> 4) |
  • +-------------------------------------------------------------------------+
  • 1. Conductor Fill (NEC 314.16(B)(1))

Entering Conductors: Each insulated conductor originating outside the box and terminating or spliced inside the box counts as 1 volume allowance for its specific AWG size.

Passing Conductors: Each conductor passing straight through the box without splice or termination counts as 1 volume allowance .

Pigtails & Equipment Bonding Jumpers: Conductors that originate and remain entirely within the box (such as pigtails connected to receptacles or wire nuts) count as 0 volume allowances , provided they do not exceed 12 inches in length.

2. Internal Clamp Fill (NEC 314.16(B)(2))

One or more internal cable clamps factory-installed or field-installed inside the box count as 1 single volume allowance , based on the largest conductor present in the box.

Important: No matter how many internal clamps are inside the box (1, 2, or 4), the total clamp deduction is ONLY 1 allowance .

External cable connectors (screwed into box knockouts outside the enclosure) count as 0 allowances .

3. Support Fitting Fill (NEC 314.16(B)(3))

Each luminaire stud or hickey present inside the box counts as 1 single volume allowance , based on the largest conductor present in the box.

4. Device or Equipment Fill (NEC 314.16(B)(4))

Each single strap or yoke containing one or more devices (such as a single receptacle, duplex receptacle, triplex receptacle, single-pole switch, 3-way switch, timer, or GFCI) counts as a DOUBLE volume allowance (2×) .

The 2× deduction is based on the largest conductor connected to the device on that strap.

Warning

Device Counting Rule: A duplex receptacle counts as 2 volume allowances (not 1). A combination switch/receptacle on a single strap counts as 2 volume allowances . If a device is connected using 10 AWG wire, the device deduction is 2 × 2.50 in 3 = 5.00 in 3 2 \times 2.50\text{ in}^3 = 5.00\text{ in}^3 2 × 2.50 in 3 = 5.00 in 3 .

5. Equipment Grounding Conductor (EGC) Fill (NEC 314.16(B)(5)) — 2023 Code Update!

Prior to the 2020/2023 NEC, all bare EGCs counted as 1 single allowance. The 2023 NEC 314.16(B)(5) refined this rule to account for overcrowded multi-gang boxes:

Up to Four (4) EGCs: All equipment grounding conductors entering the box count as 1 volume allowance based on the largest EGC.

More than Four (> 4) EGCs: For each additional EGC beyond four (4), add an additional 1/4 (0.25) volume allowance based on the largest EGC.

Isolated Grounding Conductors (IG EGCs): If a separate isolated equipment grounding conductor enters the box, an additional EGC set allowance applies (1 allowance for up to 4 IG EGCs + 1/4 for each additional IG EGC). 2023 NEC EGC DEDUCTION FORMULA (314.16(B)(5))

  • +-------------------------------------------------------------------------+
  • | 1 to 4 EGCs =============> 1.0 Allowance (based on largest EGC) |
  • | 5 EGCs =============> 1.25 Allowances (1.0 + 0.25) |
  • | 6 EGCs =============> 1.50 Allowances (1.0 + 0.25 + 0.25) |
  • | 7 EGCs =============> 1.75 Allowances (1.0 + 3 x 0.25) |
  • +-------------------------------------------------------------------------+
  • Step-by-Step Worked Box Fill Sizing Calculation

Let's work through a comprehensive exam-style box sizing problem.

Problem Statement:

A flush device box contains the following components:

  • Two (2) 12/2 Type NM-B cables (each cable contains 1 Black, 1 White, 1 bare EGC)
  • One (1) 12/3 Type NM-B cable (contains 1 Black, 1 Red, 1 White, 1 bare EGC)
  • Internal nonmetallic cable clamps
  • One (1) duplex receptacle connected to the 12 AWG circuit conductors

All conductors are 12 AWG copper.

Determine the minimum required box volume in cubic inches and select a suitable standard metal box from Table 314.16(A).

Step 1: Count Insulated Conductors (314.16(B)(1))

12/2 NM-B cables: 2 cables × \times × 2 insulated wires = 4 conductors = 4\text{ conductors} = 4 conductors (12 AWG)

12/3 NM-B cable: 1 cable × \times × 3 insulated wires = 3 conductors = 3\text{ conductors} = 3 conductors (12 AWG)

Total insulated conductors = 4 + 3 = 7 conductors = 4 + 3 = 7\text{ conductors} = 4 + 3 = 7 conductors .

Volume deduction: 7 × 2.25 in 3 = 15.75 in 3 7 \times 2.25\text{ in}^3 = \mathbf{15.75\text{ in}^3} 7 × 2.25 in 3 = 15.75 in 3 .

Step 2: Calculate Internal Clamp Allowance (314.16(B)(2))

Internal clamps present = 1 volume allowance = 1\text{ volume allowance} = 1 volume allowance based on largest conductor (12 AWG).

Volume deduction: 1 × 2.25 in 3 = 2.25 in 3 1 \times 2.25\text{ in}^3 = \mathbf{2.25\text{ in}^3} 1 × 2.25 in 3 = 2.25 in 3 .

Step 3: Calculate Support Fitting Allowance (314.16(B)(3))

No luminaire studs or hickeys present = 0.00 in 3 = \mathbf{0.00\text{ in}^3} = 0.00 in 3 .

Step 4: Calculate Device Allowance (314.16(B)(4))

One duplex receptacle strap = 2 volume allowances = 2\text{ volume allowances} = 2 volume allowances based on largest conductor connected (12 AWG).

Volume deduction: 2 × 2.25 in 3 = 4.50 in 3 2 \times 2.25\text{ in}^3 = \mathbf{4.50\text{ in}^3} 2 × 2.25 in 3 = 4.50 in 3 .

Step 5: Calculate Equipment Grounding Conductor Allowance (314.16(B)(5))

Total bare EGCs: 2 (from 12/2 cables) + 1 + 1 + 1 (from 12/3 cable) = 3 bare EGCs = 3\text{ bare EGCs} = 3 bare EGCs .

Since total EGC count is ≤ 4 \le 4 ≤ 4 , deduction is 1 volume allowance based on 12 AWG.

Volume deduction: 1 × 2.25 in 3 = 2.25 in 3 1 \times 2.25\text{ in}^3 = \mathbf{2.25\text{ in}^3} 1 × 2.25 in 3 = 2.25 in 3 .

Step 6: Sum Total Required Box Volume Total Volume = Conductors + Clamps + Device + EGCs = 15.75 + 2.25 + 4.50 + 2.25 = 24.75 cubic inches \begin{aligned}

  • \text{Total Volume} &= \text{Conductors} + \text{Clamps} + \text{Device} + \text{EGCs} \\
  • &= 15.75 + 2.25 + 4.50 + 2.25 \\
  • &= \mathbf{24.75\text{ cubic inches}}

\end{aligned} Total Volume ​ = Conductors + Clamps + Device + EGCs = 15.75 + 2.25 + 4.50 + 2.25 = 24.75 cubic inches ​

Step 7: Select Standard Box from Table 314.16(A)

4 × 1 − 1 / 2 in 4 \times 1-1/2\text{ in} 4 × 1 − 1/2 in Square Box = 21.0 in 3 = 21.0\text{ in}^3 = 21.0 in 3 (Too small! 21.0 < 24.75 21.0 < 24.75 21.0 < 24.75 )

4 × 2 − 1 / 8 in 4 \times 2-1/8\text{ in} 4 × 2 − 1/8 in Deep Square Box = 30.3 in 3 = 30.3\text{ in}^3 = 30.3 in 3 (Sufficient! 30.3 ≥ 24.75 30.3 \ge 24.75 30.3 ≥ 24.75 )

Alternatively, a 4 × 1 − 1 / 2 in 4 \times 1-1/2\text{ in} 4 × 1 − 1/2 in Square Box ( 21.0 in 3 21.0\text{ in}^3 21.0 in 3 ) with a 4.5 in 3 4.5\text{ in}^3 4.5 in 3 plaster ring ( 21.0 + 4.5 = 25.5 in 3 21.0 + 4.5 = 25.5\text{ in}^3 21.0 + 4.5 = 25.5 in 3 ) is code-compliant.

Calculation Summary Checklist

Item Category Quantity / Rule Deduction Calculation Volume Subtotal

12 AWG Conductors 7 Insulated Wires 7 × 2.25 in 3 7 \times 2.25\text{ in}^3 7 × 2.25 in 3 15.75 in 3 15.75\text{ in}^3 15.75 in 3

Internal Clamps 1 Allowance 1 × 2.25 in 3 1 \times 2.25\text{ in}^3 1 × 2.25 in 3 2.25 in 3 2.25\text{ in}^3 2.25 in 3

Duplex Receptacle 1 Device Strap (2×) 2 × 2.25 in 3 2 \times 2.25\text{ in}^3 2 × 2.25 in 3 4.50 in 3 4.50\text{ in}^3 4.50 in 3

Bare EGCs (3 total) 1 Allowance ( ≤ 4 \le 4 ≤ 4 ) 1 × 2.25 in 3 1 \times 2.25\text{ in}^3 1 × 2.25 in 3 2.25 in 3 2.25\text{ in}^3 2.25 in 3

TOTAL REQUIRED — — 24.75 in 3 24.75\text{ in}^3 24.75 in 3