Study guide

5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)

Michigan Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview & NEC General Requirements

1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements

2 Chapter 2: Branch Circuits & Outlets

2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)

3 Chapter 3: Load Calculations for Services & Feeders

3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations

4 Chapter 4: Wiring Methods, Conductors & Insulation

4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)

5 Chapter 5: Conduit Fill, Box Fill & Panelboards

5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)

6 Chapter 6: Overcurrent Protection Devices & Tap Rules

6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility

7 Chapter 7: Grounding & Bonding Systems

7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers

8 Chapter 8: Motors, Generators & Transformers

8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)

9 Chapter 9: Special Occupancies, Equipment & Conditions

9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)

10 Chapter 10: Michigan Electrical Law, Rules & Code Administration

10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ

11 Chapter 11: Electrical Theory & General Trade Knowledge

11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math

12 Chapter 12: Services & Feeders (Articles 230 & 215)

12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements

13 Chapter 13: Lighting, Appliances & Power-Limited Circuits

13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)

5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)

Key Takeaways Explain This Topic AI

NEC 408.36 requires every panelboard to be individually protected on its supply side by an overcurrent protective device with a rating not exceeding that of the panelboard.

Neutral (grounded) conductors must be bonded to the enclosure at the main service disconnecting means (NEC 250.24), but must remain completely isolated from the enclosure and equipment grounding bus at all subpanels (NEC 250.32).

NEC 408.4 requires every circuit and circuit modification to be legibly identified with its clear, evident, and specific purpose on a circuit directory located on the face or inside door of the panelboard.

Wire bending space within panelboard and switchboard enclosures must comply with NEC 312.6(A) for conductors not entering opposite their terminals and 312.6(B) for conductors entering opposite their terminals.

Panelboard busbar ratings must equal or exceed the feeder or service overcurrent device rating supplying the panel, and ungrounded busbars must be arranged to prevent phase imbalance.

Last updated: August 2026

5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)

Exam Focus: Master NEC Article 408 panelboard overcurrent protection (408.36), neutral bonding vs. isolation rules (250.24 & 250.32), back-fed breaker rules, circuit directories (408.4), and wire bending space (312.6).

NEC Article 408 regulates the installation, overcurrent protection, busbar arrangement, and enclosure requirements for panelboards, switchboards, and switchgear. Panelboards serve as the central distribution nodes of electrical systems, housing circuit breakers or fuses that protect downstream branch circuits and feeders. Electricians must ensure panelboards are correctly rated, properly protected on the supply side, and wired to maintain ground-fault safety.

Panelboard Overcurrent Protection (NEC 408.36)

Overcurrent protection is mandatory to protect the internal busbars and components of a panelboard from severe thermal damage caused by overload or short circuit.

General Rule (NEC 408.36):

Each panelboard must be individually protected on the supply side by an overcurrent protective device (OCPD) having a rating not greater than the rating of the panelboard .

Example: A panelboard rated for 200 Amperes must be protected by a main circuit breaker or feeder fuses rated at 200 Amperes or less . PANELBOARD SUPPLY SIDE PROTECTION (408.36)

  • +-------------------------------------------------------------------------+
  • | Option A: Main Breaker Panelboard | Option B: Main Lug Only (MLO) |
  • | | Subpanel |
  • | [ Feeder Cables ] | [ 100A Feeder Breaker ] |
  • | | | | (In Main Panel) |
  • | [ 200A Main Breaker ] (In Panel) | [ Feeder Conduit ] |
  • | | | | |
  • | [ 200A Panel Busbars ] | [ 100A MLO Panel Busbars ] |
  • +-------------------------------------------------------------------------+

Main Breaker vs. Main Lug Only (MLO) Subpanels:

Main Breaker Panel: Contains an integral main overcurrent breaker mounted inside the panel enclosure.

Main Lug Panel (MLO): Does not contain a main breaker inside the panel itself. This is permitted ONLY IF the feeder conductors supplying the MLO panel are protected on their supply side by an OCPD rated at or below the MLO panelboard rating.

Back-Fed Plug-In Main Circuit Breakers (NEC 408.36(D))

When a plug-in circuit breaker is back-fed to serve as the main disconnect for a panelboard, it MUST be secured in place by an additional fastener (such as a screw, hold-down bracket, or clip).

Purpose: Prevents the main breaker from being accidentally dislodged from the panel busbar while energized, which would create a severe arc flash and shock hazard.

Neutral Busbar Bonding vs. Isolation

One of the most critical safety concepts tested on the journeyman exam is the distinction between service main panel bonding and downstream subpanel neutral isolation .

  • Installation Location Neutral Busbar Status Bonding Screw / MBJ Code Reference
  • Service Disconnecting Means (Main Panel) BONDED to Enclosure INSTALLED NEC 250.24(B)

Downstream Subpanel (Load Center) ISOLATED (Floating) REMOVED / OMITTED NEC 250.32(B) & 408.40 NEUTRAL BONDING VS. ISOLATION ARCHITECTURE

  • +-------------------------------------------------------------------------+
  • | MAIN SERVICE PANEL (250.24) SUBPANEL / LOAD CENTER (250.32) |
  • | +-----------------------------+ +-------------------------------+ |
  • | | Neutral Bus --- Bonded ---> |======>| Neutral Bus --- FLOATING! | |
  • | | | (Green Screw IN) | 4-Wire| (Green Screw REMOVED) | |
  • | | Ground Bus --- Bonded ---> | Feeder| Ground Bus --- Bonded ---> | |
  • | +-----------------------------+ +-------------------------------+ |
  • +-------------------------------------------------------------------------+

Why Must Neutral Busbars Be Floating in Subpanels?

Prevent Parallel Ground Paths: If the neutral busbar were bonded to the metal enclosure in a subpanel, load current returning from 120V circuits would split between the neutral conductor and the equipment grounding conductor (metal conduit / ground wire).

Objectionable Current (NEC 250.6): Neutral current flowing continuously over metal raceways and ground wires creates severe shock hazards, energizes equipment enclosures, and causes electronic noise.

GFCI Tripping: Parallel ground loops cause upstream Ground-Fault Circuit Interrupters (GFCIs) and Ground-Fault Protection of Equipment (GFPE) devices to trip falsely.

Circuit Directory Requirements (NEC 408.4)

Under NEC 408.4(A) , every panelboard and switchboard must feature a clear, legible circuit directory.

Directory Requirements:

Clear & Specific Identification: Every circuit and circuit modification must be legibly identified as to its clear, evident, and specific purpose .

Location: The directory card or label must be permanently affixed to the face or inside of the panel door.

Prohibited Vague Terminology: Descriptions such as "Plugs", "Lights", "Outlets", "Receptacles", "Spares", or "Misc" are STRICTLY CODE VIOLATIONS !

Compliant Examples: "Kitchen Island Receptacles", "Master Bedroom Lighting", "HVAC Condenser Unit #1".

Available Fault Current Marking (NEC 408.4(B)):

In commercial and industrial installations, service panelboards must be field-marked with the maximum available fault current and the date the fault current calculation was performed.

Wire Bending Space within Cabinets (NEC 312.6)

Conductors terminating inside panelboards require adequate physical bending room within the side gutters and top/bottom wireways to prevent conductor stress, insulation cleavage, and terminal block failure. WIRE BENDING SPACE (NEC 312.6)

  • +-------------------------------------------------------------------------+
  • | Cabinet Wall |
  • | | <====== Bending Space (Table 312.6(A)) ======> | Terminal Block |
  • | |-----------------------------\ | |
  • | \--------------------| |
  • | Conductor | |
  • +-------------------------------------------------------------------------+

NEC 312.6(A) vs. 312.6(B):

Table 312.6(A): Applies where conductors do NOT enter or leave the enclosure through the wall directly opposite their terminals (e.g., wire enters top knockout and curves down side gutter to side terminal).

Table 312.6(B): Applies where conductors DO enter or leave the enclosure directly opposite their terminals (requires significantly larger bending depth).

Table 312.6(A) Minimum Wire Bending Space Reference

  • Conductor Size 1 Wire per Terminal 2 Wires per Terminal 3 Wires per Terminal
  • 1/0 AWG 3.5 inches 5.0 inches 7.0 inches
  • 2/0 AWG 3.5 inches 6.0 inches 8.0 inches
  • 3/0 AWG 4.0 inches 6.0 inches 8.0 inches
  • 4/0 AWG 4.5 inches 6.5 inches 8.5 inches
  • 250 kcmil 4.5 inches 6.5 inches 8.5 inches
  • 350 kcmil 5.0 inches 10.0 inches 12.0 inches
  • 500 kcmil 6.0 inches 10.0 inches 12.0 inches
  • High-Leg Delta Phase Arrangement (NEC 408.3(F))

On 3-phase, 4-wire delta-connected systems (120/240V 3-phase 4-wire high-leg delta):

High-Leg Phase Identification: The phase conductor having the higher voltage to ground ( 208 Volts to ground ) must be designated as Phase B .

Orange Identification: Phase B must be durably identified by an orange outer finish , tagging, or tape at all connection points where the neutral is present.

Panelboard Bus Location: In panelboards, the B phase high-leg must occupy the center busbar (B-phase) location.