Study guide
11.2 Alternating Current, Single-Phase & Three-Phase Systems
Michigan Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview & NEC General Requirements
1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements
2 Chapter 2: Branch Circuits & Outlets
2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)
3 Chapter 3: Load Calculations for Services & Feeders
3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations
4 Chapter 4: Wiring Methods, Conductors & Insulation
4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)
5 Chapter 5: Conduit Fill, Box Fill & Panelboards
5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)
6 Chapter 6: Overcurrent Protection Devices & Tap Rules
6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility
7 Chapter 7: Grounding & Bonding Systems
7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers
8 Chapter 8: Motors, Generators & Transformers
8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)
9 Chapter 9: Special Occupancies, Equipment & Conditions
9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)
10 Chapter 10: Michigan Electrical Law, Rules & Code Administration
10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ
11 Chapter 11: Electrical Theory & General Trade Knowledge
11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math
12 Chapter 12: Services & Feeders (Articles 230 & 215)
12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements
13 Chapter 13: Lighting, Appliances & Power-Limited Circuits
13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)
11.2 Alternating Current, Single-Phase & Three-Phase Systems
Key Takeaways Explain This Topic AI
Alternating current in North America reverses at 60 hertz, and the RMS value used in every code calculation is 0.707 times the peak value while the peak is 1.414 times the RMS value.
In a three-phase wye system the line voltage equals 1.732 times the phase voltage while line current equals phase current, which is why a 120-volt phase produces a 208-volt line voltage.
In a three-phase delta system the line voltage equals the phase voltage while line current equals 1.732 times the phase current.
Single-phase apparent power is VA = E x I, and three-phase apparent power is VA = 1.732 x E-line x I-line, so amperage from a three-phase VA total is I = VA / (1.732 x E).
On a 120/240-volt three-phase four-wire delta system the high leg measures approximately 208 volts to the grounded conductor and must be identified in orange or by tagging, and NEC 408.3(F) fixes its position as phase B in the panelboard.
Last updated: August 2026
11.2 Alternating Current, Single-Phase & Three-Phase Systems
Exam Focus: Frequency and RMS values, wye versus delta relationships, the 1.732 factor, converting between VA and amperes on single- and three-phase systems, and high-leg delta identification.
Every commercial load calculation on this examination ends with a division by either 240 (single-phase) or by 1.732 × line voltage (three-phase). Getting the system type right is worth more points than any single table lookup.
Alternating Current Basics
Frequency: North American power alternates at 60 hertz — 60 complete cycles per second, so the current reverses direction 120 times per second.
Period: one cycle takes 1/60 second ≈ 16.67 milliseconds .
RMS (effective) value: the DC-equivalent heating value. Every voltage and current in the NEC is an RMS value unless stated otherwise. E R M S = 0.707 × E P E A K E P E A K = 1.414 × E R M S E_{RMS} = 0.707 \times E_{PEAK} \qquad E_{PEAK} = 1.414 \times E_{RMS} E RMS = 0.707 × E PE A K E PE A K = 1.414 × E RMS
A "120-volt" circuit has a peak of about 170 volts , and a "277-volt" circuit peaks near 392 volts . That matters for insulation ratings and for understanding why a 600-volt-rated conductor is used on a 480-volt system.
Single-Phase Systems
- System Description Common Use
- 120 V, 2-wire One ungrounded conductor and a grounded conductor Lighting and receptacle branch circuits
- 120/240 V, 3-wire Two ungrounded conductors 180° apart plus a grounded center tap Standard dwelling service
On a 120/240 V system, the two ungrounded conductors are 180 degrees out of phase , which is why the voltage between them is the arithmetic sum, 240 V, and why the neutral of a properly connected multiwire branch circuit carries the difference of the two line currents. Single-phase: V A = E × I I = V A E \text{Single-phase: } VA = E \times I \qquad I = \frac{VA}{E} Single-phase: V A = E × I I = E V A
Three-Phase Systems and the 1.732 Factor
Three-phase power uses three ungrounded conductors whose voltages are 120 electrical degrees apart . The constant that connects line values to phase values is 3 = 1.732 \sqrt{3} = 1.732 3 = 1.732 . +-------------------------------------------------------------------------+
- | WYE vs. DELTA — MEMORIZE THIS BOX |
- | |
- | WYE (Y) DELTA |
- | ------------------------------ ------------------------------ |
- | E_line = 1.732 x E_phase E_line = E_phase |
- | I_line = I_phase I_line = 1.732 x I_phase |
- | |
- | Has a neutral point; supplies No neutral unless one corner |
- | line-to-neutral loads. or midpoint is grounded. |
- | |
- | 208Y/120 V, 480Y/277 V 240 V, 480 V, 240/120 high leg |
- +-------------------------------------------------------------------------+
Why 208 Volts?
On a 208Y/120 V system each phase-to-neutral voltage is 120 V. The line-to-line voltage is: E l i n e = 1.732 × 120 = 207.8 ≈ 208 V E_{line} = 1.732 \times 120 = 207.8 \approx 208\ \text{V} E l in e = 1.732 × 120 = 207.8 ≈ 208 V
Likewise 1.732 × 277 = 479.8 ≈ 480 V 1.732 \times 277 = 479.8 \approx 480\ \text{V} 1.732 × 277 = 479.8 ≈ 480 V .
Caution
The two-phases-of-a-wye trap. Two ungrounded conductors of a 208Y/120 V system are 120 degrees apart, not 180 . A 240 V single-phase appliance will not work correctly on 208 V, and a resistance heater on 208 V produces only about 75% of its 240 V output, because power varies with the square of voltage: ( 208 / 240 ) 2 = 0.751 (208/240)^2 = 0.751 ( 208/240 ) 2 = 0.751 .
Three-Phase Power Formulas V A = 1.732 × E l i n e × I l i n e I l i n e = V A 1.732 × E l i n e VA = 1.732 \times E_{line} \times I_{line} \qquad I_{line} = \frac{VA}{1.732 \times E_{line}} V A = 1.732 × E l in e × I l in e I l in e = 1.732 × E l in e V A
Worked Example
A 208Y/120 V three-phase feeder carries a calculated load of 45,000 VA. I = 45,000 1.732 × 208 = 45,000 360.3 = 124.9 A I = \frac{45{,}000}{1.732 \times 208} = \frac{45{,}000}{360.3} = 124.9\ \text{A} I = 1.732 × 208 45 , 000 = 360.3 45 , 000 = 124.9 A
The same 45,000 VA on a 480Y/277 V system draws only: I = 45,000 1.732 × 480 = 45,000 831.4 = 54.1 A I = \frac{45{,}000}{1.732 \times 480} = \frac{45{,}000}{831.4} = 54.1\ \text{A} I = 1.732 × 480 45 , 000 = 831.4 45 , 000 = 54.1 A
That is the engineering reason commercial buildings distribute at 480 V and transform down: at 2.3 times the voltage, the conductor carries 2.3 times less current.
The High-Leg Delta (120/240 V, 3-Phase, 4-Wire)
A four-wire delta system grounds the midpoint of one transformer winding so that two of the three phases give 120 V to ground for lighting, while all three give 240 V line-to-line for motors.
The third phase — the high leg , also called the wild leg or stinger — measures: E h i g h l e g = 1.732 × 120 = 208 V to the grounded conductor E_{high\ leg} = 1.732 \times 120 = 208\ \text{V to the grounded conductor} E hi g h l e g = 1.732 × 120 = 208 V to the grounded conductor
Rule Requirement
Identification The conductor with the higher voltage to ground must be durably and permanently marked by an outer finish that is orange in color , or by other effective means (tagging) at every point where a connection is made if the grounded conductor is also present
Panelboard position (408.3(F)) Where a panelboard is supplied from a 4-wire delta system, the high leg is phase B — the busbar or terminal having the higher voltage to ground is arranged as the B phase
Important
Never land a 120-volt load on the high leg. A 120 V circuit connected between the high leg and the neutral sees 208 V and will destroy the load. Recognizing the 208 V reading on a 240 V delta system is a classic troubleshooting item.
Quick Reference
Need Single-Phase Three-Phase
Amperes from VA I = V A / E I = VA / E I = V A / E I = V A / ( 1.732 × E ) I = VA / (1.732 \times E) I = V A / ( 1.732 × E )
VA from amperes V A = E × I VA = E \times I V A = E × I V A = 1.732 × E × I VA = 1.732 \times E \times I V A = 1.732 × E × I