Study guide

13.1 Luminaires & Lighting Installations (NEC Article 410)

Michigan Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview & NEC General Requirements

1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements

2 Chapter 2: Branch Circuits & Outlets

2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)

3 Chapter 3: Load Calculations for Services & Feeders

3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations

4 Chapter 4: Wiring Methods, Conductors & Insulation

4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)

5 Chapter 5: Conduit Fill, Box Fill & Panelboards

5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)

6 Chapter 6: Overcurrent Protection Devices & Tap Rules

6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility

7 Chapter 7: Grounding & Bonding Systems

7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers

8 Chapter 8: Motors, Generators & Transformers

8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)

9 Chapter 9: Special Occupancies, Equipment & Conditions

9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)

10 Chapter 10: Michigan Electrical Law, Rules & Code Administration

10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ

11 Chapter 11: Electrical Theory & General Trade Knowledge

11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math

12 Chapter 12: Services & Feeders (Articles 230 & 215)

12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements

13 Chapter 13: Lighting, Appliances & Power-Limited Circuits

13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)

13.1 Luminaires & Lighting Installations (NEC Article 410)

Key Takeaways Explain This Topic AI

NEC 410.10(D) prohibits cord-connected luminaires, chain-, cable-, or cord-suspended luminaires, lighting track, pendants, and ceiling-suspended paddle fans within a zone measured 3 feet horizontally and 8 feet vertically from the top of a bathtub rim or shower stall threshold.

NEC 410.16 defines the clothes closet storage space and prohibits incandescent or LED luminaires with open or partially enclosed lamps and pendant luminaires or lampholders in clothes closets.

Clothes closet luminaire clearances under 410.16(C) are 12 inches for surface-mounted incandescent or LED luminaires with completely enclosed light sources, 6 inches for surface-mounted fluorescent luminaires and for recessed incandescent, LED, or fluorescent luminaires, and 0 inches for surface-mounted fluorescent or LED luminaires identified for installation within the storage space.

NEC 314.27(A) requires an outlet box used as the sole support of a luminaire to be designed for the purpose and limits it to a luminaire weighing 50 pounds or less unless the box is listed for the weight to be supported.

NEC 314.27(C) requires outlet boxes used as the sole support of a ceiling-suspended paddle fan to be listed and marked for that use, with the maximum weight supported identified, not exceeding 70 pounds.

Last updated: August 2026

13.1 Luminaires & Lighting Installations (NEC Article 410)

Exam Focus: Wet and damp location listing, the 410.10(D) bathtub and shower zone, the 410.16 clothes closet storage space and its clearance table, recessed luminaire clearances and IC ratings, 314.27 support limits, and luminaire disconnecting means.

Lighting is a named subject on the PSI journeyman blueprint, and the statutory military-affidavit list in MCL 339.5715(1)(b)(x) names "all types and applications of lighting fixtures, ratings, requirements for occupancies, special provisions, and clearances." Article 410 supplies almost all of it.

Listing, Locations, and General Rules

  • Rule Requirement
  • 410.6 Luminaires, lampholders, and retrofit kits must be listed

410.10(A) Luminaires installed in wet or damp locations must be marked "Suitable for Wet Locations" or "Suitable for Damp Locations" as applicable, and installed so water cannot enter or accumulate in wiring compartments, lampholders, or other electrical parts

410.10(B) Luminaires installed in commercial cooking hoods must meet a specific list of conditions including identification for the use and construction that excludes vapors, grease, and moisture

410.11 Luminaires must not be installed in clothes closets, over combustible material , or in similar locations except as permitted

410.30 Luminaires may be used as a raceway only where listed and marked for use as a raceway, or where the assembly is identified for that use

The Bathtub and Shower Zone — NEC 410.10(D)

This is the single most heavily tested clearance in Article 410. +-------------------------------------------------------------------------+

  • | NEC 410.10(D) BATHTUB AND SHOWER ZONE |
  • | |
  • | <----------- 3 ft horizontal -----------> |
  • | ^ +--------------------------------------------------+ |
  • | | | | |
  • | | | PROHIBITED IN THIS ZONE: | |
  • | 8 ft | - Cord-connected luminaires | |
  • | vert. | - Chain-, cable-, or cord-suspended luminaires | |
  • | | | - Lighting track | |
  • | | | - Pendants | |
  • | | | - Ceiling-suspended (paddle) fans | |
  • | v +--------------------------------------------------+ |
  • | ============ top of tub rim / shower threshold ===== |
  • | |
  • | Measured 3 ft HORIZONTALLY and 8 ft VERTICALLY from the TOP of the |
  • | bathtub rim or shower stall threshold. |
  • +-------------------------------------------------------------------------+

Two refinements matter:

Luminaires within the zone that are not of the prohibited types must be listed for damp locations , or listed for wet locations where subject to shower spray.

The 2023 NEC clarified that a ceiling-suspended fan with a luminaire (light kit) is not permitted within the zone. Pair this with 406.9(C) , which prohibits receptacles within a bathtub or shower space.

  • Clothes Closets — NEC 410.16
  • Step 1: Define the Storage Space (410.2 / 410.16(A))

The storage space is the volume bounded by the sides and back closet walls and extending:

from the closet floor vertically to the height of the highest clothes-hanging rod , and

horizontally 24 inches from the sides and back walls (or to the wall, whichever is less), continuing vertically to the higher of the highest rod or 6 ft , and

above that, a 12-inch depth or the shelf width, whichever is greater.

Step 2: Rule Out the Prohibited Types (410.16(B))

Not permitted in a clothes closet:

  • Incandescent or LED luminaires with open or partially enclosed lamps
  • Pendant luminaires or lampholders
  • Step 3: Apply the Clearances (410.16(C))

Minimum clearance between the luminaire and the nearest point of the storage space :

  • Luminaire Type Minimum Clearance
  • Surface-mounted incandescent or LED with completely enclosed light source 12 in (300 mm)
  • Surface-mounted fluorescent 6 in (150 mm)
  • Recessed incandescent or LED with completely enclosed light source 6 in (150 mm)
  • Recessed fluorescent 6 in (150 mm)
  • Surface-mounted fluorescent or LED identified for installation within the storage space 0 in

Caution

Memorize the 12-inch outlier. Only one row in that table is 12 inches: the surface-mounted incandescent or LED with a completely enclosed light source. Everything recessed is 6 inches, and a luminaire specifically identified for installation within the storage space may be installed with no clearance at all.

Recessed Luminaires — NEC 410 Part XII

Rule Requirement

410.115(B) Thermally protected recessed luminaires are required; the thermal protection prevents overheating from lamp over-wattage or insulation

410.116(A)(1) A recessed luminaire not identified for contact with insulation must have at least 1/2 in (13 mm) clearance from combustible materials, except at the points of support

410.116(B) Thermal insulation must not be installed above a recessed luminaire or within 3 in (75 mm) of the enclosure, wiring compartment, ballast, transformer, LED driver, or power supply, unless the luminaire is identified for insulation contact (Type IC)

410.117(C) Tap conductors of a type suitable for the temperature encountered may run from an outlet box to a recessed luminaire, in a suitable raceway or Type AC or MC cable at least 450 mm (18 in) but not more than 1.8 m (6 ft) long

Supporting Luminaires and Fans

Rule Limit

314.27(A)(1) An outlet box used as the sole support of a luminaire must be designed for the purpose ; a luminaire weighing more than 50 lb must be supported independently of the outlet box unless the box is listed and marked for the weight

314.27(C) Outlet boxes used as the sole support of a ceiling-suspended paddle fan must be listed and marked for that use, with the maximum weight supported marked, not exceeding 70 lb

410.36(B) Framing members of suspended ceiling systems may support luminaires where securely fastened and the ceiling system is secured and supported

Important

A standard ceiling box is not a fan box. A round or octagonal box listed for luminaire support is not rated for the dynamic side-to-side load of a paddle fan. The fan-rated box must be listed and marked, and if it supports more than 35 lb it must be marked with the maximum weight up to 70 lb.

Luminaire Disconnecting Means

For fluorescent or LED luminaires that use double-ended lamps and contain ballasts or drivers , and that are installed in indoor locations, a disconnecting means must be provided so the ballast or driver can be serviced without energized parts. It must be accessible to qualified persons before servicing, and may be internal or external to the luminaire.

Exceptions cover luminaires supplied by cord and plug with an accessible separable connector, emergency-circuit luminaires, and locations where the disconnecting means would create a greater hazard.

Lighting Outlets Required — NEC 210.70

Although it lives in Article 210, this rule is asked as a lighting question:

Location Requirement

Dwelling habitable rooms (210.70(A)(1)) At least one wall switch-controlled lighting outlet in every habitable room, kitchen, and bathroom

Dwelling additional locations (210.70(A)(2)) Hallways, stairways, attached garages, detached garages with electric power, and at outdoor entrances or exits with grade-level access

Stairways Where a stairway has 6 or more risers between floor levels, a wall switch is required at each floor level and landing that includes an entryway

Dwelling attics, basements, crawl spaces, utility rooms (210.70(A)(3)) At least one lighting outlet containing a switch or controlled by a wall switch where these spaces are used for storage or contain equipment requiring servicing, located at or near the equipment