Study guide

3.2 Fixed Appliance, Dryer, & Cooking Unit Loads

Michigan Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview & NEC General Requirements

1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements

2 Chapter 2: Branch Circuits & Outlets

2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)

3 Chapter 3: Load Calculations for Services & Feeders

3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations

4 Chapter 4: Wiring Methods, Conductors & Insulation

4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)

5 Chapter 5: Conduit Fill, Box Fill & Panelboards

5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)

6 Chapter 6: Overcurrent Protection Devices & Tap Rules

6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility

7 Chapter 7: Grounding & Bonding Systems

7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers

8 Chapter 8: Motors, Generators & Transformers

8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)

9 Chapter 9: Special Occupancies, Equipment & Conditions

9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)

10 Chapter 10: Michigan Electrical Law, Rules & Code Administration

10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ

11 Chapter 11: Electrical Theory & General Trade Knowledge

11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math

12 Chapter 12: Services & Feeders (Articles 230 & 215)

12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements

13 Chapter 13: Lighting, Appliances & Power-Limited Circuits

13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)

3.2 Fixed Appliance, Dryer, & Cooking Unit Loads

Key Takeaways Explain This Topic AI

Under NEC 220.53, a 75% demand factor can be applied to the total nameplate rating of four or more fixed appliances fastened in place on the same feeder or service in a dwelling unit (excluding ranges, clothes dryers, space heating, and A/C).

Electric clothes dryer loads must be calculated at a minimum of 5,000 VA or the nameplate rating, whichever is larger, with Table 220.54 demand factors applied for multiple units (NEC 220.54).

Household electric ranges rated up to 12 kW use Table 220.55 Column C maximum demand, which specifies an 8 kW demand load for 1 range.

For individual ranges rated over 12 kW, Table 220.55 Note 1 requires adding a 5% demand increase for each additional kW (or major fraction thereof) above 12 kW to the Column C maximum demand.

Last updated: August 2026

3.2 Fixed Appliance, Dryer, & Cooking Unit Loads

Once general lighting and receptacle loads are determined, feeder and service calculations require sizing major residential loads: fixed appliances, electric clothes dryers, and household cooking equipment. Because these heavy electrical loads do not operate at full power simultaneously, NEC Article 220 provides specific demand factors and rules to reduce calculated service demand while ensuring adequate ampacity.

1. Fastened-in-Place Appliance Demand Factor (NEC 220.53)

In a dwelling unit, NEC 220.53 permits a demand factor of 75% (0.75) to be applied to the total nameplate rating of four (4) or more appliances fastened in place that are served by the same feeder or service.

Qualifying vs. Excluded Appliances

To apply the 75% demand factor correctly, you must know which appliances qualify and which are strictly excluded: +-----------------------------------------------------------------------+

  • | NEC 220.53 APPLIANCE COUNT RULES |
  • | |
  • | QUALIFYING APPLIANCES (Count towards 4+): |
  • | - Electric Water Heater |
  • | - Garbage Disposal |
  • | - Dishwasher |
  • | - Trash Compactor |
  • | - Built-in Microwave |
  • | - Attic Exhaust Fan / Sump Pump |
  • | |
  • | EXCLUDED APPLIANCES (Do NOT count towards 4+): |
  • | - Electric Household Cooking Equipment (Ranges, Ovens, Cooktops) |
  • | - Electric Clothes Dryers |
  • | - Space Heating Equipment (Baseboard or Central Heat) |
  • | - Air-Conditioning Equipment |
  • +-----------------------------------------------------------------------+

Exam Trap: If a dwelling has 3 fastened appliances (Water Heater 4,500W, Dishwasher 1,200W, Disposal 900W) plus an electric range and dryer, you CANNOT apply the 75% factor! You must have at least 4 qualifying fastened-in-place appliances before applying 75%.

2. Electric Clothes Dryer Load Sizing (NEC 220.54)

Under NEC 220.54 , the load for household electric clothes dryers in a dwelling unit is calculated based on the following minimum rules:

Minimum Load Rule: The calculated load for each dryer must be 5,000 VA or the nameplate rating, whichever is larger .

Example: A dryer rated 4,200 VA on its nameplate must be calculated at 5,000 VA .

Example: A dryer rated 6,500 VA on its nameplate must be calculated at 6,500 VA .

Demand Factors for Multiple Dryers (NEC Table 220.54):

  • Number of Dryers Demand Factor (%)
  • 1 to 4 100%
  • 5 85%
  • 6 75%
  • 7 65%
  • 8 60%
  • 9 55%
  • 10 50%

11 to 23 47 % − ( 1 % × each dryer over 11 ) 47\% - (1\% \times \text{each dryer over 11}) 47% − ( 1% × each dryer over 11 )

  • 24 to 42 35%
  • 3. Household Electric Ranges & Cooking Appliances (NEC 220.55)

Calculating electric range and cooking appliance loads is one of the most tested subjects on electrical licensing examinations. NEC Table 220.55 allows demand factors for household electric ranges, wall-mounted ovens, counter-mounted cooking units, and other household cooking appliances rated over 1.75 kW 1.75\text{ kW} 1.75 kW .

Table 220.55 Demand Factor Columns Explained

Column A (Ratings less than 3.5 kW 3.5\text{ kW} 3.5 kW ): Applied as a percentage of total nameplate ratings.

Column B (Ratings 3.5 kW 3.5\text{ kW} 3.5 kW to 8.75 kW 8.75\text{ kW} 8.75 kW ): Applied as a percentage of total nameplate ratings.

Column C (Ratings 8.75 kW 8.75\text{ kW} 8.75 kW to 12 kW 12\text{ kW} 12 kW ): Specifies a maximum demand load in kW directly, rather than a percentage!

Key Values from Table 220.55 (Column C)

  • Number of Appliances Column C Maximum Demand (kW) Rating Range
  • 1 Range 8 kW (8,000 VA) For ranges rated up to 12 kW
  • 2 Ranges 11 kW (11,000 VA) For ranges rated up to 12 kW
  • 3 Ranges 14 kW (14,000 VA) For ranges rated up to 12 kW
  • 4 Ranges 17 kW (17,000 VA) For ranges rated up to 12 kW
  • 5 Ranges 20 kW (20,000 VA) For ranges rated up to 12 kW
  • 4. Range Rating Adjustments Over 12 kW (Table 220.55 Note 1)

When individual ranges exceed 12 kW 12\text{ kW} 12 kW , Note 1 of Table 220.55 requires an increase to the Column C maximum demand value:

Determine the amount by which the range rating exceeds 12 kW 12\text{ kW} 12 kW .

For each additional kW or major fraction thereof ( 0.5 kW 0.5\text{ kW} 0.5 kW or greater) , increase the Column C maximum demand value by 5% (0.05) .

Multiply the Column C demand by ( 1 + Percentage Increase ) (1 + \text{Percentage Increase}) ( 1 + Percentage Increase ) .

Formula for Ranges Over 12 kW: Excess kW = Nameplate Rating (kW) − 12 kW \text{Excess kW} = \text{Nameplate Rating (kW)} - 12\text{ kW} Excess kW = Nameplate Rating (kW) − 12 kW Multiplier = 1 + ( Rounded Excess kW × 0.05 ) \text{Multiplier} = 1 + (\text{Rounded Excess kW} \times 0.05) Multiplier = 1 + ( Rounded Excess kW × 0.05 ) Final Feeder Demand Load = Column C Base Demand × Multiplier \text{Final Feeder Demand Load} = \text{Column C Base Demand} \times \text{Multiplier} Final Feeder Demand Load = Column C Base Demand × Multiplier

  • 5. Step-by-Step Worked Calculation Examples
  • Example 1: Fastened Appliance Load Calculation

A single-family dwelling contains the following fixed appliances connected to the service:

  • Electric Water Heater: 4 , 500 VA 4,500\text{ VA} 4 , 500 VA
  • Dishwasher: 1 , 400 VA 1,400\text{ VA} 1 , 400 VA
  • Garbage Disposal: 900 VA 900\text{ VA} 900 VA
  • Trash Compactor: 1 , 000 VA 1,000\text{ VA} 1 , 000 VA
  • Attic Fan: 600 VA 600\text{ VA} 600 VA

Solution:

Count qualifying appliances: There are 5 qualifying fastened appliances (exceeds the minimum of 4).

Total Nameplate Sum: 4 , 500 + 1 , 400 + 900 + 1 , 000 + 600 = 8 , 400 VA 4,500 + 1,400 + 900 + 1,000 + 600 = 8,400\text{ VA} 4 , 500 + 1 , 400 + 900 + 1 , 000 + 600 = 8 , 400 VA

Apply NEC 220.53 Demand Factor ( 75 % 75\% 75% ): Feeder Demand Load = 8 , 400 VA × 0.75 = 6 , 300 VA \text{Feeder Demand Load} = 8,400\text{ VA} \times 0.75 = \mathbf{6,300\text{ VA}} Feeder Demand Load = 8 , 400 VA × 0.75 = 6 , 300 VA

Example 2: Range Load Calculation ( 15.4 kW 15.4\text{ kW} 15.4 kW Range)

Calculate the feeder demand load for a single household range with a nameplate rating of 15.4 kW 15.4\text{ kW} 15.4 kW .

Solution:

Find Base Column C Demand for 1 range: 8 kW 8\text{ kW} 8 kW .

Determine Excess over 12 kW 12\text{ kW} 12 kW : 15.4 kW − 12 kW = 3.4 kW 15.4\text{ kW} - 12\text{ kW} = 3.4\text{ kW} 15.4 kW − 12 kW = 3.4 kW

Apply Major Fraction Rule: 3.4 kW 3.4\text{ kW} 3.4 kW rounds down to 3 kW 3\text{ kW} 3 kW (since 0.4 0.4 0.4 is less than 0.5 0.5 0.5 ).

Calculate Percentage Increase: 3 kW × 5 % = 15 % increase 3\text{ kW} \times 5\% = 15\%\text{ increase} 3 kW × 5% = 15% increase

Compute Final Demanded Load: Feeder Demand = 8 kW × ( 1 + 0.15 ) = 8 kW × 1.15 = 9.2 kW ( 9 , 200 VA ) \text{Feeder Demand} = 8\text{ kW} \times (1 + 0.15) = 8\text{ kW} \times 1.15 = \mathbf{9.2\text{ kW} (9,200\text{ VA})} Feeder Demand = 8 kW × ( 1 + 0.15 ) = 8 kW × 1.15 = 9.2 kW ( 9 , 200 VA )

6. Branch Circuit Sizing for Cooking Equipment (NEC 210.19(A)(3))

Under NEC 210.19(A)(3) , the branch-circuit rating for a single household range rated 8.75 kW 8.75\text{ kW} 8.75 kW or more must not be less than 40 amperes . Calculated Current = 8 , 000 VA 240 V = 33.33 Amperes \text{Calculated Current} = \frac{8,000\text{ VA}}{240\text{ V}} = 33.33\text{ Amperes} Calculated Current = 240 V 8 , 000 VA ​ = 33.33 Amperes

Since 33.33 A 33.33\text{ A} 33.33 A exceeds 30 A 30\text{ A} 30 A , the circuit must be protected by a minimum 40-ampere overcurrent device using minimum #8 AWG copper conductors .