Study guide

3.1 General Lighting & Receptacle Load Calculations

Michigan Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview & NEC General Requirements

1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements

2 Chapter 2: Branch Circuits & Outlets

2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)

3 Chapter 3: Load Calculations for Services & Feeders

3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations

4 Chapter 4: Wiring Methods, Conductors & Insulation

4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)

5 Chapter 5: Conduit Fill, Box Fill & Panelboards

5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)

6 Chapter 6: Overcurrent Protection Devices & Tap Rules

6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility

7 Chapter 7: Grounding & Bonding Systems

7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers

8 Chapter 8: Motors, Generators & Transformers

8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)

9 Chapter 9: Special Occupancies, Equipment & Conditions

9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)

10 Chapter 10: Michigan Electrical Law, Rules & Code Administration

10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ

11 Chapter 11: Electrical Theory & General Trade Knowledge

11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math

12 Chapter 12: Services & Feeders (Articles 230 & 215)

12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements

13 Chapter 13: Lighting, Appliances & Power-Limited Circuits

13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)

3.1 General Lighting & Receptacle Load Calculations

Key Takeaways Explain This Topic AI

In the 2023 NEC, the dwelling-unit minimum unit load is stated in 220.41 at 3 VA per square foot, and that single figure covers general lighting outlets and all general-use receptacle outlets of 20 amperes or less, so no additional per-receptacle load is added in a dwelling.

Article 220 was reorganized for the 2023 NEC: floor area moved from 220.11 to 220.5(C), non-dwelling lighting moved from 220.12 to 220.42 with Table 220.42(A), the general-lighting demand factors moved from Table 220.42 to Table 220.45, and non-dwelling receptacle demand moved from 220.44 to 220.47.

Under 2023 NEC 220.5(C) the dwelling floor area is taken from outside dimensions and excludes only open porches and unfinished areas not adaptable for future use as a habitable room or occupiable space — attached garages are now INCLUDED, a change from the 2020 NEC.

Non-dwelling general receptacle outlets are calculated at a minimum of 180 VA per single or multiple receptacle on one strap or yoke under NEC 220.14(I).

Table 220.45 applies demand factors to the dwelling-unit general lighting and small-appliance load: 100% of the first 3,000 VA, 35% from 3,001 VA to 120,000 VA, and 25% of the portion above 120,000 VA.

Last updated: August 2026

3.1 General Lighting & Receptacle Load Calculations

Calculating branch circuit, feeder, and service loads is one of the most vital responsibilities of a licensed electrician and a heavily weighted domain on the Michigan Journeyman Electrician exam. Article 220 of the National Electrical Code (NEC 2023) sets forth the precise rules, tables, and formulas required to determine the minimum electrical capacity needed to safely supply a building. The calculation process begins by determining the general lighting load based on building occupancy, floor square footage, and general-purpose receptacle outlets.

Important

Article 220 was renumbered in the 2023 NEC. Michigan tests to the 2023 edition, so the section numbers you memorized from an older book will not match the exam. Learn this crosswalk:

  • Rule 2020 NEC 2023 NEC
  • Floor area 220.11 220.5(C)
  • Dwelling minimum unit load (3 VA/ft²) 220.12 / Table 220.12 220.41
  • Non-dwelling lighting unit loads 220.12 / Table 220.12 220.42 / Table 220.42(A)
  • General lighting demand factors 220.42 / Table 220.42 220.45 / Table 220.45
  • Non-dwelling receptacle demand 220.44 / Table 220.44 220.47
  • 1. Building Floor Area Measurement Rules (NEC 220.5(C))

Before applying unit loads, determine the floor area. Under NEC 220.5(C) , the floor area for each floor is calculated from the outside dimensions of the building, dwelling unit, or other area involved. For dwelling units, the calculated floor area shall not include open porches or unfinished areas not adaptable for future use as a habitable room or occupiable space .

Included vs. Excluded Building Areas

  • Area Type Calculation Status Reason
  • Finished living areas INCLUDED Measured from outside dimensions

Attached garage INCLUDED (2023 change) Garages were dropped from the exclusion list; they carry lighting and receptacle load

  • Unfinished basement or attic adaptable for future habitable use INCLUDED Adaptable space counts
  • Unfinished area NOT adaptable for future habitable or occupiable use EXCLUDED Express exclusion in 220.5(C)
  • Open exterior porch EXCLUDED Express exclusion in 220.5(C)

Caution

The single most common stale answer on this topic. Through the 2020 NEC the dwelling floor area excluded "open porches, garages, or unused or unfinished spaces not adaptable for future use." The 2023 NEC removed garages from that list. On a 2023-based exam, a 30 ft × 50 ft house with a 20 ft × 20 ft attached garage and a 10 ft × 15 ft open porch has a calculated floor area of 1,500 + 400 = 1,900 sq ft , not 1,500 sq ft. (The 2026 NEC re-excludes detached garages, but Michigan enforces the 2023 edition.)

2. Unit Lighting Loads — Two Different Rules

The 2023 NEC splits this topic in two. Dwellings are handled by 220.41; everything else is handled by 220.42 and Table 220.42(A).

Dwelling Units — NEC 220.41

In one-family, two-family, and multifamily dwellings the minimum unit load is 3 volt-amperes per square foot . That single figure covers, and no additional calculation is required for:

all general-use receptacle outlets of 20-ampere rating or less, including receptacles on the circuits required by 210.11(C)(3) (bathroom) and 210.11(C)(4) (garage);

the receptacle outlets required by 210.52(E) (outdoor) and 210.52(G) (basements, garages, accessory buildings);

the lighting outlets required by 210.70.

Code Rule Note: Never add 180 VA per receptacle yoke for dwelling-unit living areas. The 3 VA/ft² already contains them. Adding both is double counting and is a deliberate distractor on licensing exams.

Non-Dwelling Occupancies — NEC 220.42 and Table 220.42(A)

For non-dwelling occupancies, multiply the 220.5(C) floor area by the unit load listed in Table 220.42(A) for that occupancy type. Motors rated less than 1/8 hp connected to a lighting circuit are treated as general lighting load.

Two facts about this table matter more than any single value:

The table was rebuilt. Beginning with the 2020 NEC, the old occupancy list (banks 3.5, offices 3.5, stores 3, warehouses 0.25, and so on) was replaced with values derived from ASHRAE 90.1 lighting power densities. Retail occupancies, for example, are now 1.9 VA/ft² , and notes below the table redirect several old entries — stores and barber shops to retail, banks to office-type occupancies, armories and auditoriums to gymnasium-type occupancies, lodge rooms to hotels and motels, commercial storage garages to parking-garage occupancies, clubs to restaurants.

The 125% continuous-load multiplier is already included. A note to the table states that the 125% multiplier required by 210.20(A) for a continuous load is built into the tabulated unit loads. Applying 1.25 again to a Table 220.42(A) lighting result over-sizes the service and is wrong.

Important

Open the book, do not recite the table. Because these values changed wholesale and the notes redirect occupancies, the reliable exam technique is to turn to Table 220.42(A), read the note letters, and take the number off the page. This is exactly the kind of item the open-book format is designed to test.

220.42(B) Energy Code Alternative

Where a building is designed and constructed to an energy code adopted by the local authority, 220.42(B) permits the lighting load to be calculated using the energy-code unit values, provided a power monitoring system continuously reports the total general lighting load and is set with alarm values that alert the owner or manager if the load exceeds the energy-code value.

3. General Receptacle Load Sizing (NEC 220.14)

For non-dwelling occupancies, general receptacle loads are calculated separately from lighting unless specifically included in Table 220.12 notes (such as the optional office/bank method under NEC 220.14(J)).

The 180 VA Receptacle Yoke Rule (NEC 220.14(I))

Under NEC 220.14(I) , each single or multiple receptacle installed on one single strap (yoke) is calculated at a minimum of 180 volt-amperes (VA) :

  • Single Receptacle (one contact device on a strap) = 180 VA
  • Duplex Receptacle (two contact devices on one strap/yoke) = 180 VA
  • Triplex Receptacle (three contact devices on one strap/yoke) = 180 VA

Quadruplex Receptacle (Quad) on a single mounting strap/yoke = 360 VA (calculated as 2 sets of double receptacles on separate mounting straps, or per NEC 220.14(I) where a single assembly containing 4 or more receptacles is rated at not less than 90 VA per receptacle, i.e., 4 × 90 = 360 VA 4 \times 90 = 360\text{ VA} 4 × 90 = 360 VA ). +-----------------------------------------------------------------------+

  • | RECEPTACLE LOAD RATING SUMMARY |
  • | |
  • | [ Single Receptacle ] ---> 1 Strap ---> 180 VA |
  • | [ Duplex Receptacle ] ---> 1 Strap ---> 180 VA |
  • | [ Quad Receptacle ] ---> 2 Straps ---> 360 VA (2 x 180 VA) |
  • +-----------------------------------------------------------------------+
  • Multi-Outlet Assemblies (NEC 220.14(H))

For multi-outlet plug-in assemblies (such as surface raceway with integral outlets):

Standard Duty: Calculate 180 VA for each 5 ft (or fraction thereof) of continuous assembly where appliances are unlikely to be used simultaneously.

Heavy Duty / Simultaneous Use: Calculate 180 VA for each 1 ft (or fraction thereof) where appliances or equipment are expected to operate simultaneously (e.g., electronic repair benches, testing labs).

4. General Lighting Demand Factors (NEC 220.45 / Table 220.45)

Because all lights and general convenience outlets in a building are rarely energized simultaneously at full capacity, NEC 220.45 allows the demand factors of Table 220.45 to be applied to that portion of the total branch-circuit load calculated for general illumination when sizing feeders and service-entrance conductors. They are not applied when determining the number of branch circuits for general illumination.

NEC Table 220.45 Demand Factor Schedule

  • Type of Occupancy Portion of General Lighting Load (VA) Demand Factor (%)
  • Dwelling Units First 3,000 VA or less 100%
  • From 3,001 VA to 120,000 VA 35%
  • Remainder over 120,000 VA 25%
  • Hospitals First 50,000 VA or less 40%
  • Remainder over 50,000 VA 20%
  • Hotels and Motels First 20,000 VA or less 50%
  • From 20,001 VA to 100,000 VA 40%
  • Remainder over 100,000 VA 30%
  • Warehouses (Storage) First 12,500 VA or less 100%
  • Remainder over 12,500 VA 50%
  • All Others (Offices, Stores, etc.) Total calculated VA 100%

Crucial Exam Distinction: Notice that Commercial Offices and Stores have a 100% demand factor under Table 220.42! You CANNOT reduce commercial general lighting feeder loads using the dwelling unit demand steps.

  • 5. Step-by-Step Worked Calculation Example
  • Problem Statement

Calculate the net general lighting and small appliance demand load for a single-family dwelling measuring 45 ft × 60 ft (outside dimensions) with a finished layout, containing the required two 20-amp small appliance branch circuits and one 20-amp laundry branch circuit .

Step 1: Calculate Floor Area Floor Area = 45 ft × 60 ft = 2 , 700 sq ft \text{Floor Area} = 45\text{ ft} \times 60\text{ ft} = 2,700\text{ sq ft} Floor Area = 45 ft × 60 ft = 2 , 700 sq ft

Step 2: Calculate the Minimum Unit Load (NEC 220.41) General Load = 2 , 700 sq ft × 3.0 VA/sq ft = 8 , 100 VA \text{General Load} = 2,700\text{ sq ft} \times 3.0\text{ VA/sq ft} = 8,100\text{ VA} General Load = 2 , 700 sq ft × 3.0 VA/sq ft = 8 , 100 VA

Step 3: Add Small Appliance & Laundry Branch Circuits (NEC 220.52)

Each small appliance circuit and laundry circuit is rated at 1,500 VA minimum:

2 Small Appliance Circuits: 2 × 1 , 500 VA = 3 , 000 VA 2 \times 1,500\text{ VA} = 3,000\text{ VA} 2 × 1 , 500 VA = 3 , 000 VA

1 Laundry Circuit: 1 × 1 , 500 VA = 1 , 500 VA 1 \times 1,500\text{ VA} = 1,500\text{ VA} 1 × 1 , 500 VA = 1 , 500 VA Total General Load before Demand = 8 , 100 VA + 3 , 000 VA + 1 , 500 VA = 12 , 600 VA \text{Total General Load before Demand} = 8,100\text{ VA} + 3,000\text{ VA} + 1,500\text{ VA} = 12,600\text{ VA} Total General Load before Demand = 8 , 100 VA + 3 , 000 VA + 1 , 500 VA = 12 , 600 VA

Step 4: Apply NEC Table 220.45 Demand Factors

Break down the 12,600 VA total load according to Table 220.45 brackets:

First 3,000 VA at 100%: 3 , 000 VA × 1.00 = 3 , 000 VA 3,000\text{ VA} \times 1.00 = 3,000\text{ VA} 3 , 000 VA × 1.00 = 3 , 000 VA

Remaining Load (12,600 VA - 3,000 VA = 9,600 VA) at 35%: 9 , 600 VA × 0.35 = 3 , 360 VA 9,600\text{ VA} \times 0.35 = 3,360\text{ VA} 9 , 600 VA × 0.35 = 3 , 360 VA

Combine Demanded Volt-Amperes: Net General Demand Load = 3 , 000 VA + 3 , 360 VA = 6 , 360 VA \text{Net General Demand Load} = 3,000\text{ VA} + 3,360\text{ VA} = \mathbf{6,360\text{ VA}} Net General Demand Load = 3 , 000 VA + 3 , 360 VA = 6 , 360 VA

6. Common Exam Traps & Calculation Pitfalls

Adding 180 VA for Dwelling Receptacles: Never add 180 VA per receptacle yoke for dwelling unit general living areas. General receptacles are already covered by the 3.0 VA/sq ft 3.0\text{ VA/sq ft} 3.0 VA/sq ft figure.

Omitting Small Appliance and Laundry Circuits: Remember that NEC 220.52 requires adding small appliance ( 3 , 000 VA 3,000\text{ VA} 3 , 000 VA ) and laundry ( 1 , 500 VA 1,500\text{ VA} 1 , 500 VA ) loads to the general lighting load BEFORE applying the Table 220.45 demand factors under the Standard Calculation Method.

Misreading Commercial Receptacle Yokes: A duplex receptacle on a single mounting strap counts as 180 VA , not 2 × 180 = 360 VA 2 \times 180 = 360\text{ VA} 2 × 180 = 360 VA . A quad receptacle on two separate straps counts as 360 VA .