Study guide

8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430)

Michigan Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Exam Overview & NEC General Requirements

1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements

2 Chapter 2: Branch Circuits & Outlets

2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)

3 Chapter 3: Load Calculations for Services & Feeders

3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations

4 Chapter 4: Wiring Methods, Conductors & Insulation

4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)

5 Chapter 5: Conduit Fill, Box Fill & Panelboards

5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)

6 Chapter 6: Overcurrent Protection Devices & Tap Rules

6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility

7 Chapter 7: Grounding & Bonding Systems

7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers

8 Chapter 8: Motors, Generators & Transformers

8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)

9 Chapter 9: Special Occupancies, Equipment & Conditions

9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)

10 Chapter 10: Michigan Electrical Law, Rules & Code Administration

10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ

11 Chapter 11: Electrical Theory & General Trade Knowledge

11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math

12 Chapter 12: Services & Feeders (Articles 230 & 215)

12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements

13 Chapter 13: Lighting, Appliances & Power-Limited Circuits

13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)

8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430)

Key Takeaways Explain This Topic AI

NEC Article 430.6(A)(1) mandates using NEC Tables 430.247 (DC), 430.248 (1-Phase AC), and 430.250 (3-Phase AC) for conductor and overcurrent protection sizing, NOT the motor nameplate rating.

Motor nameplate current is used ONLY for sizing motor overload protection devices in accordance with NEC 430.6(A)(1) and Part III.

Branch-circuit conductors supplying a single continuous-duty motor must have an ampacity of not less than 125% of the motor's NEC Table full-load current (NEC 430.22).

Feeder conductors supplying multiple motors must be sized at 125% of the highest rated motor Table FLA plus 100% of the Table FLAs of all other motors on the feeder, plus non-motor loads (NEC 430.24).

Determining the 'largest motor' for feeder sizing is strictly based on the highest NEC Table full-load current in amperes, not necessarily the highest horsepower rating.

Last updated: August 2026

8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430)

Exam Focus: NEC Table FLA vs. Nameplate FLA (430.6(A)(1)), Single motor branch-circuit conductor sizing at 125% (430.22), Multi-motor feeder conductor sizing (430.24), and terminal temperature ampacity selection (110.14(C)).

Motor circuits present unique electrical challenges due to high starting inrush currents (locked-rotor current) and sustained inductive mechanical loads. Consequently, NEC Article 430 establishes specialized rules that depart significantly from standard general branch-circuit sizing principles. Understanding how to navigate Article 430 tables and calculation rules is one of the highest-yield topics on the Michigan PSI Journeyman Electrician examination.

NEC Table Full-Load Current (FLA) vs. Nameplate Current

One of the most frequent traps on the journeyman exam involves selecting the correct motor current value for circuit calculations. NEC 430.6(A)(1) mandates a strict division between when to use NEC Table values and when to use Motor Nameplate values . +---------------------------------------------------------------------------------+

  • | NEC 430.6(A)(1) CURRENT SELECTION RULE |
  • +---------------------------------------------------------------------------------+
  • | USE NEC TABLES (430.247, 430.248, 430.250) FOR: |
  • | 1. Branch-Circuit Conductor Sizing (430.22) |
  • | 2. Feeder Conductor Sizing (430.24) |
  • | 3. Short-Circuit & Ground-Fault Protection Sizing (430.52 & 430.62) |
  • | 4. Disconnecting Means Ampacity Rating (430.110) |
  • | |
  • | USE MOTOR NAMEPLATE RATING ONLY FOR: |
  • | 1. Motor Overload Relay / Thermal Unit Sizing (430.32 & Part III) |
  • | 2. Separate overload protection devices |
  • +---------------------------------------------------------------------------------+

Mandatory NEC Tables:

Table 430.247: Direct-Current Motors (FLA for 90V, 120V, 180V, 240V, 500V, 600V DC).

Table 430.248: Single-Phase AC Motors (FLA for 115V, 200V, 208V, 230V AC).

Table 430.250: Three-Phase AC Motors (FLA for 115V, 200V, 208V, 230V, 460V, 575V, 2300V AC).

Why Use NEC Tables Instead of Nameplate?

Motor nameplate ratings vary based on manufacturer efficiency and construction quality. If a motor fails and is replaced by a less efficient motor of the same horsepower, the replacement motor will draw more full-load current. Using NEC Table values ensures that branch-circuit conductors and conduit are sized conservatively for worst-case standard motor replacements.

Warning

Exam Trap: A question may state: 'A 230V, single-phase, 5 HP motor has a nameplate rating of 24 Amperes. What is the minimum branch-circuit conductor ampacity?' Ignore the 24A nameplate rating! Turn to NEC Table 430.248, locate 5 HP at 230V (28 Amperes), and multiply 28 A by 125% = 35 Amperes.

Single Motor Branch-Circuit Conductor Sizing (NEC 430.22)

Under NEC 430.22 , conductors supplying a single motor used in a continuous-duty application shall have an ampacity of not less than 125% of the motor full-load current rating determined from the applicable NEC Table. Minimum Conductor Ampacity = NEC Table FLA × 1.25 \text{Minimum Conductor Ampacity} = \text{NEC Table FLA} \times 1.25 Minimum Conductor Ampacity = NEC Table FLA × 1.25

Terminal Temperature Limitations (NEC 110.14(C))

Once the minimum required ampacity is calculated, select the conductor size from NEC Table 310.16 enforcing terminal temperature limits:

Equipment rated 100 Amperes or less (or for #14 AWG through #1 AWG conductors) is generally restricted to the 60°C column rating, unless terminals are explicitly listed for 75°C.

Equipment rated over 100 Amperes (or for conductors larger than #1 AWG) permits using the 75°C column rating.

THHN insulation (90°C rated) is commonly used in practice, but its ampacity must be taken from the 60°C or 75°C column to match terminal ratings, unless performing derating calculations for ambient temperature or conduit bundle fill.

Worked Calculation Example 1: Single Motor Branch Circuit

Question: A 10 HP, 230-Volt, single-phase continuous-duty AC induction motor is installed in a commercial facility. Terminals are rated for 75°C. What is the minimum size THHN copper conductor required for the branch circuit?

Step 1: Determine the Table FLA. Turn to NEC Table 430.248 (Single-Phase AC Motors).

Locate 10 HP under the 230V column → \rightarrow → 50 Amperes .

Step 2: Calculate Minimum Required Ampacity (NEC 430.22). Required Ampacity = 50 A × 1.25 = 62.5 Amperes \text{Required Ampacity} = 50\text{ A} \times 1.25 = 62.5\text{ Amperes} Required Ampacity = 50 A × 1.25 = 62.5 Amperes

Step 3: Select Conductor Size from Table 310.16. Look in the 75°C Copper column of Table 310.16:

  • #8 AWG Cu = 50 A (too small)
  • #6 AWG Cu = 65 A (meets or exceeds 62.5 A)

Answer: #6 AWG THHN Copper .

Multi-Motor Feeder Conductor Sizing (NEC 430.24)

When a single feeder supplies a group of motors, NEC 430.24 dictates that the feeder conductors must have an ampacity sufficient to supply the largest motor load plus the sum of all other motor loads, plus any non-motor continuous and non-continuous loads. Feeder Ampacity = ( 1.25 × FLA largest motor ) + s u m FLA other motors + ( 1.25 × Non-Motor Continuous ) + Non-Motor Non-Continuous \text{Feeder Ampacity} = (1.25 \times \text{FLA}_{\text{largest motor}}) + sum \text{FLA}_{\text{other motors}} + (1.25 \times \text{Non-Motor Continuous}) + \text{Non-Motor Non-Continuous} Feeder Ampacity = ( 1.25 × FLA largest motor ​ ) + s u m FLA other motors ​ + ( 1.25 × Non-Motor Continuous ) + Non-Motor Non-Continuous +-------------------------------------------------------------------------+

  • | MULTI-MOTOR FEEDER CONDUCTOR CALCULATION |
  • | |
  • | [Motor 1: 25 HP (34A)] --> 34A x 1.25 = 42.5A (Largest Motor) |
  • | [Motor 2: 15 HP (21A)] --> 21A x 1.00 = 21.0A |
  • | [Motor 3: 10 HP (14A)] --> 14A x 1.00 = 14.0A |
  • | ------------------------------------------------------------------- |
  • | Total Required Feeder Ampacity = 77.5 Amperes |
  • +-------------------------------------------------------------------------+
  • Identifying the 'Largest Motor'

The 'largest motor' is defined as the motor with the highest full-load current rating in Amperes from the NEC Tables—NOT necessarily the motor with the highest horsepower label.

Note

Multiple Motors of Identical Rating: If two or more motors on the feeder share the exact same highest FLA rating, choose only ONE of those motors to multiply by 125%, and add the remaining motors at 100% of their Table FLA.

Worked Calculation Example 2: Multi-Motor Feeder Sizing

Question: An industrial distribution feeder supplies three 460-Volt, 3-phase motors: Motor A (25 HP), Motor B (15 HP), and Motor C (10 HP). All terminal connections are 75°C. What is the minimum ampacity and size of THWN copper feeder conductors required?

Step 1: Look up NEC Table FLAs (Table 430.250 for 3-Phase AC).

  • Motor A (25 HP @ 460V) = 34 Amperes
  • Motor B (15 HP @ 460V) = 21 Amperes
  • Motor C (10 HP @ 460V) = 14 Amperes

Step 2: Identify the largest motor and calculate feeder ampacity (NEC 430.24).

Largest motor = Motor A (34 A). Feeder Ampacity = ( 34 A × 1.25 ) + 21 A + 14 A \text{Feeder Ampacity} = (34\text{ A} \times 1.25) + 21\text{ A} + 14\text{ A} Feeder Ampacity = ( 34 A × 1.25 ) + 21 A + 14 A Feeder Ampacity = 42.5 A + 21 A + 14 A = 77.5 Amperes \text{Feeder Ampacity} = 42.5\text{ A} + 21\text{ A} + 14\text{ A} = 77.5\text{ Amperes} Feeder Ampacity = 42.5 A + 21 A + 14 A = 77.5 Amperes

Step 3: Select conductor from Table 310.16 (75°C Copper Column).

  • #6 AWG Cu = 65 A (too small)
  • #4 AWG Cu = 85 A (exceeds 77.5 A requirement)

Answer: Feeder Ampacity = 77.5 Amperes ; Conductor Size = #4 AWG THWN Copper .

  • Voltage Ratings & Special Duty Cycle Exceptions
  • Nominal Voltage Differences

If a motor is rated at 208V, use the 208V column in Tables 430.248 or 430.250. If a table only lists 230V ratings and the motor is operated on a 208V supply, NEC Table notes mandate increasing the 230V table FLA value by 10% for 208V calculations.

Non-Continuous Duty Cycle Motors (Table 430.22(E))

Motors used for short-time, intermittent, periodic, or varying duty (such as cranes, hoists, elevator motors, or valve operators) do not use the standard 125% multiplier. Instead, refer to Table 430.22(E) for duty cycle multipliers ranging from 85% to 200% depending on nameplate rating time classification.