Study guide
8.3 Motor Overload Protection & Disconnecting Means
Michigan Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Exam Overview & NEC General Requirements
1.1 Michigan LARA Electrical Licensing & Exam Format 1.2 NEC Article 90 & Code Structure 1.3 NEC Article 100 Essential Definitions 1.4 NEC Article 110 General Installation Requirements
2 Chapter 2: Branch Circuits & Outlets
2.1 Branch Circuit Ratings & Conductor Sizing 2.2 GFCI Protection Requirements (NEC 210.8) 2.3 AFCI & Tamper-Resistant Outlets (NEC 210.12 & 406.12) 2.4 Receptacle Outlets & Dwelling Unit Spacing (NEC 210.52 & 210.11) 2.5 Switches, Receptacles & Wiring Devices (NEC Articles 404 & 406)
3 Chapter 3: Load Calculations for Services & Feeders
3.1 General Lighting & Receptacle Load Calculations 3.2 Fixed Appliance, Dryer, & Cooking Unit Loads 3.3 Dwelling Unit Service & Feeder Calculations 3.4 Commercial & Non-Dwelling Load Calculations
4 Chapter 4: Wiring Methods, Conductors & Insulation
4.1 Conductor Types & Ampacity Sizing 4.2 Ampacity Adjustment & Correction Factors 4.3 Cable Assemblies (NM-B, MC, UF) 4.4 Raceways & Flexible Conduits (EMT, RMC, PVC, FMC)
5 Chapter 5: Conduit Fill, Box Fill & Panelboards
5.1 Raceway Fill Calculations 5.2 Outlet & Junction Box Sizing (NEC 314.16(A)) 5.3 Box Fill Volume Deductions (NEC 314.16(B)) 5.4 Panelboards, Switchboards & Cabinets (NEC Article 408)
6 Chapter 6: Overcurrent Protection Devices & Tap Rules
6.1 Fuses & Circuit Breakers (NEC Article 240) 6.2 Small Conductor Rules & Protection Limits (NEC 240.4(D)) 6.3 Feeder & Transformer Tap Rules (NEC 240.21) 6.4 Location, Enclosures & Overcurrent Protection Accessibility
7 Chapter 7: Grounding & Bonding Systems
7.1 Grounding Electrode Systems & Electrodes (NEC 250.50 & 250.52) 7.2 Grounding Electrode Conductor (GEC) Sizing (NEC Table 250.66) 7.3 Equipment Grounding Conductors (EGC) Sizing (NEC Table 250.122) 7.4 Bonding Requirements & Main Bonding Jumpers
8 Chapter 8: Motors, Generators & Transformers
8.1 Motor Full-Load Current (FLA) & Conductor Sizing (NEC Article 430) 8.2 Motor Short-Circuit & Ground-Fault Protection (Table 430.52) 8.3 Motor Overload Protection & Disconnecting Means 8.4 Transformer Sizing, Protection & Installation (NEC Article 450)
9 Chapter 9: Special Occupancies, Equipment & Conditions
9.1 Hazardous (Classified) Locations (NEC Articles 500-516) 9.2 Commercial Garages, Service Stations & Healthcare Facilities (Articles 511, 514, 517) 9.3 Swimming Pools, Fountains & Equipotential Bonding (NEC Article 680) 9.4 Renewable Energy Systems & Generators (NEC Articles 690, 700, 702)
10 Chapter 10: Michigan Electrical Law, Rules & Code Administration
10.1 Skilled Trades Regulation Act: License Classes, Scope & Supervision 10.2 Licensure, Examination Eligibility, Retakes & Continuing Education 10.3 Michigan Electrical Code Part 8 Rules & the 2023 NEC Adoption 10.4 Michigan Amendments & Key 2023 NEC Changes Enforced in Michigan 10.5 Stille-DeRossett-Hale Act, Permits, Inspections & the AHJ
11 Chapter 11: Electrical Theory & General Trade Knowledge
11.1 Ohm's Law, Power Formulas & Series/Parallel Circuits 11.2 Alternating Current, Single-Phase & Three-Phase Systems 11.3 Power Factor, Efficiency & Transformer Theory 11.4 Voltage Drop, Conductor Resistance & Trade Math
12 Chapter 12: Services & Feeders (Articles 230 & 215)
12.1 Service Conductors, Clearances & Service-Entrance Requirements 12.2 Service Disconnecting Means, Overcurrent Protection & Service Grounding 12.3 Feeders: Sizing, Overcurrent Protection & Article 215 Requirements
13 Chapter 13: Lighting, Appliances & Power-Limited Circuits
13.1 Luminaires & Lighting Installations (NEC Article 410) 13.2 Appliances & Fixed Electric Space Heating (NEC Articles 422 & 424) 13.3 Class 1, Class 2 & Class 3 Power-Limited Circuits (Articles 724 & 725) 13.4 Fire Alarm, Communications & Optical Fiber Systems (Articles 760, 770, 800-820)
8.3 Motor Overload Protection & Disconnecting Means
Key Takeaways Explain This Topic AI
Motor overload protection (NEC Article 430 Part III) protects motor windings, control apparatus, and branch-circuit conductors against excessive heating caused by continuous mechanical overload or low voltage.
Unlike short-circuit protection, overload device sizing is based strictly on the motor NAMEPLATE full-load current rating per NEC 430.6(A)(1) and NEC 430.32.
Standard overload protection sizing under 430.32(A)(1) is 125% of nameplate FLA for motors with a Service Factor >= 1.15 or a marked temperature rise <= 40°C, and 115% of nameplate FLA for all other motors.
NEC 430.109 mandates that motor disconnecting means must be horsepower-rated unless specifically exempted, and NEC 430.110 requires a minimum continuous rating of 115% of the motor Table FLA.
The 'In Sight From' rule (NEC 430.102) requires the disconnecting means to be visible from AND within 50 feet (15 meters) of both the motor controller and the motor location.
Last updated: August 2026
8.3 Motor Overload Protection & Disconnecting Means
Exam Focus: Sizing motor overload relays based on Nameplate FLA (430.32), maximum modified overload limits (430.32(C)), horsepower-rated disconnecting means (430.109), 115% disconnect ampacity (430.110), and the 'In Sight From' location requirement (430.102).
While short-circuit devices protect against high-magnitude faults, motor overload protection guards against thermal breakdown caused by moderate overcurrents persisting over time. In addition, disconnecting means ensure safe isolation for maintenance personnel. Both areas represent core testing domains on Michigan licensing exams.
Motor Overload Protection (NEC Article 430 Part III)
An overload is defined in Article 100 as operation of equipment in excess of normal full-load rating, which, when persisting for sufficient time, causes damage or dangerous overheating. Overload devices (such as thermal heater elements, electronic overload relays, or integral thermal protectors) respond to time-temperature heating curves. +---------------------------------------------------------------------------------+
- | OVERLOAD SIZING BASED ON MOTOR NAMEPLATE FLA |
- +---------------------------------------------------------------------------------+
- | STANDARD MAXIMUM TRIP RATING (NEC 430.32(A)(1)): |
- | • Motors with Service Factor (SF) ≥ 1.15 ---------------> 125% Nameplate |
- | • Motors with Temperature Rise ≤ 40°C ---------------> 125% Nameplate |
- | • All other motors (e.g., SF = 1.0, Temp Rise > 40°C) ---> 115% Nameplate |
- | |
- | MODIFIED MAXIMUM TRIP RATING (NEC 430.32(C) - Motor Starting Trips): |
- | • Motors with Service Factor (SF) ≥ 1.15 ---------------> 140% Nameplate |
- | • Motors with Temperature Rise ≤ 40°C ---------------> 140% Nameplate |
- | • All other motors ---------------> 130% Nameplate |
- +---------------------------------------------------------------------------------+
[!CRITICAL] Nameplate Rule Reminder: Always use the full-load current printed on the physical motor nameplate when calculating overload heater sizes. Using NEC Table FLAs for overload sizing is an automatic failure on exam questions!
Worked Calculation Example 1: Overload Relay Selection
Question: A 15 HP, 230-Volt, 3-phase motor has a physical nameplate rating of 38 Amperes, a Service Factor of 1.15, and a marked temperature rise of 40°C. What is the maximum standard rating for the overload protection devices?
Step 1: Identify Nameplate FLA and Service Factor. Nameplate FLA = 38 Amperes (Ignore Table 430.250 FLA of 42A).
Service Factor = 1.15 → \rightarrow → Qualifies for 125% multiplier.
Step 2: Calculate Overload Rating. Max Overload Rating = 38 A × 1.25 = 47.5 Amperes \text{Max Overload Rating} = 38\text{ A} \times 1.25 = 47.5\text{ Amperes} Max Overload Rating = 38 A × 1.25 = 47.5 Amperes
Step 3: Evaluate Alternative Scenario (SF = 1.00). If the motor nameplate indicated a Service Factor of 1.00 (or Temp Rise of 50°C), the 115% multiplier would apply: Max Overload Rating (SF 1.0) = 38 A × 1.15 = 43.7 Amperes \text{Max Overload Rating (SF 1.0)} = 38\text{ A} \times 1.15 = 43.7\text{ Amperes} Max Overload Rating (SF 1.0) = 38 A × 1.15 = 43.7 Amperes
Answer: Maximum Overload Trip Rating = 47.5 Amperes .
Motor Disconnecting Means (NEC Article 430 Part IX)
NEC Part IX mandates a disconnecting means for each motor controller and motor installation to ensure positive isolation from power sources.
1. Horsepower Rating Requirement (NEC 430.109)
As a general rule, the motor disconnect must be hp-rated (rated in horsepower) matching or exceeding the motor horsepower at operating voltage. Exceptions permit:
Molded-case circuit breakers or non-fused switches listed for motor circuit isolation.
General-use snap switches for small motors (2 HP or less AC).
2. Ampacity Rating Requirement (NEC 430.110(A))
The disconnecting means must have a continuous current rating of not less than 115% of the motor full-load current rating listed in the NEC Tables . Disconnect Ampacity = NEC Table FLA × 1.15 \text{Disconnect Ampacity} = \text{NEC Table FLA} \times 1.15 Disconnect Ampacity = NEC Table FLA × 1.15
The 'In Sight From' Location Requirement (NEC 430.102)
One of the most heavily tested physical installation rules is NEC 430.102 governing disconnect proximity. +---------------------------------------------------------------------------------+
- | NEC ARTICLE 100 / 430.102 DEFINITION |
- | |
- | "IN SIGHT FROM" = VISIBLE AND NOT MORE THAN 15 METERS (50 FEET) APART |
- | |
- | +-------------------+ <--- Max 50 ft & Visible ---> +---------------+ |
- | | Motor Disconnect | ==================================> | Motor & Load | |
- | +-------------------+ +---------------+ |
- +---------------------------------------------------------------------------------+
Dual Proximity Rules:
Controller Disconnect (430.102(A)): A disconnect switch must be located in sight from the motor controller location.
Motor Disconnect (430.102(B)): A disconnect switch must be located in sight from the motor location and driven machinery.
Note
Exception to 430.102(B): A separate disconnect is NOT required in sight from the motor location IF the controller disconnect is individually lockable in the open position in accordance with NEC 110.25 . The provision for locking must remain in place on the switch or circuit breaker whether the lock is present or not.
Summary Comparison: Table FLA vs. Nameplate FLA
To solidify memory for exam day, study this definitive application chart:
- Motor Calculation Parameter Source Current Value Code Section
- Branch Conductor Sizing NEC Tables (430.248 / 430.250) 430.22
- Feeder Conductor Sizing NEC Tables (430.248 / 430.250) 430.24
- Branch Short-Circuit (BCPD) NEC Tables (430.248 / 430.250) 430.52
- Feeder Short-Circuit (OCPD) NEC Tables (430.248 / 430.250) 430.62
- Disconnect Min Ampacity NEC Tables (430.248 / 430.250) 430.110
- Motor Overload Protection Motor Nameplate FLA 430.32