Study guide
6.1 ACCA Manual J Load Calculation & Equipment Selection
Michigan Mechanical Contractor License HVAC
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Michigan Regulatory Framework, Skilled Trades Act & Licensing
1.1 Michigan Skilled Trades Regulation Act (PA 407 of 2016 Article 8) & BCC Organization 1.2 The 14 Work Classification Examinations, Scope of Work & Experience Standards 1.3 Mechanical Permits, Inspection Protocols, Violations & Sanctions 1.4 Construction Lien Act (PA 497 of 1980), Timelines, Notices & Waivers
2 Chapter 2: Heating Equipment & Forced Air Systems
2.1 Warm Air Furnaces: Categories, Configurations & Heat Exchangers 2.2 High-Efficiency Condensing Furnaces & Condensate Management 2.3 Air-Source & Dual-Fuel Heat Pump Systems & Electric Auxiliary Heating 2.4 Ignition Control Systems, Gas Valves, Safety Switches & Sequence of Operation 2.5 Oil-Fired Furnaces, Burners, Fuel-Oil Storage & Piping
3 Chapter 3: Combustion Air, Fuel Gas Venting & Flue Gas Analysis
3.1 Combustion Air Requirements: Standard Method, Known Infiltration & Mechanical Air 3.2 Category I Venting: Type B Vents, Masonry Chimneys & Sizing Rules 3.3 Categories III & IV Venting: Direct-Vent Terminations, Clearances & Polypropylene/PVC 3.4 Combustion Analysis, Flue Gas Spillage & Carbon Monoxide Diagnostics
4 Chapter 4: Fuel Gas Piping Systems & Storage
4.1 Fuel Gas Pipe Sizing: Longest-Length Method & Branch Calculations 4.2 CSST Installation Standards, Mechanical Protection & Electrical Bonding 4.3 Gas Piping Materials, Joining Specifications, Pressure Testing & Purging 4.4 Liquefied Petroleum (LP) Gas: Tank Sizing, Regulators & Vaporization
5 Chapter 5: Refrigeration Cycle, Cooling Systems, Heat Pumps & Packaged Equipment
5.1 Vapor Compression Refrigeration Cycle & Enthalpy Calculations 5.2 Refrigerant Safety Groups, EPA Section 608 & Low-GWP A2L Transition 5.3 System Evacuation, Micron Gauges, Moisture Removal & Leak Detection 5.4 Charging Procedures: Superheat, Subcooling, TXV vs Fixed Orifice Diagnostics 5.5 Water-to-Air & Geothermal Heat Pump Systems 5.6 Ductless Mini-Split & Variable Refrigerant Flow Systems 5.7 Packaged Rooftop Units 2 to 25 Tons: Curbs, Access & Economizers
6 Chapter 6: Load Calculation, Duct Design & Air Distribution
6.1 ACCA Manual J Load Calculation & Equipment Selection 6.2 ACCA Manual D Fundamentals: Friction Rate, Available Static Pressure & Sizing 6.3 Duct Construction Standards (SMACNA), Sheet Metal Gauges & Hangers 6.4 Air Distribution Principles: Throw, Spread, Drop, Face Velocity & System Balancing 6.5 Mechanical Ventilation: ASHRAE 62.2, HRVs, ERVs & Michigan Energy Code Duct Insulation
7 Chapter 7: Commercial Kitchen Hoods & Building Exhaust Systems
7.1 Type I Commercial Kitchen Hoods & Grease Duct Systems 7.2 Type II Hoods, Kitchen Exhaust Fans & Makeup Air 7.3 Clothes Dryer, Bathroom & Hazardous Exhaust Systems
8 Chapter 8: Hydronic Heating, Steam Boilers & Process Piping
8.1 Hydronic Boilers: Low-Pressure Steam, Hot Water, ASME Code Trim & Safety Relief 8.2 Hydronic Loop Configurations: Series Loop, One-Pipe Mono-Flo, Two-Pipe Direct & Reverse Return 8.3 Expansion Tank Sizing, Air Elimination Devices & Circulator Pump Head Calculations 8.4 Steam Heating Specialties: Steam Traps, Hartford Loops, Vacuum Breakers & Water Feeders
9 Chapter 9: Jobsite Safety (MIOSHA), Electrical Controls & Business Management
9.1 MIOSHA Standards: Fall Protection, Confined Spaces, Ladder Safety & PPE 9.2 HVAC Electrical Safety: Lockout/Tagout, Disconnects, Overcurrent Protection & NEC Wire Sizing 9.3 Carbon Monoxide Hazards, HazCom (GHS/SDS) & Refrigerant Safety (ASHRAE 15) 9.4 Contractor Business Practice: Estimating, Contracts, Insurance & Lien Law Compliance
6.1 ACCA Manual J Load Calculation & Equipment Selection
Key Takeaways Explain This Topic AI
LARA's reference list for the HVAC Equipment examination includes ACCA Manual J-2011 and ACCA Manual D-2016, so load calculation is examinable material.
Michigan Residential Code Section M1401.3 requires heating and cooling equipment to be sized in accordance with ACCA Manual S based on loads calculated in accordance with ACCA Manual J.
Manual J uses the 99% winter and 1% summer design conditions from Table 1A for the specific location, not record extremes and not the coldest day the customer remembers.
Every conduction component load follows Q = U x A x Delta-T, where U is the assembly's overall heat transfer coefficient and equals 1 divided by the total R-value.
Heating load is sensible only; cooling load splits into sensible and latent, and the latent share drives the equipment's dehumidification performance, not just its tonnage.
Last updated: September 2026
ACCA Manual J Load Calculation & Equipment Selection
Manual D — duct design, covered in the next section — cannot start until Manual J has finished. Manual J is what tells you how many Btu each room needs and therefore how many cfm each branch must carry. LARA's published reference list for the HVAC Equipment classification names ACCA Manual J-2011 and ACCA Manual D-2016 (Residential Duct Systems) side by side for exactly that reason.
There is a code hook as well. Michigan Residential Code Section M1401.3 states that heating and cooling equipment "shall be sized in accordance with ACCA Manual S ... based on building loads calculated in accordance with ACCA Manual J or other approved heating and cooling calculation methodologies." Load calculation is not a design nicety in Michigan; it is a code requirement for residential work.
Step 1: Design Conditions
Manual J Table 1A publishes outdoor design conditions by location. Two numbers matter:
99% winter design dry bulb — the temperature that outdoor air stays above 99% of the hours in the heating season. Across most of Lower Michigan this lands in the single digits above zero; western Upper Peninsula locations run below zero.
1% summer design dry bulb and mean coincident wet bulb — Michigan summer design dry bulbs generally sit in the mid-to-upper 80s with coincident wet bulbs in the low 70s.
Indoor design is normally 70°F heating and 75°F dry bulb / 50% relative humidity cooling .
Do not design to extremes. A Michigan record low near -20°F is not the design condition. Sizing to a record produces equipment that is grossly oversized for the 3,000 hours a year that actually matter, short cycles, and never dehumidifies. The 99%/1% conditions are deliberate: the design point is exceeded a small number of hours per year, and the building's thermal mass and the occupant's tolerance absorb the difference.
The design temperature difference is simply: Δ T heating = T indoor − T outdoor 99% \Delta T_{\text{heating}} = T_{\text{indoor}} - T_{\text{outdoor 99\%}} Δ T heating = T indoor − T outdoor 99%
For a Detroit-area home at a 6°F design temperature: 70 - 6 = 64°F.
Step 2: The Conduction Loads
Every opaque and glazed assembly obeys one equation: Q = U × A × Δ T Q = U \times A \times \Delta T Q = U × A × Δ T
where U is the overall heat transfer coefficient in Btu/h·ft²·°F, A is the area in square feet, and ΔT is the design temperature difference.
- U and R are reciprocals: U = 1 R total U = \frac{1}{R_{\text{total}}} U = R total 1
- Worked example — one wall
A 2 × 6 wall with R-21 cavity insulation plus sheathing and finishes has a whole-assembly R-value of about R-17 after framing factors. A 40-foot-long, 9-foot-tall wall with 60 ft² of window in it has:
- Gross wall area: 40 ×9 = 360 ft²
- Net opaque wall: 360 - 60 = 300 ft²
- U_wall = 1 / 17 = 0.0588
- Q_wall = 0.0588 ×300 ×64 = 1,129 Btu/h
Now the window. A good double-pane low-E unit has a U-factor of about 0.30 :
Q_window = 0.30 ×60 ×64 = 1,152 Btu/h
Sixty square feet of glass loses slightly more heat than three hundred square feet of wall. That single comparison explains most of what Manual J teaches: glazing area, orientation, and U-factor dominate residential loads.
Repeat for ceiling/roof, floor, foundation walls, slab edge, and doors. Michigan basements matter: below-grade wall and slab losses are calculated against ground temperature, not outdoor air, and Manual J handles them with dedicated factors.
Step 3: Infiltration
Manual J estimates infiltration from construction tightness, the building's exposure, and the presence of a documented blower-door result , then converts air changes to a load: Q sensible = 1.08 × cfm × Δ T Q_{\text{sensible}} = 1.08 \times \text{cfm} \times \Delta T Q sensible = 1.08 × cfm × Δ T
The 1.08 factor is 0.075 lb/ft³ ×0.24 Btu/lb·°F ×60 min/h — standard air density times specific heat times minutes per hour. You use the same constant when you check a furnace's temperature rise or an RTU's delivered capacity.
In cooling, moisture crossing the envelope adds a latent load: Q latent = 0.68 × cfm × Δ W Q_{\text{latent}} = 0.68 \times \text{cfm} \times \Delta W Q latent = 0.68 × cfm × Δ W
where ΔW is the humidity ratio difference in grains per pound.
A tight new Michigan house built to current energy code will have a small infiltration load and a correspondingly larger ventilation obligation — see the mechanical ventilation section later in this guide. An uninsulated 1920s Detroit bungalow will have an infiltration load that dwarfs its conduction load.
Step 4: Cooling-Only Loads
Heating load is sensible only . Cooling adds:
- Load component Sensible Latent
- Conduction through walls, roof, glass ✔
- Solar gain through glazing (orientation, SHGC, shading) ✔
- Infiltration / ventilation air ✔ ✔
- Occupants (roughly 230 Btu/h sensible + 200 Btu/h latent each at residential activity) ✔ ✔
- Appliances, lighting, plug loads ✔ (kitchen/laundry add latent)
- Duct gain/loss in unconditioned space ✔ ✔
Solar gain is orientation-dependent and time-dependent. West glass peaks in late afternoon, exactly when the outdoor dry bulb peaks — which is why a west-facing great room drives the whole-house cooling peak in a Michigan July.
The sensible heat ratio (SHR) is what you carry into equipment selection: SHR = Q sensible Q total \text{SHR} = \frac{Q_{\text{sensible}}}{Q_{\text{total}}} SHR = Q total Q sensible
A Michigan house typically lands around 0.80 to 0.90 SHR — meaning the equipment needs to be selected for good sensible capacity, and a machine chosen only on nominal tonnage may deliver its sensible capacity at the wrong airflow and leave the house cool and damp.
Step 5: Duct Loads
Ducts in an unconditioned attic or a vented crawlspace add load twice: conduction through the duct wall and leakage . Manual J applies duct load factors based on the duct location, insulation R-value, and measured or assumed leakage rate. Moving the ducts inside the conditioned envelope, or sealing and insulating them to the Michigan energy code requirements covered later, is frequently the single largest load reduction available on a retrofit.
Step 6: Equipment Selection (Manual S)
Manual J produces loads. Manual S turns loads into a selected model, comparing the performance-corrected capacity at the actual design conditions — not the nominal rating — against the calculated load:
Equipment Manual S guidance
Cooling (single stage) Total capacity generally 100% to 115% of the total cooling load, with sensible capacity meeting the sensible load at design airflow
Furnace / heating Output capacity generally not more than about 140% of the heating load
Heat pump Selected on the cooling load, then checked for heating capacity at the Michigan design temperature, with balance point and supplemental heat sized accordingly
Michigan Residential Code M1401.3 carries exceptions for multistage and variable refrigerant flow equipment whose loads fall within the manufacturer's published modulating range, and for cases where no published capacity satisfies both total and sensible loads and the next larger standard size is specified.
The oversizing trap. A contractor "adds a half ton for safety." That half ton raises the equipment's cycling rate, shortens run time, cuts the hours available for dehumidification, raises the installed cost, and — on a heat pump — pushes the balance point in the wrong direction. Manual J plus Manual S exists precisely to stop that reflex, and Michigan code requires it.