Study guide

5.6 Ductless Mini-Split & Variable Refrigerant Flow Systems

Michigan Mechanical Contractor License HVAC

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Michigan Regulatory Framework, Skilled Trades Act & Licensing

1.1 Michigan Skilled Trades Regulation Act (PA 407 of 2016 Article 8) & BCC Organization 1.2 The 14 Work Classification Examinations, Scope of Work & Experience Standards 1.3 Mechanical Permits, Inspection Protocols, Violations & Sanctions 1.4 Construction Lien Act (PA 497 of 1980), Timelines, Notices & Waivers

2 Chapter 2: Heating Equipment & Forced Air Systems

2.1 Warm Air Furnaces: Categories, Configurations & Heat Exchangers 2.2 High-Efficiency Condensing Furnaces & Condensate Management 2.3 Air-Source & Dual-Fuel Heat Pump Systems & Electric Auxiliary Heating 2.4 Ignition Control Systems, Gas Valves, Safety Switches & Sequence of Operation 2.5 Oil-Fired Furnaces, Burners, Fuel-Oil Storage & Piping

3 Chapter 3: Combustion Air, Fuel Gas Venting & Flue Gas Analysis

3.1 Combustion Air Requirements: Standard Method, Known Infiltration & Mechanical Air 3.2 Category I Venting: Type B Vents, Masonry Chimneys & Sizing Rules 3.3 Categories III & IV Venting: Direct-Vent Terminations, Clearances & Polypropylene/PVC 3.4 Combustion Analysis, Flue Gas Spillage & Carbon Monoxide Diagnostics

4 Chapter 4: Fuel Gas Piping Systems & Storage

4.1 Fuel Gas Pipe Sizing: Longest-Length Method & Branch Calculations 4.2 CSST Installation Standards, Mechanical Protection & Electrical Bonding 4.3 Gas Piping Materials, Joining Specifications, Pressure Testing & Purging 4.4 Liquefied Petroleum (LP) Gas: Tank Sizing, Regulators & Vaporization

5 Chapter 5: Refrigeration Cycle, Cooling Systems, Heat Pumps & Packaged Equipment

5.1 Vapor Compression Refrigeration Cycle & Enthalpy Calculations 5.2 Refrigerant Safety Groups, EPA Section 608 & Low-GWP A2L Transition 5.3 System Evacuation, Micron Gauges, Moisture Removal & Leak Detection 5.4 Charging Procedures: Superheat, Subcooling, TXV vs Fixed Orifice Diagnostics 5.5 Water-to-Air & Geothermal Heat Pump Systems 5.6 Ductless Mini-Split & Variable Refrigerant Flow Systems 5.7 Packaged Rooftop Units 2 to 25 Tons: Curbs, Access & Economizers

6 Chapter 6: Load Calculation, Duct Design & Air Distribution

6.1 ACCA Manual J Load Calculation & Equipment Selection 6.2 ACCA Manual D Fundamentals: Friction Rate, Available Static Pressure & Sizing 6.3 Duct Construction Standards (SMACNA), Sheet Metal Gauges & Hangers 6.4 Air Distribution Principles: Throw, Spread, Drop, Face Velocity & System Balancing 6.5 Mechanical Ventilation: ASHRAE 62.2, HRVs, ERVs & Michigan Energy Code Duct Insulation

7 Chapter 7: Commercial Kitchen Hoods & Building Exhaust Systems

7.1 Type I Commercial Kitchen Hoods & Grease Duct Systems 7.2 Type II Hoods, Kitchen Exhaust Fans & Makeup Air 7.3 Clothes Dryer, Bathroom & Hazardous Exhaust Systems

8 Chapter 8: Hydronic Heating, Steam Boilers & Process Piping

8.1 Hydronic Boilers: Low-Pressure Steam, Hot Water, ASME Code Trim & Safety Relief 8.2 Hydronic Loop Configurations: Series Loop, One-Pipe Mono-Flo, Two-Pipe Direct & Reverse Return 8.3 Expansion Tank Sizing, Air Elimination Devices & Circulator Pump Head Calculations 8.4 Steam Heating Specialties: Steam Traps, Hartford Loops, Vacuum Breakers & Water Feeders

9 Chapter 9: Jobsite Safety (MIOSHA), Electrical Controls & Business Management

9.1 MIOSHA Standards: Fall Protection, Confined Spaces, Ladder Safety & PPE 9.2 HVAC Electrical Safety: Lockout/Tagout, Disconnects, Overcurrent Protection & NEC Wire Sizing 9.3 Carbon Monoxide Hazards, HazCom (GHS/SDS) & Refrigerant Safety (ASHRAE 15) 9.4 Contractor Business Practice: Estimating, Contracts, Insurance & Lien Law Compliance

5.6 Ductless Mini-Split & Variable Refrigerant Flow Systems

Key Takeaways Explain This Topic AI

PSI lists mini splits in the HVAC Equipment content outline, alongside heat pumps and rooftop units.

Mini-splits and VRF systems use inverter-driven variable-speed compressors and electronic expansion valves, so capacity modulates continuously instead of cycling on and off.

Line sets have a factory precharge length; beyond it the installer adds refrigerant at the manufacturer's rate (commonly about 0.2 ounce per foot on small systems) and there are hard maximum length and elevation limits.

Michigan Mechanical Code Chapter 11 and ASHRAE 15 limit refrigerant quantity by the refrigerant concentration limit for the smallest occupied space a circuit serves, which governs multi-zone and VRF layouts.

Flare joints are the dominant leak point: use a rigid flaring tool, a torque wrench set to the manufacturer's value, and nitrogen purge while brazing any non-flare joint.

Last updated: September 2026

Ductless Mini-Split & Variable Refrigerant Flow Systems

"Mini splits" appear by name in PSI's HVAC Equipment content outline, and they now represent a large share of Michigan retrofit work: additions without duct capacity, converted attics and garages, sunrooms, server closets, and whole-house replacements in homes that never had ducts.

What Makes a Mini-Split Different

A conventional split system is a fixed-capacity machine that satisfies the load by cycling. A mini-split is an inverter-driven, variable-capacity machine that satisfies the load by modulating.

  • Conventional split Inverter mini-split / VRF
  • Compressor Fixed-speed, on/off Inverter-driven variable speed
  • Metering TXV or fixed orifice Electronic expansion valve (EEV) , often one per indoor unit
  • Capacity control Cycling Continuous modulation, commonly 20% to 130% of nominal
  • Indoor air Ducted, one air handler Wall cassette, ceiling cassette, floor console, or short-duct air handler
  • Outdoor coil Single circuit Single or multi-circuit with per-port EEVs

Typical low-ambient heating Loses capacity sharply Cold-climate models hold rated capacity to roughly 5°F and operate well below 0°F

Two practical consequences for Michigan:

Cold-climate (hyper-heat) models change the conversation. A conventional air-source heat pump in Marquette needs a big strip-heat or fuel backup. A cold-climate inverter unit rated to hold capacity near 5°F and to operate to -13°F or lower can carry a much larger fraction of the season. Always select from the manufacturer's extended heating capacity table at the design temperature , not from the nominal tonnage.

Oversizing hurts. An inverter compressor at the bottom of its modulation range is less efficient and dehumidifies poorly. Sizing a 12,000 Btu/h head for a 4,000 Btu/h room produces short cycling and a clammy space.

Line Sets: The Numbers That Fail Inspections

Every manufacturer publishes four limits, and a Michigan mechanical inspector on a rough-in will look for them:

  • Limit Typical single-zone residential range
  • Factory precharge length 15 to 25 feet (charge in the condenser covers this length)
  • Maximum line-set length 50 to 165 feet depending on model
  • Maximum elevation difference 30 to 100 feet between indoor and outdoor units

Additional charge rate Commonly about 0.2 ounce per foot beyond the precharge on small systems; larger multi-zone systems publish their own rate

Worked additional-charge example

A single-zone 18,000 Btu/h heat pump is precharged for 25 feet . The installed line set measures 62 feet . The manufacturer specifies 0.22 oz/ft of additional charge. 62 − 25 = 37 ft beyond precharge 62 - 25 = 37 \text{ ft beyond precharge} 62 − 25 = 37 ft beyond precharge 37 × 0.22 = 8.14 oz added 37 \times 0.22 = 8.14 \text{ oz added} 37 × 0.22 = 8.14 oz added

Weigh it in with a scale accurate to a tenth of an ounce. Charging a mini-split by superheat or subcooling is generally not valid — the EEV is actively controlling superheat, and the correct procedure is weigh-in per the manufacturer's table .

Assembly practice

Flares are the number one leak source. Use a rigid (clutch-type) flaring tool , deburr the tube, use the manufacturer's flare dimension, apply a trace of approved refrigerant oil, and tighten with a torque wrench to the published value — not by feel. Over-torquing a 1/4-inch flare cracks it just as reliably as under-torquing leaks.

Nitrogen purge while brazing any non-flare joint to prevent cupric oxide scale from forming inside the tubing and migrating into the EEV.

Evacuate to 500 microns and hold a decay test with the service valves still closed, then open the valves. Never use the system's refrigerant charge to "purge" the line set.

Insulate both lines separately for their full length, including outdoors, where UV-stable jacketing or wrap is required.

Condensate

Wall and ceiling cassettes rarely have gravity fall to a drain. Most installations use a small condensate lift pump with an integral float switch. Two rules:

The pump's safety switch must be wired to shut the unit down on a high-level condition. An unwired float switch is the most common cause of ceiling damage on cassette installations.

Condensate discharge must terminate at an approved point per the Michigan Mechanical Code condensate provisions — not onto a roof deck, into a wall cavity, or at a doorway where it will glaze in a Michigan January.

Multi-Zone and VRF Architecture

Multi-zone mini-split : one outdoor unit, a branch manifold or multiple ports, two to eight indoor heads. All heads are in the same mode (heating or cooling) at the same time unless the system is heat-recovery capable.

VRF (variable refrigerant flow) : the commercial extension of the same idea.

Heat pump VRF (2-pipe) — all indoor units in the same mode at any moment.

Heat recovery VRF (3-pipe, or 2-pipe with branch selector boxes) — some indoor units cool while others heat, with heat moved from the cooling zones to the heating zones. This is extremely efficient in buildings with simultaneous loads — a Michigan office with a hot server room and a cold north perimeter is the textbook case.

VRF brings a large refrigerant charge and long piping, which raises the code issue below.

Refrigerant Concentration Limit (MMC Chapter 11 / ASHRAE 15)

This is the code item most often missed on mini-split and VRF work, and it is squarely inside the Michigan Mechanical Code's refrigeration chapter.

The rule: for a refrigerating system serving an occupied space, the total refrigerant in the circuit must not exceed the quantity that, if it all leaked into the smallest occupied space served by that circuit, would exceed the refrigerant's Refrigerant Concentration Limit (RCL) . RCL values come from ASHRAE Standard 34 and are expressed in pounds per thousand cubic feet.

Practical application: Allowable charge (lb) = RCL ( lb 1000 ft 3 ) × Volume of smallest occupied space (ft 3 ) 1000 \text{Allowable charge (lb)} = \text{RCL} \left(\frac{\text{lb}}{1000\,\text{ft}^3}\right) \times \frac{\text{Volume of smallest occupied space (ft}^3)}{1000} Allowable charge (lb) = RCL ( 1000 ft 3 lb ​ ) × 1000 Volume of smallest occupied space (ft 3 ) ​

The word smallest is what catches installers. A VRF riser with a 90-pound charge serving twelve offices is evaluated against the smallest of those twelve rooms, not against the building volume. The usual remedies are to split the circuit into smaller charges, to add a listed refrigerant detection and alarm system with mechanical ventilation, or to relocate a head out of the undersized room.

A2L refrigerants raise the stakes

New mini-split and VRF equipment increasingly ships with R-32 or R-454B , which are A2L (lower toxicity, lower flammability) under ASHRAE 34. A2L equipment carries its own charge-limit rules, requires listed leak detection and mitigation on many configurations under UL/CSA 60335-2-40, and demands A2L-rated recovery equipment, vacuum pumps, and leak detectors. Note that UL/CSA 60335-2-40-2022 and UL/CSA 60335-2-89-2021 are both on LARA's published reference list for the refrigeration classification — the state has already put the A2L standards on the table.

Troubleshooting Quick Reference

  • Symptom Likely cause
  • Head short-cycles and space feels clammy Unit oversized for the room; inverter pinned at minimum modulation
  • Low capacity, long line set, no fault code Additional charge never weighed in beyond the precharge length
  • Repeat low-pressure faults after a repair Flare leak; re-flare with a rigid tool and torque wrench
  • EEV noise or hunting Moisture or debris from brazing without nitrogen purge; contaminated EEV
  • Water staining on ceiling below a cassette Condensate lift pump float switch not wired to shut down the unit

Multi-zone unit will not heat one head while cooling another System is a heat-pump (2-pipe) VRF, not a heat-recovery system

Loading diagram... Mini-Split and VRF: Selection, Charge, and Code Checks