Study guide
3.5 Sinks, Lavatories, Drinking Fountains & Emergency Fixtures
Michigan Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Michigan Plumbing Law, Administration & Licensing
1.1 Michigan Skilled Trades Regulation Act (PA 407 Article 11) & Licensing Hierarchy 1.2 Permits, Applications, Inspections & Code Enforcement 1.3 Essential Plumbing Code Definitions & Terminology
2 Chapter 2: General Regulations & Structural Safety
2.1 Piping Protection, Trenching, Bedding & Backfill 2.2 Structural Safety: Boring, Notching & Cutting of Structural Members 2.3 Pipe Hangers, Supports & Spacing Requirements 2.4 Michigan Frost Protection & Underground Piping Depths
3 Chapter 3: Fixtures, Faucets & Fixture Fittings
3.1 Minimum Plumbing Fixtures, Occupancy Calculations & ADA Accessibility 3.2 Installation of Fixtures: Setting, Clearances, Connections & Access 3.3 Water Closets, Urinals & Flushing Devices 3.4 Showers, Bathtubs & Scald Prevention Standards 3.5 Sinks, Lavatories, Drinking Fountains & Emergency Fixtures
4 Chapter 4: Water Heaters & Hot Water Safety
4.1 Water Heater Sizing, Location, Clearances & Combustion Air 4.2 Temperature & Pressure (T&P) Relief Valves & Discharge Piping 4.3 Thermal Expansion Control, Safety Pans & Drain Terminations
5 Chapter 5: Water Supply Sizing & Distribution
5.1 Water Service Sizing & Water Supply Fixture Units (WSFU) 5.2 Water Distribution Pipe Sizing, Velocity & Pressure Drop 5.3 Potable Water Piping Materials, Joining Methods & Valves 5.4 Potable Water System Testing, Disinfection & Commissioning 5.5 Health Care Plumbing: Hospitals, Labs & Medical Offices (MPC 609)
6 Chapter 6: Cross-Connection Control & Backflow Prevention
6.1 Backflow Principles: Backpressure, Backsiphonage & Hazard Levels 6.2 Backflow Prevention Assemblies & Devices 6.3 Installation, Testing & Certification of Backflow Preventers
7 Chapter 7: Sanitary Drainage: Sizing & System Layout
7.1 Drainage Fixture Units (DFU) & Building Drain / Sewer Sizing 7.2 Minimum Slopes, Flow Velocity & Horizontal Drainage Piping 7.3 Soil & Waste Stacks, Stack Offsets & Base Fittings 7.4 Sump Pumps, Sewage Ejectors & Macerating Toilet Systems
8 Chapter 8: Sanitary Drainage: Cleanouts, Materials & Testing
8.1 Cleanout Sizing, Location, Clearances & Direction of Flow 8.2 Drainage Pipe Materials, Drainage Fittings & Prohibited Fittings 8.3 Drainage System Testing: Water, Air & Final Inspection Tests
9 Chapter 9: Indirect & Special Waste Systems
9.1 Air Gaps vs. Air Breaks: Code Definitions, Sizing & Applications 9.2 Food Handling Establishments, Commercial Dishwashers & Beverage Lines 9.3 Chemical, Corrosive & Special Laboratory Waste Systems
10 Chapter 10: Vents & Venting: Principles & Sizing
10.1 Venting Fundamentals: Atmospheric Pressure & Trap Seal Protection 10.2 Vent Stacks, Stack Vents & Individual Vent Sizing Rules 10.3 Vent Terminations, Roof Penetrations & Michigan Frost Closure
11 Chapter 11: Advanced Venting Systems
11.1 Wet Venting: Horizontal & Vertical Rules and Pipe Sizing 11.2 Circuit & Loop Venting: Sizing, Fixture Limits & Relief Vents 11.3 Combination Waste & Vent Systems (CWV) 11.4 Air Admittance Valves (AAVs) & Michigan Part 7 Restrictions
12 Chapter 12: Traps, Interceptors & Separators
12.1 Fixture Trap Design, Trap Seal Depth & Maximum Trap-to-Vent Distance 12.2 Prohibited Traps, Double Trapping & Trap Seal Primer Mechanisms 12.3 Grease Interceptors: Hydromechanical (HGI) vs. Gravity (GGI) 12.4 Oil Separators, Sand Interceptors & Flammable Liquid Separation
13 Chapter 13: Storm Drainage Systems
13.1 Roof Drainage Sizing & Michigan Rainfall Rates 13.2 Primary vs. Secondary (Emergency) Overflow Roof Drainage 13.3 Conductors, Leaders, Building Storm Drains & Sump Systems
14 Chapter 14: Gas Piping Systems: Fuel Gas & Medical Gas
14.1 Fuel Gas Sizing Methods: Longest Length & Branch Sizing 14.2 Fuel Gas Piping Materials, Fittings, Joining & Hangers 14.3 Appliance Shutoffs, Regulators, Sediment Traps & Pressure Testing 14.4 Medical Gas, Vacuum & Nonmedical Oxygen Piping (MPC Chapter 12)
15 Chapter 15: Isometric Drawings & Blueprint Reading
15.1 Isometric Drawing Fundamentals: 30-Degree Axes & Fitting Symbols 15.2 Reading & Interpreting DWV Isometric Riser Diagrams 15.3 Reading & Interpreting Water Supply & Gas Isometric Layouts 15.4 Identifying Code Violations & Layout Errors in Isometric Drawings
16 Chapter 16: Plumbing Math, Calculations & Practical Skills
16.1 45-Degree Offsets, Rolling Offsets & Fitting Allowances 16.2 Grade, Fall, Percentage of Slope & Invert Elevation Calculations 16.3 Volume, Capacity, Head Pressure & Flow Rate Calculations 16.4 Michigan Practical Examination: Soldering, Brazing, Assembly & Safety
3.5 Sinks, Lavatories, Drinking Fountains & Emergency Fixtures
Key Takeaways Explain This Topic AI
Public handwashing lavatories are restricted to a maximum flow rate of 0.5 GPM (or 0.25 gallons per metering cycle) and require open grid strainers to deter vandalism and flooding.
Commercial kitchen sinks and domestic food waste grinders require minimum waste outlets of 1-1/2 inches, with dishwasher drains protected by an air gap or high loop.
Service sinks and mop basins must incorporate backflow protection via an ASSE 1011/1052 vacuum breaker or integral AVB spout with structural bucket support.
Drinking fountains are strictly prohibited in toilet rooms and must feature an angled bubbler orifice with a sanitary guard directing a minimum 4-inch water stream.
ANSI/ISEA Z358.1 mandates emergency eyewashes deliver 0.4 GPM and emergency showers deliver 20 GPM of tepid water (60°F–100°F) for 15 continuous minutes, actuating within 1 second.
Last updated: September 2026
Sinks, Lavatories, Drinking Fountains & Emergency Fixtures
Chapter 4 of the 2021 Michigan Plumbing Code governs a diverse spectrum of specialized plumbing fixtures, from high-efficiency public lavatories and commercial food-service sinks to life-safety emergency eyewash stations. In addition to hydraulic capacity and backflow prevention, licensed journeyman plumbers must comply with water conservation limits, accessibility clearances, and public health mandates that prohibit fixtures from cross-contaminating potable water distribution networks.
1. Lavatories: Flow Rates, Overflows & Grid Strainers
Lavatories (washbasins designed exclusively for handwashing and personal hygiene) are governed by MPC Section 416 :
Waste Outlet Sizing: The minimum diameter of a lavatory waste outlet is 1-1/4 inches (32 mm) .
Overflow Passageways: If a lavatory is manufactured with an integral overflow, the overflow channel must be cast directly into the fixture body, draining waste into the lavatory tailpiece on the inlet side of the P-trap (above the trap weir). Overflow channels must be accessible for sanitary cleaning.
Public Lavatory Strainers (Vandalism Prevention): Under standard commercial practices, lavatories in public multi-user restrooms must be equipped with open grid strainers (perforated metal discs) rather than mechanical pop-up stoppers. Pop-up stoppers in public facilities are frequently vandalized or wedged shut, causing malicious basin overflows that flood commercial tenant spaces.
Maximum Allowable Flow Rates (MPC Table 604.4 & EPAct):
Public Handwashing Lavatories: Maximum flow rate of 0.5 gallons per minute (GPM) (1.9 L/min) at 60 psi.
Metered Faucets: Cycle-activated faucets in public restrooms must deliver not more than 0.25 gallons per metering cycle and remain flowing for at least 10 seconds .
Private / Residential Lavatories: Maximum flow rate of 1.2 to 1.5 GPM at 60 psi (complying with EPA WaterSense standards).
Tempered Water Delivery (Michigan-specific): Michigan adds MPC 416.5 (R 408.30763a): tempered water must be delivered from lavatories and group wash fixtures in public toilet facilities through an approved water-temperature limiting device conforming to ASSE 1070 or CSA B125.3 . Michigan also adds MPC 607.1.2 (R 408.30727c), which caps tempered water at not greater than 110°F (43°C) where controlled by an ASSE 1070/ASME A112.1070/CSA B125.70 limiting device, and Michigan's amended MPC 607.1 (R 408.30735) requires individual temperature-limiting devices at fixtures in elementary schools, child care centers, day care centers, nurseries, adult group homes, adult congregate homes, children's camps, and at accessible plumbing fixtures.
2. Kitchen Sinks, Waste Grinders & Dishwashers
Under MPC Section 413 and 418 , sinks serving culinary and food-handling activities require specialized hydraulic connections to prevent sewer backup into food prep surfaces:
Kitchen Sink Waste Outlet: Minimum diameter of 1-1/2 inches (38 mm) , equipped with an approved basket strainer.
Commercial Food-Service Sinks: Pot-washing, scullery, and three-compartment sanitizing sinks require minimum 2-inch or 3-inch waste connections and must discharge indirectly through an air gap into a floor sink before routing through an approved grease interceptor .
Food Waste Grinders (Commercial & Domestic):
Must connect to a minimum 1-1/2-inch drain trap.
Must be supplied with an independent cold potable water line to solidify animal fats and lubricate cutting impellers during operation.
The disposer outlet must connect either directly to a dedicated P-trap or to a directional baffled wye tailpiece above the sink trap. It must never discharge into an unvented or downstream branch.
Electrical controls must feature a dedicated wall switch or pneumatic countertop button installed within direct line-of-sight of the sink.
Domestic Dishwasher Drainage (MPC Section 409.2): The discharge hose from a residential dishwasher must connect to the sanitary drainage network using one of two approved methods:
Deck-Mounted Air Gap: The drain hose routes upward through an approved physical air gap fitting mounted on the countertop or sink deck (above the flood level rim) before descending to the disposer inlet or branch tailpiece.
High-Loop Method: Where permitted by the local authority, the flexible drain hose must be securely fastened to the underside of the countertop at a minimum elevation of 32 inches AFF (well above the sink flood rim) before connecting to the disposer or sink tailpiece, preventing dirty sink water from siphoning back into the clean dishwasher tub.
3. Service Sinks, Mop Basins & Laundry Trays
Service sinks and mop basins receive heavily contaminated wastewater from floor mopping, chemical sanitizers, and biological soils:
Trap & Waste Sizing: Floor-mounted mop basins and service sinks require a minimum 2-inch or 3-inch trap and drain connection. Laundry trays require a minimum 1-1/2-inch trap and waste.
Floor-Mounted Basins: Mop basins feature a low curb (typically 6 to 10 inches high) to facilitate dumping heavy mop buckets and rolling maintenance carts without manual lifting.
Cross-Connection Prevention on Service Spouts: Faucets on service sinks are routinely equipped with garden hose threads on the spout. Attaching a hose that hangs down into a mop bucket filled with toxic chemical disinfectants and dirty water constitutes a catastrophic cross-connection hazard. Under MPC Section 415.2 and Section 608 , service sink spouts must be protected with an approved backflow preventer : either an integral atmospheric vacuum breaker (AVB / ASSE 1001) or a dedicated hose bibb vacuum breaker (ASSE 1011 / ASSE 1052) . Furthermore, the faucet spout must feature a top wall support brace/strut and an integral bucket hook capable of supporting the full weight of a water-filled mop bucket.
4. Drinking Fountains & Water Coolers
Drinking fountains and electric water coolers (complying with AHRI 1010 and ASME A112.19.3 ) are regulated under MPC Section 410 :
Drain Connection: Drinking fountains must be equipped with a non-removable strainer and connected to an individual P-trap of not less than 1-1/4 inches (32 mm) in diameter.
Strictly Prohibited Locations (MPC Section 410.4): Drinking fountains, water coolers, and bottle filling stations SHALL NOT be installed in public or private toilet rooms or restrooms. Airborne pathogens, fecal aerosols from unlidded flushometer toilets, and chemical cleaning vapors make locating drinking water dispensers inside toilet rooms a grave public health violation.
Bubbler Orifice & Sanitary Guard: Under MPC Section 410.2 , the bubbler orifice must deliver an upward angled water stream to prevent contaminated droplets from falling back onto the orifice. The orifice must be fitted with a non-removable sanitary angled guard that prevents the user's lips, teeth, or hands from touching the water discharge nozzle. The water stream must rise at least 4 inches (102 mm) above the guard to allow sanitary sipping.
Michigan Two-Fountain Mandate (MPC 410.3.1, added by R 408.30758a): Where drinking fountains are required, not fewer than 2 drinking fountains must be provided. A single drinking fountain with two separate spouts that complies with the requirements for both wheelchair users and standing individuals may be substituted for the two separate fountains:
One unit complying with the requirements for people who use a wheelchair: spout maximum 36 inches AFF , with a minimum 27-inch knee clearance.
One high unit: Spout positioned between 38 inches and 43 inches AFF for standing ambulatory individuals who cannot bend comfortably.
Bottle Filling Stations: MPC Section 410.5 permits bottle filling stations to substitute for up to 50% of the required drinking fountains , provided at least one accessible wheelchair-height fountain remains available.
5. Emergency Eyewash & Deluge Showers: ANSI/ISEA Z358.1
Where workers or students handle corrosive chemicals, caustics, or flammable toxins in industrial, educational, or medical environments, emergency eyewash and deluge shower equipment is legally mandated by MPC Section 411 and OSHA / ANSI/ISEA Z358.1 :
Travel Distance & Location Rules
10-Second Travel Rule: Emergency equipment must be accessible within 10 seconds of unimpeded travel (approximately 55 feet normal walking distance) from the chemical hazard.
Same Level: The fixture must be located on the same level as the hazard. Stairs, escalators, or ramps exceeding ADA slope limits are strictly prohibited along the path of travel.
Zero Obstructions: The path must remain completely free of doors, gates, storage pallets, or machinery. If a door separates the hazard from the shower, it must swing in the direction of travel and have no locking hardware.
Hydraulic Flow Rates & Duration
Emergency fixtures must be capable of delivering continuous, uninterrupted water flow for at least 15 minutes :
Emergency Eyewash: Minimum flow of 0.4 GPM (1.5 L/min) at 30 psi for 15 minutes.
Eye/Face Wash: Minimum flow of 3.0 GPM (11.4 L/min) at 30 psi for 15 minutes.
Emergency Deluge Shower: Minimum flow of 20.0 GPM (75.7 L/min) at 30 psi for 15 minutes. The showerhead pattern must disperse a water column at least 20 inches in diameter measured 60 inches above the standing surface.
Tepid Water Delivery (60°F to 100°F)
Under ANSI/ISEA Z358.1 and Michigan's added MPC 607.1.2 item 5 (R 408.30727c), emergency eye wash tepid water limits are not less than 60°F (15.6°C) and not greater than 100°F (37.8°C) , conforming to ASSE 1071 . Michigan's added MPC 411.3 (R 408.30736 / R 408.30758b) further requires that where hot and cold water are supplied to an emergency shower or eyewash station, the temperature be controlled only by a temperature-actuated mixing valve complying with ASSE 1071, and that a water heater supplying such equipment directly comply with ASSE 1085 :
Water colder than 60°F triggers rapid hypothermic shock, causing chemical burn victims to flee the wash station long before the required 15-minute rinse is complete.
Water hotter than 100°F accelerates chemical reactions with skin tissue and causes severe ocular burns.
Tepid water must be controlled by a dedicated ASSE 1071 certified thermostatic emergency mixing valve. ASSE 1071 valves feature an engineered internal cold-water bypass : if the hot water supply fails, the valve automatically delivers full cold water rather than shutting off, ensuring the victim is never deprived of flushing water.
Valve Operation & Stay-Open Actuation
Under ANSI Z358.1, emergency valves must go from full off to full on in 1 second or less using a single, simple manual action (pull rod or large push flag). The valve must be equipped with a stay-open ball valve mechanism that remains fully open hands-free until intentionally pushed closed, freeing both of the victim's hands to physically hold their eyelids open during the 15-minute rinse.
- Specification Emergency Eyewash Emergency Deluge Shower Code / Standard Reference
- Minimum Flow Rate 0.4 GPM 20.0 GPM ANSI/ISEA Z358.1
- Minimum Flow Duration 15 minutes continuous 15 minutes continuous ANSI/ISEA Z358.1
- Dynamic Flow Pressure 30 psi 30 psi ANSI/ISEA Z358.1
- Water Temperature Range 60°F to 100°F (Tepid) 60°F to 100°F (Tepid) ASSE 1071 / ANSI Z358.1
- Valve Actuation Time 1 second or less 1 second or less Stays open without hands
- Maximum Travel Distance 10 seconds (approx 55 ft) 10 seconds (approx 55 ft) Same level; no obstructions