Study guide
14.1 Fuel Gas Sizing Methods: Longest Length & Branch Sizing
Michigan Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Michigan Plumbing Law, Administration & Licensing
1.1 Michigan Skilled Trades Regulation Act (PA 407 Article 11) & Licensing Hierarchy 1.2 Permits, Applications, Inspections & Code Enforcement 1.3 Essential Plumbing Code Definitions & Terminology
2 Chapter 2: General Regulations & Structural Safety
2.1 Piping Protection, Trenching, Bedding & Backfill 2.2 Structural Safety: Boring, Notching & Cutting of Structural Members 2.3 Pipe Hangers, Supports & Spacing Requirements 2.4 Michigan Frost Protection & Underground Piping Depths
3 Chapter 3: Fixtures, Faucets & Fixture Fittings
3.1 Minimum Plumbing Fixtures, Occupancy Calculations & ADA Accessibility 3.2 Installation of Fixtures: Setting, Clearances, Connections & Access 3.3 Water Closets, Urinals & Flushing Devices 3.4 Showers, Bathtubs & Scald Prevention Standards 3.5 Sinks, Lavatories, Drinking Fountains & Emergency Fixtures
4 Chapter 4: Water Heaters & Hot Water Safety
4.1 Water Heater Sizing, Location, Clearances & Combustion Air 4.2 Temperature & Pressure (T&P) Relief Valves & Discharge Piping 4.3 Thermal Expansion Control, Safety Pans & Drain Terminations
5 Chapter 5: Water Supply Sizing & Distribution
5.1 Water Service Sizing & Water Supply Fixture Units (WSFU) 5.2 Water Distribution Pipe Sizing, Velocity & Pressure Drop 5.3 Potable Water Piping Materials, Joining Methods & Valves 5.4 Potable Water System Testing, Disinfection & Commissioning 5.5 Health Care Plumbing: Hospitals, Labs & Medical Offices (MPC 609)
6 Chapter 6: Cross-Connection Control & Backflow Prevention
6.1 Backflow Principles: Backpressure, Backsiphonage & Hazard Levels 6.2 Backflow Prevention Assemblies & Devices 6.3 Installation, Testing & Certification of Backflow Preventers
7 Chapter 7: Sanitary Drainage: Sizing & System Layout
7.1 Drainage Fixture Units (DFU) & Building Drain / Sewer Sizing 7.2 Minimum Slopes, Flow Velocity & Horizontal Drainage Piping 7.3 Soil & Waste Stacks, Stack Offsets & Base Fittings 7.4 Sump Pumps, Sewage Ejectors & Macerating Toilet Systems
8 Chapter 8: Sanitary Drainage: Cleanouts, Materials & Testing
8.1 Cleanout Sizing, Location, Clearances & Direction of Flow 8.2 Drainage Pipe Materials, Drainage Fittings & Prohibited Fittings 8.3 Drainage System Testing: Water, Air & Final Inspection Tests
9 Chapter 9: Indirect & Special Waste Systems
9.1 Air Gaps vs. Air Breaks: Code Definitions, Sizing & Applications 9.2 Food Handling Establishments, Commercial Dishwashers & Beverage Lines 9.3 Chemical, Corrosive & Special Laboratory Waste Systems
10 Chapter 10: Vents & Venting: Principles & Sizing
10.1 Venting Fundamentals: Atmospheric Pressure & Trap Seal Protection 10.2 Vent Stacks, Stack Vents & Individual Vent Sizing Rules 10.3 Vent Terminations, Roof Penetrations & Michigan Frost Closure
11 Chapter 11: Advanced Venting Systems
11.1 Wet Venting: Horizontal & Vertical Rules and Pipe Sizing 11.2 Circuit & Loop Venting: Sizing, Fixture Limits & Relief Vents 11.3 Combination Waste & Vent Systems (CWV) 11.4 Air Admittance Valves (AAVs) & Michigan Part 7 Restrictions
12 Chapter 12: Traps, Interceptors & Separators
12.1 Fixture Trap Design, Trap Seal Depth & Maximum Trap-to-Vent Distance 12.2 Prohibited Traps, Double Trapping & Trap Seal Primer Mechanisms 12.3 Grease Interceptors: Hydromechanical (HGI) vs. Gravity (GGI) 12.4 Oil Separators, Sand Interceptors & Flammable Liquid Separation
13 Chapter 13: Storm Drainage Systems
13.1 Roof Drainage Sizing & Michigan Rainfall Rates 13.2 Primary vs. Secondary (Emergency) Overflow Roof Drainage 13.3 Conductors, Leaders, Building Storm Drains & Sump Systems
14 Chapter 14: Gas Piping Systems: Fuel Gas & Medical Gas
14.1 Fuel Gas Sizing Methods: Longest Length & Branch Sizing 14.2 Fuel Gas Piping Materials, Fittings, Joining & Hangers 14.3 Appliance Shutoffs, Regulators, Sediment Traps & Pressure Testing 14.4 Medical Gas, Vacuum & Nonmedical Oxygen Piping (MPC Chapter 12)
15 Chapter 15: Isometric Drawings & Blueprint Reading
15.1 Isometric Drawing Fundamentals: 30-Degree Axes & Fitting Symbols 15.2 Reading & Interpreting DWV Isometric Riser Diagrams 15.3 Reading & Interpreting Water Supply & Gas Isometric Layouts 15.4 Identifying Code Violations & Layout Errors in Isometric Drawings
16 Chapter 16: Plumbing Math, Calculations & Practical Skills
16.1 45-Degree Offsets, Rolling Offsets & Fitting Allowances 16.2 Grade, Fall, Percentage of Slope & Invert Elevation Calculations 16.3 Volume, Capacity, Head Pressure & Flow Rate Calculations 16.4 Michigan Practical Examination: Soldering, Brazing, Assembly & Safety
14.1 Fuel Gas Sizing Methods: Longest Length & Branch Sizing
Key Takeaways Explain This Topic AI
Natural gas has a specific gravity of approximately 0.60 and a heating value of 1,000 BTU/cu ft (lighter than air, rises and disperses), whereas Liquefied Petroleum (LP / Propane) gas has a specific gravity of 1.50 and a heating value of 2,500 BTU/cu ft (heavier than air, sinks and pools in low spaces).
Volumetric gas flow demand in Cubic Feet per Hour (CFH) is calculated by dividing total appliance input rating in BTU/h by the average heating value of the fuel gas (CFH = BTU/h / Heating Value); under International Fuel Gas Code Section 402, systems must be sized for 100% simultaneous connected load.
Under the Longest Length Sizing Method (IFGC / IFGC Section 402.4.1), the total developed distance from the gas meter or regulator outlet to the most hydraulically remote appliance dictates the single length row used to size every segment across the entire piping network.
Each pipe segment is sized for the cumulative downstream CFH demand it conveys using the fixed longest length row, ensuring total frictional pressure loss does not exceed code allowances (typically 0.5 inch water column for standard low-pressure systems).
Elevated 2-psi hybrid pressure distribution networks utilize line pressure regulators at interior manifolds to drop pressure to appliance operating levels (7 in. w.c. for natural gas, 11 in. w.c. for LP), allowing significantly smaller pipe diameters over long main runs.
Last updated: September 2026
14.1 Fuel Gas Sizing Methods: Longest Length & Branch Sizing
Exam Focus: Fuel gas sizing is core trade knowledge for a working Michigan plumber. Licensing candidates must demonstrate complete fluency in thermodynamic gas properties, converting manufacturer input ratings (BTU/h) into volumetric demand (Cubic Feet per Hour / CFH), understanding the physical hazards of vapor densities, and executing the Longest Length Sizing Method per the International Fuel Gas Code (IFGC) Section 402 . Mastery of low-pressure drops (0.5 in. w.c.) versus elevated pressure systems (2 psi) is essential for code compliance and safety.
Scope note - where fuel gas sits in Michigan. Fuel gas piping is not governed by the Michigan Plumbing Code. Michigan's amended MPC 101.2 (R 408.30711) states that "the design and installation of gas piping ... shall conform to the Michigan mechanical code," and the Michigan Mechanical Code in turn assigns fuel gas distribution piping, fuel gas-fired appliances and their venting systems to the International Fuel Gas Code ; one- and two-family dwellings follow Chapter 24 of the Michigan Residential Code . The three references PSI lists for the Journey Plumber written examination are the 2021 Michigan Plumbing Code, the State Construction Code Act (1972 PA 230), and the Skilled Trades Regulation Act (2016 PA 407) - no fuel gas code. Treat this chapter as supporting trade knowledge that you will need on the job and that may appear in general plumbing-practice questions, not as Michigan Plumbing Code content you can look up during the open-book exam.
1. Thermodynamic Fundamentals: Natural Gas vs. Liquefied Petroleum (LP) Gas
Fuel gas distribution systems handle two primary combustible gases: Natural Gas and Liquefied Petroleum Gas (LP / Propane) . Because these gases exhibit fundamentally different physical, thermodynamic, and combustion characteristics, piping systems engineered for natural gas cannot be supplied with propane without recalculating pipe capacities and converting appliance orifices and regulator spring tensions. +---------------------------------------------------------------------------------------------------+
- | COMPARATIVE PHYSICAL PROPERTIES OF FUEL GASES |
- +-----------------------+-----------------------------------+---------------------------------------+
- | Property | Natural Gas (Methane - CH4) | Propane / LP Gas (C3H8) |
- +-----------------------+-----------------------------------+---------------------------------------+
- | Specific Gravity (SG) | 0.60 (Air = 1.00) | 1.50 to 1.52 (Air = 1.00) |
- | Vapor Density | Lighter than air (rises/disperses)| Heavier than air (sinks/accumulates) |
- | Heating Value (Gross) | ~1,000 BTU/cu ft (standard basis) | ~2,500 BTU/cu ft (gross combustion) |
- | Flammability Range | 5.0% to 15.0% by volume in air | 2.15% to 9.60% by volume in air |
- | Low-Pressure Delivery | 5 to 7 inches water column (w.c.) | 10 to 11 inches water column (w.c.) |
- | Odorant Additive | Mercaptan (t-butyl mercaptan) | Ethyl mercaptan (stenching agent) |
- +-----------------------+-----------------------------------+---------------------------------------+
- The Critical Safety Implication of Specific Gravity
Natural Gas ( S G = 0.60 SG = 0.60 SG = 0.60 ): Because natural gas has a specific gravity substantially lower than air ( 1.00 1.00 1.00 ), any accidental leak or unburned gas discharge rises naturally toward the ceiling and roof framing. In properly ventilated spaces, it vents upward through attic soffits, louvers, or ridge vents, reducing the likelihood of reaching its lower explosive limit ( L E L = 5 % LEL = 5\% L E L = 5% ) at floor level.
Propane ( S G = 1.50 SG = 1.50 SG = 1.50 ): Propane is 50% heavier than ambient air. Leaking propane drops immediately to the floor, behaves like a liquid, and flows into basements, elevator pits, crawlspaces, floor drains, and trenches. It pools in stagnant low-lying areas where it remains undetected until an ignition source (such as a water heater pilot, relay contact, or sump pump switch) triggers a catastrophic deflagration. Consequently, the Michigan Plumbing Code strictly regulates or prohibits the installation of LP-gas appliances and unvented piping in subterranean basements and pits.
2. Converting Heat Demand (BTU/h) to Volumetric Flow (CFH)
Gas piping capacity tables in the International Fuel Gas Code (IFGC) are indexed in Cubic Feet per Hour (CFH) . However, heating equipment manufacturers rate appliances in British Thermal Units per Hour (BTU/h) input capacity. The journeyman plumber must convert input ratings into volumetric gas demand using the gross heating value of the fuel gas: Volumetric Flow (CFH) = Total Appliance Input Rating (BTU/h) Gross Heating Value of Gas (BTU/cu ft) R u l e \mathbf{\text{Volumetric Flow (CFH)} = \frac{\text{Total Appliance Input Rating (BTU/h)}}{\text{Gross Heating Value of Gas (BTU/cu ft)}}Rule} Volumetric Flow (CFH) = Gross Heating Value of Gas (BTU/cu ft) Total Appliance Input Rating (BTU/h) Rule
Standard Heating Values for Code Calculations
Natural Gas Basis: Unless the local serving gas utility (such as DTE Energy or Consumers Energy in Michigan) publishes a specific heating value, the statutory standard default for natural gas sizing under IFGC Section 402.2 is 1,000 BTU per cubic foot ( 1 CFH = 1 , 000 BTU/h 1\text{ CFH} = 1,000\text{ BTU/h} 1 CFH = 1 , 000 BTU/h ): CFH Natural Gas = BTU/h 1 , 000 \text{CFH}_{\text{Natural Gas}} = \frac{\text{BTU/h}}{1,000} CFH Natural Gas = 1 , 000 BTU/h
Example: A high-efficiency condensing furnace rated at 100 , 000 BTU/h 100,000\text{ BTU/h} 100 , 000 BTU/h requires: 100 , 000 BTU/h 1 , 000 BTU/cu ft = 100 CFH \frac{100,000\text{ BTU/h}}{1,000\text{ BTU/cu ft}} = 100\text{ CFH} 1 , 000 BTU/cu ft 100 , 000 BTU/h = 100 CFH
Propane (LP) Basis: Propane delivers roughly 2.5 times the thermal energy of natural gas per unit volume. The code standard heating value for LP-gas is 2,500 BTU per cubic foot ( 1 CFH = 2 , 500 BTU/h 1\text{ CFH} = 2,500\text{ BTU/h} 1 CFH = 2 , 500 BTU/h ): CFH Propane = BTU/h 2 , 500 \text{CFH}_{\text{Propane}} = \frac{\text{BTU/h}}{2,500} CFH Propane = 2 , 500 BTU/h
Example: The same 100 , 000 BTU/h 100,000\text{ BTU/h} 100 , 000 BTU/h furnace operating on propane requires: 100 , 000 BTU/h 2 , 500 BTU/cu ft = 40 CFH \frac{100,000\text{ BTU/h}}{2,500\text{ BTU/cu ft}} = 40\text{ CFH} 2 , 500 BTU/cu ft 100 , 000 BTU/h = 40 CFH
Exam Rule — No Diversity Reduction: In domestic and commercial gas sizing under the International Fuel Gas Code, all connected appliances must be assumed to operate at 100% full firing rate simultaneously . Unlike water supply systems (which apply Hunter's Curve WSFU diversity reductions), fuel gas piping never uses diversity factors. The piping network must satisfy total cumulative load on the coldest design day when furnace, water heater, range, and clothes dryer run concurrently.
3. Pressure Regimes & Allowable Pressure Drops
Gas flows through a pipe only when a pressure differential exists between the point of supply and the appliance burner. As gas moves through the pipe, internal friction against the pipe wall and turbulence through fittings generate a continuous pressure drop. +---------------------------------------------------------------------------------------------------+
- | FUEL GAS PRESSURE CLASSIFICATIONS |
- +------------------------+--------------------------+-----------------------+-----------------------+
- | System Category | Nominal Supply Pressure | Allowable Press. Drop | Typical Piping Use |
- +------------------------+--------------------------+-----------------------+-----------------------+
- | Low-Pressure Natural | 7.0 in. w.c. (~0.25 psi) | 0.5 in. w.c. | Residential/Sm. Comm. |
- | Low-Pressure Propane | 11.0 in. w.c. (~0.40 psi)| 0.5 in. w.c. | LP 2nd-stage to home |
- | Elevated (Medium) Press| 2.0 psi (~55.4 in. w.c.) | 1.0 psi across main | Hybrid / CSST / Manif.|
- | High-Pressure Industrial| Over 2.0 to 5.0+ psi | Engineered / AHJ | Commercial boilers |
- +------------------------+--------------------------+-----------------------+-----------------------+
- The Water Column Metric
Low-pressure fuel gas systems operate at pressures far below 1 pound per square inch (psi). Pressures are measured using a U-tube manometer or Magnehelic gauge calibrated in inches of water column (in. w.c.) : 1 psi = 27.707 inches of water column (in. w.c.) 1\text{ psi} = 27.707\text{ inches of water column (in. w.c.)} 1 psi = 27.707 inches of water column (in. w.c.) 7.0 in. w.c. = 7.0 27.707 ≈ 0.253 psi 7.0\text{ in. w.c.} = \frac{7.0}{27.707} \approx 0.253\text{ psi} 7.0 in. w.c. = 27.707 7.0 ≈ 0.253 psi 0.5 in. w.c. (allowable drop) = 0.5 27.707 ≈ 0.018 psi 0.5\text{ in. w.c. (allowable drop)} = \frac{0.5}{27.707} \approx 0.018\text{ psi} 0.5 in. w.c. (allowable drop) = 27.707 0.5 ≈ 0.018 psi
If pressure drop exceeds 0.5 in. w.c., the burner manifold pressure drops below the appliance rating plate specification, causing delayed ignition, soot production, elevated carbon monoxide ( C O CO CO ), and burner flame rollout.
4. The Longest Length Sizing Method (IFGC Section 402.4.1)
The Longest Length Method is the standard, universal sizing protocol enforced by the International Fuel Gas Code and tested on licensing examinations. It prevents cumulative friction starvation across multi-branch distribution trees. LONGEST LENGTH METHOD DISTRIBUTION SCHEMATIC
- [GAS METER] === Seg A (20') === [Tee 1] === Seg C (20') === [Tee 2] === Seg E (20') === [App 4: Range]
- | | (65 CFH)
- Seg B (10') Seg D (15') (Total: 60')
- | |
- [App 1: Water Heater] [App 2: Furnace]
- (40 CFH) (100 CFH)
- (Total: 30') (Total: 55')
- [Tee 2] === Seg F (25') === [Tee 3] === Seg G (15') === [App 3: Fireplace] (35 CFH)
- (Total Developed Length: 20'+20'+25'+15' = 80')
- Step-by-Step Execution Protocol
Determine the Longest Developed Length ( L max L_{\text{max}} L max ): Measure the actual piping centerline distance from the outlet of the gas utility meter (or second-stage LP regulator) to the most hydraulically remote appliance outlet in the entire building. In the schematic above, the run to the Fireplace is 20 ′ + 20 ′ + 25 ′ + 15 ′ = 80 feet 20' + 20' + 25' + 15' = 80\text{ feet} 2 0 ′ + 2 0 ′ + 2 5 ′ + 1 5 ′ = 80 feet .
Select the Master Sizing Table: Choose the table matching pipe material, gas type, inlet pressure, and allowable drop (e.g., IFGC Table 402.4(1) for Schedule 40 Metallic Pipe, Natural Gas, Inlet < 2 psi < 2\text{ psi} < 2 psi , 0.5 in. w.c. 0.5\text{ in. w.c.} 0.5 in. w.c. drop, S G = 0.60 SG = 0.60 SG = 0.60 ).
Lock the Distance Row: Locate the length row in the table corresponding to L max L_{\text{max}} L max . If the exact length is not listed, round UP to the next higher table row (e.g., if actual length is 72 ft, use the 80 ft row; never round down or interpolate). This single row is now locked and must be used to size EVERY segment in the piping network.
Calculate Segment Load: For each individual pipe segment (trunk or branch), sum the maximum full-load CFH of all appliances served downstream of that segment.
Determine Pipe Size: In the locked distance row, find the smallest pipe diameter whose rated capacity equals or exceeds the cumulative CFH demand of that segment.
Why Do We Use the Longest Length Row for Short Branches? Apprentice plumbers often ask: "Why size Segment B (only 30 ft total from meter) using the 80 ft row?" If Segment B were sized using the 30 ft row, it would allow a higher pressure drop per foot in that branch. When all appliances fire simultaneously, the high friction loss in the main trunk combined with the smaller branch would push total pressure drop at the appliance beyond the 0.5 in. w.c. threshold. Sizing every segment to the system's worst-case hydraulic length guarantees that pressure drop to any appliance will remain safely under 0.5 in. w.c.
5. Master Capacity Table Excerpt (Schedule 40 Metallic Pipe)
The table below is extracted directly from the International Fuel Gas Code / IFGC Table 402.4(1) parameters (Inlet Pressure: Less than 2 psi; Pressure Drop: 0.5 in. w.c.; Specific Gravity: 0.60):
- Nominal Pipe Size (Inches) 10 Ft 20 Ft 30 Ft 40 Ft 50 Ft 60 Ft 70 Ft 80 Ft 90 Ft 100 Ft
- 1/2" 172 118 95 81 72 65 60 56 52 50
- 3/4" 360 247 199 170 151 137 126 117 110 104
- 1" 678 466 374 320 284 257 237 220 207 195
- 1-1/4" 1,390 957 768 657 583 528 486 452 424 400
- 1-1/2" 2,090 1,430 1,150 985 873 791 728 677 635 600
- 2" 4,020 2,760 2,220 1,900 1,680 1,520 1,400 1,300 1,220 1,160
Capacities given in Cubic Feet per Hour (CFH) of Natural Gas (0.60 SG).
6. Comprehensive Worked Sizing Problem
Using the schematic in Section 4 and the 80-foot locked row from the table above, calculate the required pipe sizes for each segment serving a four-appliance residential layout: +---------------------------------------------------------------------------------------------------+
- | STEP-BY-STEP SIZING CALCULATION AUDIT |
- +---------+--------------------+-----------------------+-----------+------------+-------------------+
- | Segment | Downstream Loads | Appliances Served | Total CFH | 80' Cap. | Selected Size |
- +---------+--------------------+-----------------------+-----------+------------+-------------------+
- | Seg A | App 1+2+3+4 | WH + Furn + Rng + FP | 240 CFH | 452 CFH | 1-1/4" Steel Pipe |
- | Seg B | App 1 only | Water Heater | 40 CFH | 56 CFH | 1/2" Steel Pipe |
- | Seg C | App 2+3+4 | Furn + Rng + FP | 200 CFH | 220 CFH | 1" Steel Pipe |
- | Seg D | App 2 only | Furnace | 100 CFH | 117 CFH | 3/4" Steel Pipe |
- | Seg E | App 4 only | Range | 65 CFH | 117 CFH | 3/4" Steel Pipe |
- | Seg F | App 3 only | Fireplace | 35 CFH | 56 CFH | 1/2" Steel Pipe |
- | Seg G | App 3 only | Fireplace | 35 CFH | 56 CFH | 1/2" Steel Pipe |
- +---------+--------------------+-----------------------+-----------+------------+-------------------+
Mathematical Audit Notes:
Segment A: Carries 40 + 100 + 65 + 35 = 240 CFH 40 + 100 + 65 + 35 = 240\text{ CFH} 40 + 100 + 65 + 35 = 240 CFH . In the 80 ft row, 1" pipe handles only 220 CFH 220\text{ CFH} 220 CFH (undersized). Must step up to 1-1/4" pipe ( 452 CFH 452\text{ CFH} 452 CFH capacity).
Segment C: Carries 100 + 65 + 35 = 200 CFH 100 + 65 + 35 = 200\text{ CFH} 100 + 65 + 35 = 200 CFH . In the 80 ft row, 1" pipe handles 220 CFH 220\text{ CFH} 220 CFH , which satisfies the 200 CFH 200\text{ CFH} 200 CFH demand. Therefore, 1" is correct.
Segment D: Carries 100 CFH 100\text{ CFH} 100 CFH . In the 80 ft row, 1/2" pipe handles only 56 CFH 56\text{ CFH} 56 CFH . Must step up to 3/4" ( 117 CFH 117\text{ CFH} 117 CFH capacity).
7. Elevated Pressure Systems (2 PSI Hybrid Distribution)
In larger residential estates and commercial buildings, running large-diameter black steel pipe (1-1/4" to 2") across long distances is labor-intensive and structurally disruptive. The code permits 2-psi hybrid pressure piping : ELEVATED 2-PSI HYBRID SYSTEM ARCHITECTURE
- [GAS METER] ====> [2-PSI MAIN REGULATOR] ================= (2 PSI Main Trunk) ================>
- |
- [INDOOR MANIFOLD]
- |
- [LINE PRESSURE REGULATOR (PRV)]
- (Reduces 2 psi down to 7" w.c.)
- |
- +-----------------------------+-----------------------------+
- | (7" w.c.) | (7" w.c.) | (7" w.c.)
- [Branch 1] [Branch 2] [Branch 3]
- Water Heater Furnace Range
- Advantages and Code Rules for 2-PSI Systems
Higher Allowable Pressure Drop: The 2-psi main permits an allowable pressure drop of 1.0 psi (28 in. w.c.) across the primary distribution line. This dramatic pressure allowance enables small 1/2" or 3/4" CSST or copper tubing to deliver hundreds of thousands of BTU/h over several hundred feet.
Line Pressure Regulators (ANSI Z21.80): At each appliance group or floor, an approved line pressure regulator drops the 2.0 psi gas down to standard appliance operating pressure ( 7.0 in. w.c. 7.0\text{ in. w.c.} 7.0 in. w.c. for natural gas). Each regulator must have an accessible shutoff valve installed upstream.
- 8. Realistic Exam Application Scenarios
- Scenario A: Sizing an Undersized Commercial Kitchen Line
Exam Scenario: A journeyman plumber in Lansing is retrofitting a commercial restaurant kitchen. The gas meter is located outside, 90 feet developed length from a new commercial wok range requiring 180,000 BTU/h. The plumber plans to tap off an existing 3/4-inch black steel header located 30 feet from the meter that already supplies a 200,000 BTU/h boiler. The total developed length from the meter to the wok range is 100 feet. Can the 3/4-inch header support both appliances?
Code Analysis:
Longest Length: The longest developed length from meter to the most remote appliance is 100 feet 100\text{ feet} 100 feet .
Total Combined Demand: 180 , 000 BTU/h + 200 , 000 BTU/h = 380 , 000 BTU/h = 380 CFH 180,000\text{ BTU/h} + 200,000\text{ BTU/h} = 380,000\text{ BTU/h} = 380\text{ CFH} 180 , 000 BTU/h + 200 , 000 BTU/h = 380 , 000 BTU/h = 380 CFH .
Table Check (100-foot row): Looking at IFGC Table 402.4(1) at 100 feet:
- 3/4" steel pipe capacity = 104 CFH 104\text{ CFH} 104 CFH
- 1" steel pipe capacity = 195 CFH 195\text{ CFH} 195 CFH
- 1-1/4" steel pipe capacity = 400 CFH 400\text{ CFH} 400 CFH
Ruling: The 3/4" pipe can only carry 104 CFH 104\text{ CFH} 104 CFH at 100 feet. Demanding 380 CFH 380\text{ CFH} 380 CFH will starve both appliances, causing severe burner sooting and flame outage. The header from the meter through the first 30 feet must be enlarged to 1-1/4 inch black steel pipe.
Scenario B: Residential Natural Gas to LP Conversion Sizing
Exam Scenario: A homeowner in a rural township outside Flint converts a home from natural gas to LP (propane) gas. The longest run from the LP second-stage tank regulator to the furnace is 60 feet. The furnace is rated at 125,000 BTU/h. An apprentice states that the existing 1/2-inch steel branch line (which was undersized for natural gas) can be safely reused for propane. Is the apprentice correct?
Code Analysis:
Propane Volumetric Conversion: 125 , 000 BTU/h / 2 , 500 BTU/cu ft = 50 CFH 125,000\text{ BTU/h} / 2,500\text{ BTU/cu ft} = 50\text{ CFH} 125 , 000 BTU/h /2 , 500 BTU/cu ft = 50 CFH of LP gas.
Table Check (LP Table, 60-foot length, 1/2" pipe): Under LP piping capacity tables (IFGC Table 402.4(28), 11 in. w.c., 0.5 in. w.c. drop), a 1/2" pipe at 60 feet carries approximately 68 CFH 68\text{ CFH} 68 CFH of propane.
Ruling: Yes, the apprentice is correct. Because propane delivers 2,500 BTU/cu ft compared to 1,000 BTU/cu ft for natural gas, volumetric flow is reduced by 60% ( 50 CFH 50\text{ CFH} 50 CFH vs. 125 CFH 125\text{ CFH} 125 CFH ). The 1/2" branch line easily accommodates the 50 CFH 50\text{ CFH} 50 CFH propane requirement.