Study guide
2.3 Pipe Hangers, Supports & Spacing Requirements
Michigan Journeyman Plumber Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Michigan Plumbing Law, Administration & Licensing
1.1 Michigan Skilled Trades Regulation Act (PA 407 Article 11) & Licensing Hierarchy 1.2 Permits, Applications, Inspections & Code Enforcement 1.3 Essential Plumbing Code Definitions & Terminology
2 Chapter 2: General Regulations & Structural Safety
2.1 Piping Protection, Trenching, Bedding & Backfill 2.2 Structural Safety: Boring, Notching & Cutting of Structural Members 2.3 Pipe Hangers, Supports & Spacing Requirements 2.4 Michigan Frost Protection & Underground Piping Depths
3 Chapter 3: Fixtures, Faucets & Fixture Fittings
3.1 Minimum Plumbing Fixtures, Occupancy Calculations & ADA Accessibility 3.2 Installation of Fixtures: Setting, Clearances, Connections & Access 3.3 Water Closets, Urinals & Flushing Devices 3.4 Showers, Bathtubs & Scald Prevention Standards 3.5 Sinks, Lavatories, Drinking Fountains & Emergency Fixtures
4 Chapter 4: Water Heaters & Hot Water Safety
4.1 Water Heater Sizing, Location, Clearances & Combustion Air 4.2 Temperature & Pressure (T&P) Relief Valves & Discharge Piping 4.3 Thermal Expansion Control, Safety Pans & Drain Terminations
5 Chapter 5: Water Supply Sizing & Distribution
5.1 Water Service Sizing & Water Supply Fixture Units (WSFU) 5.2 Water Distribution Pipe Sizing, Velocity & Pressure Drop 5.3 Potable Water Piping Materials, Joining Methods & Valves 5.4 Potable Water System Testing, Disinfection & Commissioning 5.5 Health Care Plumbing: Hospitals, Labs & Medical Offices (MPC 609)
6 Chapter 6: Cross-Connection Control & Backflow Prevention
6.1 Backflow Principles: Backpressure, Backsiphonage & Hazard Levels 6.2 Backflow Prevention Assemblies & Devices 6.3 Installation, Testing & Certification of Backflow Preventers
7 Chapter 7: Sanitary Drainage: Sizing & System Layout
7.1 Drainage Fixture Units (DFU) & Building Drain / Sewer Sizing 7.2 Minimum Slopes, Flow Velocity & Horizontal Drainage Piping 7.3 Soil & Waste Stacks, Stack Offsets & Base Fittings 7.4 Sump Pumps, Sewage Ejectors & Macerating Toilet Systems
8 Chapter 8: Sanitary Drainage: Cleanouts, Materials & Testing
8.1 Cleanout Sizing, Location, Clearances & Direction of Flow 8.2 Drainage Pipe Materials, Drainage Fittings & Prohibited Fittings 8.3 Drainage System Testing: Water, Air & Final Inspection Tests
9 Chapter 9: Indirect & Special Waste Systems
9.1 Air Gaps vs. Air Breaks: Code Definitions, Sizing & Applications 9.2 Food Handling Establishments, Commercial Dishwashers & Beverage Lines 9.3 Chemical, Corrosive & Special Laboratory Waste Systems
10 Chapter 10: Vents & Venting: Principles & Sizing
10.1 Venting Fundamentals: Atmospheric Pressure & Trap Seal Protection 10.2 Vent Stacks, Stack Vents & Individual Vent Sizing Rules 10.3 Vent Terminations, Roof Penetrations & Michigan Frost Closure
11 Chapter 11: Advanced Venting Systems
11.1 Wet Venting: Horizontal & Vertical Rules and Pipe Sizing 11.2 Circuit & Loop Venting: Sizing, Fixture Limits & Relief Vents 11.3 Combination Waste & Vent Systems (CWV) 11.4 Air Admittance Valves (AAVs) & Michigan Part 7 Restrictions
12 Chapter 12: Traps, Interceptors & Separators
12.1 Fixture Trap Design, Trap Seal Depth & Maximum Trap-to-Vent Distance 12.2 Prohibited Traps, Double Trapping & Trap Seal Primer Mechanisms 12.3 Grease Interceptors: Hydromechanical (HGI) vs. Gravity (GGI) 12.4 Oil Separators, Sand Interceptors & Flammable Liquid Separation
13 Chapter 13: Storm Drainage Systems
13.1 Roof Drainage Sizing & Michigan Rainfall Rates 13.2 Primary vs. Secondary (Emergency) Overflow Roof Drainage 13.3 Conductors, Leaders, Building Storm Drains & Sump Systems
14 Chapter 14: Gas Piping Systems: Fuel Gas & Medical Gas
14.1 Fuel Gas Sizing Methods: Longest Length & Branch Sizing 14.2 Fuel Gas Piping Materials, Fittings, Joining & Hangers 14.3 Appliance Shutoffs, Regulators, Sediment Traps & Pressure Testing 14.4 Medical Gas, Vacuum & Nonmedical Oxygen Piping (MPC Chapter 12)
15 Chapter 15: Isometric Drawings & Blueprint Reading
15.1 Isometric Drawing Fundamentals: 30-Degree Axes & Fitting Symbols 15.2 Reading & Interpreting DWV Isometric Riser Diagrams 15.3 Reading & Interpreting Water Supply & Gas Isometric Layouts 15.4 Identifying Code Violations & Layout Errors in Isometric Drawings
16 Chapter 16: Plumbing Math, Calculations & Practical Skills
16.1 45-Degree Offsets, Rolling Offsets & Fitting Allowances 16.2 Grade, Fall, Percentage of Slope & Invert Elevation Calculations 16.3 Volume, Capacity, Head Pressure & Flow Rate Calculations 16.4 Michigan Practical Examination: Soldering, Brazing, Assembly & Safety
2.3 Pipe Hangers, Supports & Spacing Requirements
Key Takeaways Explain This Topic AI
Maximum horizontal hanger spacing in MPC Table 308.5 varies by material: 32 inches for PEX 1 inch and smaller (48 inches for 1-1/4 inch and larger), 4 feet for PVC/ABS DWV, 5 feet for cast iron, 6 feet for copper tubing 1-1/4 inch and smaller, 10 feet for copper tubing 1-1/2 inch and larger, and 12 feet for steel pipe.
Vertical piping must be supported at its base and at each floor level, with maximum intervals of 10 feet for PEX and copper, and 15 feet for cast iron and steel.
Dissimilar metals must be isolated using dielectric fittings, plastic-coated hangers, or copper-clad straps to prevent destructive galvanic corrosion.
Heavy drainage stacks require rigid structural support at the base, utilizing masonry piers or heavy-duty riser clamps resting on structural framing.
Thermal expansion and contraction in rigid plastic and metallic systems must be accommodated using expansion loops, offsets, or mechanical slip joints.
Last updated: September 2026
2.3 Pipe Hangers, Supports & Spacing Requirements
Exam Focus: Mastery of Michigan Plumbing Code (MPC) Table 308.5 is mandatory for the Journeyman Plumber examination. The exam frequently presents scenario questions asking for the maximum allowable horizontal and vertical hanger spacing across five primary materials: copper, cast iron, PVC/ABS, PEX, and steel . Plumbers must also recognize improper hanging practices that induce galvanic corrosion or trap thermal movement.
1. Code Objectives & Structural Support Fundamentals (MPC 308)
Piping systems must be securely supported to maintain true horizontal slope for drainage, eliminate hydraulic sagging, prevent joint strain, suppress fluid water hammer vibration, and withstand the combined deadweight load of pipe, fittings, valves, and water contents.
Key General Support Rules (MPC 308.1 – 308.4)
Weight Capacity: Hangers, anchors, and structural attachments must be rated to support the total static load of the piping filled completely with water, plus an adequate safety factor.
Alignment & Grade: Hangers must maintain uniform slope without low spots. In horizontal drainage lines, excessive spacing permits plastic pipe to deflect between hangers when exposed to warm discharge water, forming "belly traps" that accumulate solids and cause blockages.
Secure Anchorage: Hangers must attach directly to solid framing members, concrete slabs, or structural steel. Fastening hangers to drywall, metal drop ceilings, or other plumbing pipes is strictly prohibited.
2. MPC Table 308.5: Maximum Hanger Spacing Comparison
The following table represents the statutory horizontal and vertical spacing maximums under MPC Table 308.5. Every journeyman candidate must commit these figures to memory.
Piping Material Maximum Horizontal Spacing Maximum Vertical Spacing Key Installation & Code Conditions
Copper or Copper-Alloy Tubing (≤ 1-1/4" dia.) 6 feet (1.8 m) 10 feet (3.0 m) Supported at each story height; copper-clad or isolated hangers.
Copper or Copper-Alloy Tubing (≥ 1-1/2" dia.) 10 feet (3.0 m) 10 feet (3.0 m) Supported at each story height; insulated against galvanic contact.
Cast Iron Soil Pipe (Hub & Spigot / No-Hub) 5 feet (1.5 m) 15 feet (4.6 m) At every joint; max 10 ft spacing permitted for 10-ft pipe lengths. Base of stack support mandatory.
PVC & ABS DWV Plastic Pipe 4 feet (1.2 m) 10 feet (3.0 m) Continuous slope; vertical support at base and each floor; mid-story guides for 1-1/2" and 2".
Cross-Linked Polyethylene (PEX), 1" and smaller 32 inches (0.8 m) 10 feet (3.0 m) 32" rule without a continuous support channel; mid-story guides on vertical drops.
Cross-Linked Polyethylene (PEX), 1-1/4" and larger 48 inches (1.2 m) 10 feet (3.0 m) Larger PEX gains stiffness and is permitted a 4-foot span.
Steel / Galvanized Iron Pipe 12 feet (3.7 m) 15 feet (4.6 m) High structural rigidity allows long 12-ft horizontal spans.
CPVC Plastic Pipe (≤ 1" dia.) 3 feet (0.9 m) 10 feet (3.0 m) For hot/cold water supply distribution; mid-story guide.
CPVC Plastic Pipe (≥ 1-1/4" dia.) 4 feet (1.2 m) 10 feet (3.0 m) Vertical support at each floor level.
Polypropylene (PP), 1" and smaller 32 inches (0.8 m) 10 feet (3.0 m) Table 308.5 treats small PP like small PEX.
Polypropylene (PP), 1-1/4" and larger 4 feet (1.2 m) 10 feet (3.0 m) Spacing also limited by SDR and operating temperature. HORIZONTAL HANGER SPACING COMPARISON AT A GLANCE
PEX Tubing (32"):
[H]---- 32" ----[H]---- 32" ----[H]
PVC / ABS DWV (4 Ft):
[H]-------- 4 Ft --------[H]-------- 4 Ft --------[H]
Cast Iron No-Hub (5 Ft):
[H]---------- 5 Ft ----------[H]---------- 5 Ft ----------[H]
Copper <= 1-1/4" (6 Ft):
[H]------------- 6 Ft -------------[H]------------- 6 Ft -------------[H]
Copper >= 1-1/2" (10 Ft):
[H]---------------------- 10 Ft ----------------------[H]
Steel Pipe (12 Ft):
- [H]-------------------------- 12 Ft --------------------------[H]
- 3. Hanger Hardware, Design & Galvanic Isolation
- Common Hanger Types & Applications
Clevis Hangers: Adjustable teardrop-shaped yoke with a cross-bolt supporting horizontal pipe runs suspended by all-thread rod. Widely used for commercial DWV and water mains.
Band / Teardrop Hangers: Formed sheet-metal loop supporting light-to-medium horizontal lines.
J-Hooks & Talon Clamps: Rigid plastic or plastic-coated steel hooks nailed directly to wood joist faces; standard for horizontal PEX, CPVC, and copper runs in residential basements.
Riser Clamps: Two-piece heavy-duty steel clamps bolted tightly around vertical pipe barrels. The clamp ears rest solidly on the floor deck or structural framing to transfer the vertical deadweight of the riser to the building structure.
Trapeze Hangers: Horizontal steel strut channel (Unistrut) suspended from overhead structure by dual threaded rods, carrying multiple parallel piping runs.
Preventing Galvanic Corrosion (MPC 308.1)
Galvanic corrosion occurs when two electrochemically dissimilar metals are in direct electrical contact in the presence of moisture (an electrolyte). For example, copper has a noble galvanic potential (+0.34 V), whereas plain carbon steel or zinc galvanized steel is more active (-0.44 V to -0.76 V). When a copper pipe rests directly on a raw steel hanger, the steel acts as a sacrificial anode, accelerating localized pitting and structural failure.
Mandatory Isolation: Copper piping must be supported using copper-plated (copper-clad) hangers , plastic-coated clamps , or non-conductive dielectric isolation tape/cushions .
Prohibited Hanging Practices:
Suspending plastic pipe (PVC, PEX) with perforated metal strapping (plumber's tape) having sharp, burred edges that slice into pipe walls during expansion cycles.
Using wire ties, drywall screws, bent finish nails, or electrical zip-ties as permanent plumbing supports.
4. Base of Stack Anchoring & Sway Bracing
Vertical drainage stacks in multi-story buildings experience severe dynamic loads. When a column of waste water descends down a stack at terminal velocity (approx. 10 to 15 feet per second) and impacts the 90-degree transition fitting at the building drain, it creates massive downward hydraulic thrust and lateral kinetic shock.
Base of Stack Anchorage (MPC 308.7 and 308.7.1)
Rigid Foundation: MPC 308.7 requires anchorage to restrain drainage piping from axial movement, and 308.7.1 requires anchors at the base of every stack and at horizontal changes of direction. Accepted means of carrying the dead and impact load at the base of a stack are: a masonry pier , an engineered concrete pedestal , or a heavy-duty structural steel bracket anchored to building concrete.
Sway Bracing: Horizontal branches connected to large vertical stacks must be secured with longitudinal and transverse sway braces to prevent fitting fatigue and joint displacement during hydraulic surges. BASE OF STACK SUPPORT
- +-------------+
- | Soil Stack | <-- Vertical stack (Supported at each floor)
- | |
- | | |
- | v |
- | +---+ |
- | | | |
- +----+ +----+===============> Building Drain
- | Long-Turn Wye/Sweep Fitting
- +-------------+
- | MASONRY PIER| <-- Permanent concrete/masonry footing
- | OR HEAVY | to absorb hydraulic impact
- | STEEL BRKT |
- +=============+ <-- Concrete Slab / Sub-base
- 5. Thermal Expansion & Contraction Engineering (MPC 308.8)
All piping materials expand and contract with temperature fluctuations. If piping is rigidly restrained between structural boundaries without allowance for movement, thermal stress will cause bowed pipes, snapped fittings, or pulled joints.
Thermal Elongation Rates
PVC Plastic: Expands approximately 3.6 inches per 100 feet per 100°F temperature differential .
PEX Tubing: Expands approximately 1.1 inches per 100 feet per 10°F temperature differential (exceptionally high thermal mobility).
Copper Tubing: Expands approximately 1.1 inches per 100 feet per 100°F temperature differential .
Cast Iron: Expands approximately 0.7 inch per 100 feet per 100°F temperature differential .
Accommodation Methods
Expansion Loops (U-Bends): Engineered pipe loops fabricated with four 90-degree elbows that flex to absorb linear elongation on long hot-water mains.
Offsets & Swing Joints: Directing piping around a 90-degree corner before anchoring, allowing the leg to flex naturally.
Slip Expansion Joints: Mechanical telescoping joints with internal elastomeric O-ring seals, utilized in tall vertical PVC/ABS drainage stacks.