Study guide

16.2 Grade, Fall, Percentage of Slope & Invert Elevation Calculations

Michigan Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Michigan Plumbing Law, Administration & Licensing

1.1 Michigan Skilled Trades Regulation Act (PA 407 Article 11) & Licensing Hierarchy 1.2 Permits, Applications, Inspections & Code Enforcement 1.3 Essential Plumbing Code Definitions & Terminology

2 Chapter 2: General Regulations & Structural Safety

2.1 Piping Protection, Trenching, Bedding & Backfill 2.2 Structural Safety: Boring, Notching & Cutting of Structural Members 2.3 Pipe Hangers, Supports & Spacing Requirements 2.4 Michigan Frost Protection & Underground Piping Depths

3 Chapter 3: Fixtures, Faucets & Fixture Fittings

3.1 Minimum Plumbing Fixtures, Occupancy Calculations & ADA Accessibility 3.2 Installation of Fixtures: Setting, Clearances, Connections & Access 3.3 Water Closets, Urinals & Flushing Devices 3.4 Showers, Bathtubs & Scald Prevention Standards 3.5 Sinks, Lavatories, Drinking Fountains & Emergency Fixtures

4 Chapter 4: Water Heaters & Hot Water Safety

4.1 Water Heater Sizing, Location, Clearances & Combustion Air 4.2 Temperature & Pressure (T&P) Relief Valves & Discharge Piping 4.3 Thermal Expansion Control, Safety Pans & Drain Terminations

5 Chapter 5: Water Supply Sizing & Distribution

5.1 Water Service Sizing & Water Supply Fixture Units (WSFU) 5.2 Water Distribution Pipe Sizing, Velocity & Pressure Drop 5.3 Potable Water Piping Materials, Joining Methods & Valves 5.4 Potable Water System Testing, Disinfection & Commissioning 5.5 Health Care Plumbing: Hospitals, Labs & Medical Offices (MPC 609)

6 Chapter 6: Cross-Connection Control & Backflow Prevention

6.1 Backflow Principles: Backpressure, Backsiphonage & Hazard Levels 6.2 Backflow Prevention Assemblies & Devices 6.3 Installation, Testing & Certification of Backflow Preventers

7 Chapter 7: Sanitary Drainage: Sizing & System Layout

7.1 Drainage Fixture Units (DFU) & Building Drain / Sewer Sizing 7.2 Minimum Slopes, Flow Velocity & Horizontal Drainage Piping 7.3 Soil & Waste Stacks, Stack Offsets & Base Fittings 7.4 Sump Pumps, Sewage Ejectors & Macerating Toilet Systems

8 Chapter 8: Sanitary Drainage: Cleanouts, Materials & Testing

8.1 Cleanout Sizing, Location, Clearances & Direction of Flow 8.2 Drainage Pipe Materials, Drainage Fittings & Prohibited Fittings 8.3 Drainage System Testing: Water, Air & Final Inspection Tests

9 Chapter 9: Indirect & Special Waste Systems

9.1 Air Gaps vs. Air Breaks: Code Definitions, Sizing & Applications 9.2 Food Handling Establishments, Commercial Dishwashers & Beverage Lines 9.3 Chemical, Corrosive & Special Laboratory Waste Systems

10 Chapter 10: Vents & Venting: Principles & Sizing

10.1 Venting Fundamentals: Atmospheric Pressure & Trap Seal Protection 10.2 Vent Stacks, Stack Vents & Individual Vent Sizing Rules 10.3 Vent Terminations, Roof Penetrations & Michigan Frost Closure

11 Chapter 11: Advanced Venting Systems

11.1 Wet Venting: Horizontal & Vertical Rules and Pipe Sizing 11.2 Circuit & Loop Venting: Sizing, Fixture Limits & Relief Vents 11.3 Combination Waste & Vent Systems (CWV) 11.4 Air Admittance Valves (AAVs) & Michigan Part 7 Restrictions

12 Chapter 12: Traps, Interceptors & Separators

12.1 Fixture Trap Design, Trap Seal Depth & Maximum Trap-to-Vent Distance 12.2 Prohibited Traps, Double Trapping & Trap Seal Primer Mechanisms 12.3 Grease Interceptors: Hydromechanical (HGI) vs. Gravity (GGI) 12.4 Oil Separators, Sand Interceptors & Flammable Liquid Separation

13 Chapter 13: Storm Drainage Systems

13.1 Roof Drainage Sizing & Michigan Rainfall Rates 13.2 Primary vs. Secondary (Emergency) Overflow Roof Drainage 13.3 Conductors, Leaders, Building Storm Drains & Sump Systems

14 Chapter 14: Gas Piping Systems: Fuel Gas & Medical Gas

14.1 Fuel Gas Sizing Methods: Longest Length & Branch Sizing 14.2 Fuel Gas Piping Materials, Fittings, Joining & Hangers 14.3 Appliance Shutoffs, Regulators, Sediment Traps & Pressure Testing 14.4 Medical Gas, Vacuum & Nonmedical Oxygen Piping (MPC Chapter 12)

15 Chapter 15: Isometric Drawings & Blueprint Reading

15.1 Isometric Drawing Fundamentals: 30-Degree Axes & Fitting Symbols 15.2 Reading & Interpreting DWV Isometric Riser Diagrams 15.3 Reading & Interpreting Water Supply & Gas Isometric Layouts 15.4 Identifying Code Violations & Layout Errors in Isometric Drawings

16 Chapter 16: Plumbing Math, Calculations & Practical Skills

16.1 45-Degree Offsets, Rolling Offsets & Fitting Allowances 16.2 Grade, Fall, Percentage of Slope & Invert Elevation Calculations 16.3 Volume, Capacity, Head Pressure & Flow Rate Calculations 16.4 Michigan Practical Examination: Soldering, Brazing, Assembly & Safety

16.2 Grade, Fall, Percentage of Slope & Invert Elevation Calculations

Key Takeaways Explain This Topic AI

Total fall represents the total vertical drop of a drainage pipe across its developed length, calculated by multiplying the horizontal length in feet by the installed slope in inches per foot (Total Fall = Length of Run × Slope).

Converting fractional slope per foot to percentage of slope requires dividing the fractional fall by 12 inches and multiplying by 100: a 1/4 inch per foot pitch equals a 2.083% grade, while a 1/8 inch per foot pitch equals a 1.042% grade.

The invert elevation is the vertical benchmark elevation of the lowest inside bottom channel (flowline) of a pipe; downstream Invert Out equals upstream Invert In minus the Total Fall converted to decimal feet.

Trench cut depth calculations must account for the full physical cross-section: Trench Depth = Existing Surface Grade - Invert Elevation + Pipe Wall Thickness + Granular Bedding Depth.

Municipal sewer-authority standards, not the Michigan Plumbing Code, govern drop manhole connections: most Michigan utilities require an inside or outside drop structure whenever an incoming sewer lateral enters a manhole more than 24 inches above the manhole outlet invert.

Last updated: September 2026

16.2 Grade, Fall, Percentage of Slope & Invert Elevation Calculations

Exam Focus: Gravity drainage relies entirely on uniform slope to transport wastewater and suspend solid fecal matter without scouring pipe walls or causing solids deposition. On the Michigan Journeyman Plumber examination, candidates are regularly required to calculate total fall across complex building drains, convert civil engineering percentage slopes into fractional plumber's pitch, determine downstream invert elevations from site benchmarks, and size drop manhole structures under the Michigan Plumbing Code (MPC) Chapter 7 .

1. Grade, Fall & Minimum Slopes under the Michigan Plumbing Code

In plumbing terminology:

Slope (Pitch): The vertical fall per unit of horizontal run, typically expressed in fractions of an inch per foot (e.g., 1 / 4 in/ft 1/4\text{ in/ft} 1/4 in/ft or 1 / 8 in/ft 1/8\text{ in/ft} 1/8 in/ft ).

Total Fall: The total cumulative vertical drop from the starting point of the pipe to the end point, expressed in inches or decimal feet.

Developed Length (Run): The linear distance along the centerline of the pipe, expressed in feet. GRAVITY DRAINAGE PITCH & FALL

  • UPSTREAM INVERT (INV IN)
  • o===================================================+
  • | | TOTAL FALL
  • |<---------------- LENGTH OF RUN (Feet) ----------->| (Inches)
  • | v
  • + - - - - - - - - - - - - - - - - - - - - - - - - - o DOWNSTREAM INVERT
  • (INV OUT)
  • Total Fall (inches) = Length of Run (ft) x Slope (in/ft)

Master Formulas for Slope and Fall Total Fall (Inches) = Length of Run (Feet) × Installed Slope (Inches per Foot) \text{Total Fall (Inches)} = \text{Length of Run (Feet)} \times \text{Installed Slope (Inches per Foot)} Total Fall (Inches) = Length of Run (Feet) × Installed Slope (Inches per Foot) Installed Slope (Inches per Foot) = Total Fall (Inches) Length of Run (Feet) \text{Installed Slope (Inches per Foot)} = \frac{\text{Total Fall (Inches)}}{\text{Length of Run (Feet)}} Installed Slope (Inches per Foot) = Length of Run (Feet) Total Fall (Inches) ​ Length of Run (Feet) = Total Fall (Inches) Installed Slope (Inches per Foot) \text{Length of Run (Feet)} = \frac{\text{Total Fall (Inches)}}{\text{Installed Slope (Inches per Foot)}} Length of Run (Feet) = Installed Slope (Inches per Foot) Total Fall (Inches) ​

Code-Mandated Minimum Slopes (MPC Table 704.1)

Under MPC Section 704.1 , horizontal drainage piping must be installed at uniform slopes to maintain a self-cleansing velocity of not less than 2 feet per second 2\text{ feet per second} 2 feet per second (fps) :

Pipe Diameter (Nominal) Minimum Slope Required (MPC Section 704.1) Fall per 10 Feet Fall per 50 Feet Fall per 100 Feet

  • 2-1/2" or smaller 1/4 inch per foot (2.08%) 2-1/2 inches 12-1/2 inches (1.04') 25.0 inches (2.08')
  • 3" to 6" 1/8 inch per foot (1.04%) 1-1/4 inches 6-1/4 inches (0.52') 12-1/2 inches (1.04')
  • 8" or larger 1/16 inch per foot (0.52%) 5/8 inch 3-1/8 inches (0.26') 6-1/4 inches (0.52')

Note on Velocity: While 1/8 inch per foot is permitted for 3-inch pipes under MPC Table 704.1 where space constraints exist, installing 3-inch horizontal branches at 1/4 inch per foot is standard trade practice in Michigan to ensure adequate scouring velocity for solids.

2. Converting Slope to Percentage of Grade

Civil engineering plans, utility site drawings, and road department profiles specify piping grades as a percentage of slope (%) , whereas plumbers use fractions of an inch per foot . A journeyman must be able to convert effortlessly between these systems.

The Mathematical Conversion Logic

Percentage of slope represents the vertical drop per 100 units of horizontal run (e.g., feet of fall per 100 feet of run). Because there are 12 inches 12\text{ inches} 12 inches in a foot: Slope % = ( Slope in Inches per Foot 12 Inches ) × 100 \text{Slope \%} = \left( \frac{\text{Slope in Inches per Foot}}{12\text{ Inches}} \right) \times 100 Slope % = ( 12 Inches Slope in Inches per Foot ​ ) × 100 Slope in Inches per Foot = Slope % × 12 100 = Slope % × 0.12 \text{Slope in Inches per Foot} = \frac{\text{Slope \%} \times 12}{100} = \text{Slope \%} \times 0.12 Slope in Inches per Foot = 100 Slope % × 12 ​ = Slope % × 0.12

Standard Trade Conversion Table

  • Fractional Slope (in/ft) Decimal Slope (in/ft) Mathematical Calculation Percentage of Slope (%)
  • 1/16 in/ft 0.0625 in/ft ( 0.0625 / 12 ) × 100 (0.0625 / 12) \times 100 ( 0.0625/12 ) × 100 0.521%
  • 1/8 in/ft 0.1250 in/ft ( 0.1250 / 12 ) × 100 (0.1250 / 12) \times 100 ( 0.1250/12 ) × 100 1.042%
  • 3/16 in/ft 0.1875 in/ft ( 0.1875 / 12 ) × 100 (0.1875 / 12) \times 100 ( 0.1875/12 ) × 100 1.563%
  • 1/4 in/ft 0.2500 in/ft ( 0.2500 / 12 ) × 100 (0.2500 / 12) \times 100 ( 0.2500/12 ) × 100 2.083%
  • 5/16 in/ft 0.3125 in/ft ( 0.3125 / 12 ) × 100 (0.3125 / 12) \times 100 ( 0.3125/12 ) × 100 2.604%
  • 3/8 in/ft 0.3750 in/ft ( 0.3750 / 12 ) × 100 (0.3750 / 12) \times 100 ( 0.3750/12 ) × 100 3.125%
  • 1/2 in/ft 0.5000 in/ft ( 0.5000 / 12 ) × 100 (0.5000 / 12) \times 100 ( 0.5000/12 ) × 100 4.167%
  • Conversion Example: Civil Grade to Plumber's Pitch

Problem: A civil utility plan shows a 6-inch building sewer lateral installed at a 1.50 % 1.50\% 1.50% grade. What is the equivalent pitch in inches per foot?

Calculation: Slope = 1.50 × 0.12 = 0.180 inches per foot \text{Slope} = 1.50 \times 0.12 = 0.180\text{ inches per foot} Slope = 1.50 × 0.12 = 0.180 inches per foot

Convert to Fraction: 0.180 × 16 = 2.88 ≈ 3 / 16 in/ft 0.180 \times 16 = 2.88 \approx 3/16\text{ in/ft} 0.180 × 16 = 2.88 ≈ 3/16 in/ft .

Result: The pipe must be laid at slightly less than 3 / 16 inch per foot 3/16\text{ inch per foot} 3/16 inch per foot ( 0.18 in/ft 0.18\text{ in/ft} 0.18 in/ft ). Under MPC 704.1, this exceeds the minimum requirement of 1 / 8 in/ft 1/8\text{ in/ft} 1/8 in/ft ( 1.04 % 1.04\% 1.04% ) and is code-compliant.

3. Invert Elevations & Benchmark Calculations

In architectural and plumbing engineering, all vertical elevations are tied to a established project Benchmark (BM) or a designated datum, such as Finished Floor Elevation (FFE = 100.00') or Mean Sea Level (USGS datum). INVERT & TRENCH ELEVATION ANATOMY

  • SURFACE GRADE ELEVATION (102.50')
  • ======================================================== [GROUND SURFACE]
  • | ^
  • | | TRENCH CUT
  • | PIPE CROWN (TOP OF PIPE) | DEPTH
  • | ----+----------------------------------+---- |
  • | | WALL THICKNESS | |
  • | | | |
  • | ----+-- INVERT ELEVATION (FLOWLINE) ---+---- |
  • | | (Lowest inside bottom channel) | |
  • | | | |
  • | ----+----------------------------------+---- |
  • | | BOTTOM OF PIPE (BOP) | |
  • | ====+==================================+==== |
  • | | GRANULAR BEDDING (4" Minimum) | v
  • +-----+----------------------------------+-------------- [TRENCH BOTTOM]
  • Definitions of Elevation Datums

Invert (INV): The elevation of the lowest inside surface of the pipe channel along which liquid flows (the flowline). This is the governing dimension for all gravity drainage hydraulic calculations.

Crown (Top of Pipe - TOP): The highest outside surface of the pipe wall.

Bottom of Pipe (BOP): The lowest outside surface of the pipe wall ( B O P = I N V − Wall Thickness BOP = INV - \text{Wall Thickness} BOP = I N V − Wall Thickness ).

Invert Out (Downstream): Upstream invert minus total fall: Invert Out = Invert In − Total Fall (in decimal feet) \text{Invert Out} = \text{Invert In} - \text{Total Fall (in decimal feet)} Invert Out = Invert In − Total Fall (in decimal feet) Total Fall (Feet) = Total Fall (Inches) 12 \text{Total Fall (Feet)} = \frac{\text{Total Fall (Inches)}}{12} Total Fall (Feet) = 12 Total Fall (Inches) ​

Calculating Trench Excavation Depth

To excavate a trench accurately, the equipment operator must dig below the invert to allow for the pipe wall and mandatory granular bedding (MPC Section 306.2): Trench Cut Depth = Grade Elevation − Invert Elevation + Pipe Wall Thickness + Bedding Thickness \text{Trench Cut Depth} = \text{Grade Elevation} - \text{Invert Elevation} + \text{Pipe Wall Thickness} + \text{Bedding Thickness} Trench Cut Depth = Grade Elevation − Invert Elevation + Pipe Wall Thickness + Bedding Thickness

4. Deep Sewer Connections & Drop Manholes

When a private building sewer or collection branch discharges into a municipal sewer main or collector manhole, elevation differences between the incoming pipe and the existing sewer main require specialized engineering. EXTERIOR DROP MANHOLE ASSEMBLY

  • INCOMING BUILDING SEWER
  • =============================+ [INSPECTION CLEANOUT TEE]
  • (High Elevation Invert) | |
  • | |
  • | | VERTICAL DROP PIPE
  • | | (External to manhole barrel)
  • MANHOLE WALL | |
  • | | |
  • | DROP EXCEEDS | |
  • | 24 INCHES! | |
  • | | |
  • | | |
  • | +--------+ | (45° or 90° Sweep into benching)
  • | | ========+
  • v v /
  • +--- BENCHING CHANNEL -+===================> OUTLET SEWER INVERT
  • The 24-Inch Drop Rule

Under Michigan municipal utility specifications, Ten States Standards for Wastewater Facilities, and standard plumbing engineering practice:

Mandate: Whenever the invert of an incoming sewer lateral is more than 24 inches 24\text{ inches} 24 inches ( 2.0 feet 2.0\text{ feet} 2.0 feet ) above the downstream outlet invert channel of the manhole, a drop manhole connection must be constructed.

Hydraulic & Structural Rationale:

Solids Separation & Splashing: Wastewater free-falling more than 2 feet violently impacts the manhole floor, splattering sewage onto walls, ladders, and benching, causing fecal solids to adhere and decompose.

Hydrogen Sulfide ( H 2 S H_2S H 2 ​ S ) Release: Free-falling wastewater aerates anaerobic sewage, rapidly stripping deadly, corrosive hydrogen sulfide gas out of solution. H 2 S H_2S H 2 ​ S converts into sulfuric acid ( H 2 S O 4 H_2SO_4 H 2 ​ S O 4 ​ ) via bacterial action on concrete manhole walls, dissolving the structure.

Hydraulic Erosion: Continuous falling cascades erode concrete benching and undermine pipe joints.

Construction Features: A drop manhole utilizes an external vertical drop pipe encased in concrete (or an approved stainless steel internal drop pipe with maintenance clearances), a cleanout tee at the top inline with the incoming lateral for cleaning access, and a smooth sweep at the bottom directing flow into the invert trough in the direction of downstream travel.

  • 5. Realistic Exam Application Scenarios
  • Scenario A: Invert Elevations on a Commercial Lateral Run

Exam Scenario: A journeyman plumber in Ann Arbor is laying 96 feet of 4-inch underground building sewer from the foundation cleanout to the municipal sewer lateral connection at the property line. The plans require a slope of 1/4 inch per foot. The invert elevation at the building foundation cleanout is established at 104.50 feet 104.50\text{ feet} 104.50 feet .

Calculate: (1) Total fall in inches, (2) Total fall in decimal feet, and (3) the downstream invert elevation at the property line.

Calculation Steps:

Calculate Total Fall in Inches: Total Fall = 96 ft × 0.25 in/ft = 24.0 inches \text{Total Fall} = 96\text{ ft} \times 0.25\text{ in/ft} = 24.0\text{ inches} Total Fall = 96 ft × 0.25 in/ft = 24.0 inches

Convert Total Fall to Decimal Feet: Total Fall in Feet = 24.0 inches 12 inches/ft = 2.00 feet \text{Total Fall in Feet} = \frac{24.0\text{ inches}}{12\text{ inches/ft}} = 2.00\text{ feet} Total Fall in Feet = 12 inches/ft 24.0 inches ​ = 2.00 feet

Calculate Downstream Invert Elevation: Downstream Invert = Upstream Invert − Fall in Feet = 104.50 ft − 2.00 ft = 102.50 feet \text{Downstream Invert} = \text{Upstream Invert} - \text{Fall in Feet} = 104.50\text{ ft} - 2.00\text{ ft} = 102.50\text{ feet} Downstream Invert = Upstream Invert − Fall in Feet = 104.50 ft − 2.00 ft = 102.50 feet

Scenario B: Trench Excavation Depth Calculation

Exam Scenario: On a jobsite in Lansing, a 6-inch Schedule 40 PVC sewer lateral (Outside Diameter = 6.625 inches 6.625\text{ inches} 6.625 inches , Wall Thickness = 0.280 inches 0.280\text{ inches} 0.280 inches ) is being installed. At Station 1 + 20 1+20 1 + 20 , the existing surface grade elevation is 614.80 feet 614.80\text{ feet} 614.80 feet , and the pipe invert elevation must be 608.20 feet 608.20\text{ feet} 608.20 feet . The specifications require 4 inches 4\text{ inches} 4 inches ( 0.333 ft 0.333\text{ ft} 0.333 ft ) of crushed stone bedding beneath the pipe.

What is the required total trench excavation depth below existing surface grade?

Calculation Steps:

Calculate Depth from Grade to Pipe Invert: Grade to Invert = 614.80 ft − 608.20 ft = 6.60 feet \text{Grade to Invert} = 614.80\text{ ft} - 608.20\text{ ft} = 6.60\text{ feet} Grade to Invert = 614.80 ft − 608.20 ft = 6.60 feet

Add Pipe Wall Thickness and Bedding:

Wall Thickness in feet: 0.280 in 12 = 0.023 feet \frac{0.280\text{ in}}{12} = 0.023\text{ feet} 12 0.280 in ​ = 0.023 feet

Bedding in feet: 4.0 in 12 = 0.333 feet \frac{4.0\text{ in}}{12} = 0.333\text{ feet} 12 4.0 in ​ = 0.333 feet

Calculate Total Trench Cut Depth: Trench Cut Depth = 6.60 ft + 0.023 ft + 0.333 ft = 6.956 feet (or 6 ’ 11 - 1 / 2 " ) \text{Trench Cut Depth} = 6.60\text{ ft} + 0.023\text{ ft} + 0.333\text{ ft} = 6.956\text{ feet (or } 6\text{' } 11\text{-}1/2") Trench Cut Depth = 6.60 ft + 0.023 ft + 0.333 ft = 6.956 feet (or 6 ’ 11 - 1/2" )