Study guide

16.1 45-Degree Offsets, Rolling Offsets & Fitting Allowances

Michigan Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Michigan Plumbing Law, Administration & Licensing

1.1 Michigan Skilled Trades Regulation Act (PA 407 Article 11) & Licensing Hierarchy 1.2 Permits, Applications, Inspections & Code Enforcement 1.3 Essential Plumbing Code Definitions & Terminology

2 Chapter 2: General Regulations & Structural Safety

2.1 Piping Protection, Trenching, Bedding & Backfill 2.2 Structural Safety: Boring, Notching & Cutting of Structural Members 2.3 Pipe Hangers, Supports & Spacing Requirements 2.4 Michigan Frost Protection & Underground Piping Depths

3 Chapter 3: Fixtures, Faucets & Fixture Fittings

3.1 Minimum Plumbing Fixtures, Occupancy Calculations & ADA Accessibility 3.2 Installation of Fixtures: Setting, Clearances, Connections & Access 3.3 Water Closets, Urinals & Flushing Devices 3.4 Showers, Bathtubs & Scald Prevention Standards 3.5 Sinks, Lavatories, Drinking Fountains & Emergency Fixtures

4 Chapter 4: Water Heaters & Hot Water Safety

4.1 Water Heater Sizing, Location, Clearances & Combustion Air 4.2 Temperature & Pressure (T&P) Relief Valves & Discharge Piping 4.3 Thermal Expansion Control, Safety Pans & Drain Terminations

5 Chapter 5: Water Supply Sizing & Distribution

5.1 Water Service Sizing & Water Supply Fixture Units (WSFU) 5.2 Water Distribution Pipe Sizing, Velocity & Pressure Drop 5.3 Potable Water Piping Materials, Joining Methods & Valves 5.4 Potable Water System Testing, Disinfection & Commissioning 5.5 Health Care Plumbing: Hospitals, Labs & Medical Offices (MPC 609)

6 Chapter 6: Cross-Connection Control & Backflow Prevention

6.1 Backflow Principles: Backpressure, Backsiphonage & Hazard Levels 6.2 Backflow Prevention Assemblies & Devices 6.3 Installation, Testing & Certification of Backflow Preventers

7 Chapter 7: Sanitary Drainage: Sizing & System Layout

7.1 Drainage Fixture Units (DFU) & Building Drain / Sewer Sizing 7.2 Minimum Slopes, Flow Velocity & Horizontal Drainage Piping 7.3 Soil & Waste Stacks, Stack Offsets & Base Fittings 7.4 Sump Pumps, Sewage Ejectors & Macerating Toilet Systems

8 Chapter 8: Sanitary Drainage: Cleanouts, Materials & Testing

8.1 Cleanout Sizing, Location, Clearances & Direction of Flow 8.2 Drainage Pipe Materials, Drainage Fittings & Prohibited Fittings 8.3 Drainage System Testing: Water, Air & Final Inspection Tests

9 Chapter 9: Indirect & Special Waste Systems

9.1 Air Gaps vs. Air Breaks: Code Definitions, Sizing & Applications 9.2 Food Handling Establishments, Commercial Dishwashers & Beverage Lines 9.3 Chemical, Corrosive & Special Laboratory Waste Systems

10 Chapter 10: Vents & Venting: Principles & Sizing

10.1 Venting Fundamentals: Atmospheric Pressure & Trap Seal Protection 10.2 Vent Stacks, Stack Vents & Individual Vent Sizing Rules 10.3 Vent Terminations, Roof Penetrations & Michigan Frost Closure

11 Chapter 11: Advanced Venting Systems

11.1 Wet Venting: Horizontal & Vertical Rules and Pipe Sizing 11.2 Circuit & Loop Venting: Sizing, Fixture Limits & Relief Vents 11.3 Combination Waste & Vent Systems (CWV) 11.4 Air Admittance Valves (AAVs) & Michigan Part 7 Restrictions

12 Chapter 12: Traps, Interceptors & Separators

12.1 Fixture Trap Design, Trap Seal Depth & Maximum Trap-to-Vent Distance 12.2 Prohibited Traps, Double Trapping & Trap Seal Primer Mechanisms 12.3 Grease Interceptors: Hydromechanical (HGI) vs. Gravity (GGI) 12.4 Oil Separators, Sand Interceptors & Flammable Liquid Separation

13 Chapter 13: Storm Drainage Systems

13.1 Roof Drainage Sizing & Michigan Rainfall Rates 13.2 Primary vs. Secondary (Emergency) Overflow Roof Drainage 13.3 Conductors, Leaders, Building Storm Drains & Sump Systems

14 Chapter 14: Gas Piping Systems: Fuel Gas & Medical Gas

14.1 Fuel Gas Sizing Methods: Longest Length & Branch Sizing 14.2 Fuel Gas Piping Materials, Fittings, Joining & Hangers 14.3 Appliance Shutoffs, Regulators, Sediment Traps & Pressure Testing 14.4 Medical Gas, Vacuum & Nonmedical Oxygen Piping (MPC Chapter 12)

15 Chapter 15: Isometric Drawings & Blueprint Reading

15.1 Isometric Drawing Fundamentals: 30-Degree Axes & Fitting Symbols 15.2 Reading & Interpreting DWV Isometric Riser Diagrams 15.3 Reading & Interpreting Water Supply & Gas Isometric Layouts 15.4 Identifying Code Violations & Layout Errors in Isometric Drawings

16 Chapter 16: Plumbing Math, Calculations & Practical Skills

16.1 45-Degree Offsets, Rolling Offsets & Fitting Allowances 16.2 Grade, Fall, Percentage of Slope & Invert Elevation Calculations 16.3 Volume, Capacity, Head Pressure & Flow Rate Calculations 16.4 Michigan Practical Examination: Soldering, Brazing, Assembly & Safety

16.1 45-Degree Offsets, Rolling Offsets & Fitting Allowances

Key Takeaways Explain This Topic AI

A simple 45-degree offset forms an isosceles right triangle where the Set equals the Run, and the Travel equals the Set multiplied by the offset constant 1.4142 (or Set divided by 0.7071).

A rolling offset navigates obstacles across both vertical and horizontal planes; its True Offset equals the square root of the sum of the squares of Rise and Roll (√(Rise² + Roll²)), and its Travel equals True Offset multiplied by 1.4142.

Fitting allowance (also called take-off) is the critical distance from the center of a fitting to the internal pipe shoulder or stop; determining the cut pipe length requires subtracting the fitting allowances of both joints from the center-to-center Travel dimension.

Thread engagement represents the distance male pipe threads screw into a female fitting socket under ANSI/ASME B1.20.1 NPT standards, which must be accounted for when computing fitting allowances for threaded steel piping.

Copper solder cups (ASTM B88) and PVC/CPVC solvent weld sockets (ASTM D2466 / D2665) have standardized insertion depths that establish the stop shoulder from which fitting allowances are measured.

Last updated: September 2026

16.1 45-Degree Offsets, Rolling Offsets & Fitting Allowances

Exam Focus: Calculating pipe offsets and determining exact cut lengths from blueprint dimensions are tested extensively on both the written and practical portions of the Michigan Journeyman Plumber licensing examination. Candidates must master simple 45-degree offset trigonometry, three-dimensional rolling offsets using the Pythagorean theorem, fitting allowance (take-off) deductions, and thread engagement adjustments for threaded pipe under the Michigan Plumbing Code (MPC).

1. Trigonometry of Simple 45-Degree Offsets

A pipe offset is required whenever a piping run must circumvent an architectural obstacle (such as a structural column, ductwork, or another piping system) while continuing parallel to its original axis. The most efficient and hydraulically sound offset in plumbing drainage and supply systems utilizes 45-degree fittings (eighth bends). GEOMETRY OF A SIMPLE 45° OFFSET

  • ORIGINAL RUN OF PIPE
  • ====================+ (Fitting Center 1)
  • | \
  • | \ TRAVEL (Hypotenuse)
  • | \ Travel = Set x 1.4142
  • SET | \ (Center-to-Center of Fittings)
  • (Offset Distance) | \
  • | \
  • | 45° \ (Fitting Center 2)
  • +--------+==================== OFFSET RUN OF PIPE
  • RUN
  • (Parallel Distance)
  • Run = Set = Travel x 0.7071
  • Geometric Elements of the Offset Triangle

A simple 45-degree offset forms an isosceles right triangle ( 45 ∘ − 45 ∘ − 90 ∘ 45^\circ - 45^\circ - 90^\circ 4 5 ∘ − 4 5 ∘ − 9 0 ∘ ):

Set: The perpendicular distance between the centerlines of the original piping run and the offset piping run.

Run: The horizontal (or parallel) distance measured along the original piping axis between the center of the first 45-degree fitting and the center of the second 45-degree fitting. In any simple 45-degree offset, Set = Run \text{Set} = \text{Run} Set = Run .

Travel: The diagonal length of pipe connecting the two 45-degree fittings, measured from the centerline of the first fitting to the centerline of the second fitting (the hypotenuse of the right triangle).

Mathematical Derivations and Constants

Under Euclidean geometry and trigonometry:

sin ⁡ ( 45 ∘ ) = Set Travel = 1 2 ≈ 0.70710678 \sin(45^\circ) = \frac{\text{Set}}{\text{Travel}} = \frac{1}{\sqrt{2}} \approx 0.70710678 sin ( 4 5 ∘ ) = Travel Set ​ = 2 ​ 1 ​ ≈ 0.70710678

csc ⁡ ( 45 ∘ ) = Travel Set = 2 ≈ 1.41421356 \csc(45^\circ) = \frac{\text{Travel}}{\text{Set}} = \sqrt{2} \approx 1.41421356 csc ( 4 5 ∘ ) = Set Travel ​ = 2 ​ ≈ 1.41421356

From these trigonometric functions, journeymen derive two universal offset formulas: Travel = Set × 1.4142 ( or Set 0.7071 ) \text{Travel} = \text{Set} \times 1.4142 \quad \left(\text{or } \frac{\text{Set}}{0.7071}\right) Travel = Set × 1.4142 ( or 0.7071 Set ​ ) Set = Run = Travel × 0.7071 ( or Travel 1.4142 ) \text{Set} = \text{Run} = \text{Travel} \times 0.7071 \quad \left(\text{or } \frac{\text{Travel}}{1.4142}\right) Set = Run = Travel × 0.7071 ( or 1.4142 Travel ​ )

Common Fitting Angles and Multipliers

While 45-degree fittings are standard, journeymen must recognize the constants for all approved directional bends:

  • Fitting Angle Fraction of Circle Multiplier (Travel = Set × Multiplier) Constant (Set = Travel × Constant)
  • 60° Bend 1/6 Bend 1.1547 0.8660
  • 45° Bend 1/8 Bend 1.4142 0.7071
  • 30° Bend 1/12 Bend 2.0000 0.5000
  • 22-1/2° Bend 1/16 Bend 2.6131 0.3827
  • 11-1/4° Bend 1/32 Bend 5.1258 0.1951
  • 2. Geometry and Trigonometry of Rolling Offsets (3D)

A rolling offset occurs when a piping run must change direction across two perpendicular planes simultaneously—for example, moving both upward vertically and outward horizontally to navigate around a building footing or structural girder. 3D ROLLING OFFSET PROJECTION BOX

  • +------------------------------+
  • /| /|
  • / | / |
  • / | / |
  • +------------------------------+ |
  • | | (END VIEW) | |
  • | +-------------*------------|---+ <-- ORIGINAL PIPE AXIS
  • | /| | | /
  • RISE | / | | | / ROLL
  • (Vertical) |/ | | |/ (Horizontal)
  • +---|-------------|------------+
  • | | | |
  • | +-------------+------------+ <-- TRUE OFFSET = √(Rise² + Roll²)
  • | / | /
  • | / v / TRAVEL = True Offset x 1.4142
  • |/ *---------------+ <-- OFFSET PIPE AXIS
  • +---------------------------+
  • The Two-Triangle Concept

To solve a rolling offset, the journeyman visualizes a three-dimensional rectangular prism (box) and calculates two separate right triangles:

The End-View Triangle (Finding True Offset): Looking down the barrel of the pipe, the vertical displacement is the Rise , and the horizontal displacement is the Roll . These two legs form a right triangle whose hypotenuse is the True Offset . True Offset = Rise 2 + Roll 2 \text{True Offset} = \sqrt{\text{Rise}^2 + \text{Roll}^2} True Offset = Rise 2 + Roll 2 ​

The Offset Triangle (Finding Travel): Once the True Offset is established, it functions exactly like the Set in a simple 45-degree offset. The True Offset and the Run form the legs of the second right triangle, whose hypotenuse is the Travel . Travel = True Offset × 1.4142 = Rise 2 + Roll 2 × 1.4142 \text{Travel} = \text{True Offset} \times 1.4142 = \sqrt{\text{Rise}^2 + \text{Roll}^2} \times 1.4142 Travel = True Offset × 1.4142 = Rise 2 + Roll 2 ​ × 1.4142

  • Worked Calculation Examples
  • Worked Example 1: Simple 45° Offset

Problem: A 3-inch copper domestic water line running along a basement ceiling must drop vertically 14 inches 14\text{ inches} 14 inches to clear a rectangular sheet metal supply duct and then resume its horizontal path. Determine the center-to-center Travel distance between the two 45-degree fittings.

Step 1: Identify the Set: Set = 14 inches \text{Set} = 14\text{ inches} Set = 14 inches .

Step 2: Apply the 45-degree multiplier: Travel = 14 in × 1.4142 = 19.7988 inches \text{Travel} = 14\text{ in} \times 1.4142 = 19.7988\text{ inches} Travel = 14 in × 1.4142 = 19.7988 inches

Step 3: Convert decimal inches to trade fractions: 0.7988 × 16 = 12.78 ≈ 13 / 16 inch 0.7988 \times 16 = 12.78 \approx 13/16\text{ inch} 0.7988 × 16 = 12.78 ≈ 13/16 inch

Result: The center-to-center Travel is 19 - 13 / 16 inches 19\text{-}13/16\text{ inches} 19 - 13/16 inches ( 19.80 " 19.80" 19.80" ).

Worked Example 2: Three-Dimensional Rolling Offset

Problem: A 4-inch Schedule 40 PVC sanitary building drain encounters a foundation pier. The pipe must roll 9 inches 9\text{ inches} 9 inches horizontally and rise 12 inches 12\text{ inches} 12 inches vertically using two 45-degree fittings. Calculate the True Offset and the center-to-center Travel length.

Step 1: Calculate the True Offset using the Pythagorean theorem: True Offset = Rise 2 + Roll 2 = 12 2 + 9 2 = 144 + 81 = 225 = 15.0 inches \text{True Offset} = \sqrt{\text{Rise}^2 + \text{Roll}^2} = \sqrt{12^2 + 9^2} = \sqrt{144 + 81} = \sqrt{225} = 15.0\text{ inches} True Offset = Rise 2 + Roll 2 ​ = 1 2 2 + 9 2 ​ = 144 + 81 ​ = 225 ​ = 15.0 inches

Step 2: Calculate Travel from the True Offset: Travel = 15.0 in × 1.4142 = 21.213 inches \text{Travel} = 15.0\text{ in} \times 1.4142 = 21.213\text{ inches} Travel = 15.0 in × 1.4142 = 21.213 inches

Step 3: Convert to fractional inches: 0.213 × 16 = 3.41 ≈ 3 / 16 inch ( 0.213 × 32 = 6.82 ≈ 7 / 32 inch ) 0.213 \times 16 = 3.41 \approx 3/16\text{ inch} \quad (0.213 \times 32 = 6.82 \approx 7/32\text{ inch}) 0.213 × 16 = 3.41 ≈ 3/16 inch ( 0.213 × 32 = 6.82 ≈ 7/32 inch )

Result: The True Offset is 15.0 inches 15.0\text{ inches} 15.0 inches , and the center-to-center Travel is 21 - 7 / 32 inches 21\text{-}7/32\text{ inches} 21 - 7/32 inches ( 21.21 " 21.21" 21.21" ).

3. Fitting Allowances (Take-Off) & Thread Engagement

Calculating the center-to-center Travel distance gives the distance between the geometric centerlines of the two fittings. However, pipe cannot be cut to this dimension. If a pipe is cut to the center-to-center measurement, the assembly will be too long by the combined body length of the two fittings. FITTING ALLOWANCE (TAKE-OFF) DIAGRAM

  • CENTERLINE OF FITTING 1 CENTERLINE OF FITTING 2
  • | |
  • |<----------- TRAVEL (Center-to-Center) --->|
  • | |
  • |<- TAKE-OFF ->| |<- TAKE-OFF ->|
  • +-------+======+=============+======+-------+
  • | |#####/ \#####| |
  • | |####/ \####| |
  • | FITTING 1 | CUT PIPE LENGTH | FITTING 2 |
  • | (45° Bend)| (End-to-End) | (45° Bend)|
  • Definitions of Dimensional Terms

Center-to-Center (C-C): The distance from the intersection of the centerlines of one fitting to the intersection of the centerlines of the adjoining fitting.

Center-to-Face (C-F): The distance from the geometric centerline of the fitting to the extreme outer face of the fitting hub or opening.

Fitting Allowance (Take-Off): The distance from the center of the fitting to the internal stop, shoulder, or thread engagement point where the end of the pipe seats.

Cut Pipe Length (End-to-End): The physical length to which the pipe must be cut: Cut Length = Center-to-Center Travel − ( Fitting Allowance 1 + Fitting Allowance 2 ) \text{Cut Length} = \text{Center-to-Center Travel} - (\text{Fitting Allowance}_1 + \text{Fitting Allowance}_2) Cut Length = Center-to-Center Travel − ( Fitting Allowance 1 ​ + Fitting Allowance 2 ​ )

Thread Engagement for Threaded Steel Pipe (ANSI/ASME B1.20.1 NPT)

For threaded pipe (Schedule 40/80 steel, galvanized, or brass), the pipe enters the fitting socket by a standardized distance known as thread engagement (make-up depth). Under ANSI/ASME B1.20.1, the fitting allowance is determined by subtracting the thread engagement from the center-to-face dimension of the fitting: Fitting Allowance = Center-to-Face − Thread Engagement \text{Fitting Allowance} = \text{Center-to-Face} - \text{Thread Engagement} Fitting Allowance = Center-to-Face − Thread Engagement

Nominal Pipe Size Thread Engagement (Make-Up Depth) Typical 150# Malleable Iron 45° Elbow Center-to-Face Resulting Fitting Allowance (Take-Off)

  • 1/2" 1/2" (0.500") 7/8" (0.875") 3/8" (0.375")
  • 3/4" 9/16" (0.563") 1" (1.000") 7/16" (0.438")
  • 1" 11/16" (0.688") 1-1/8" (1.125") 7/16" (0.438")
  • 1-1/4" 11/16" (0.688") 1-5/16" (1.313") 5/8" (0.625")
  • 1-1/2" 11/16" (0.688") 1-7/16" (1.438") 3/4" (0.750")
  • 2" 3/4" (0.750") 1-11/16" (1.688") 15/16" (0.938")
  • 2-1/2" 15/16" (0.938") 1-15/16" (1.938") 1" (1.000")
  • 3" 1" (1.000") 2-3/16" (2.188") 1-3/16" (1.188")
  • 4" 1-1/8" (1.125") 2-3/4" (2.750") 1-5/8" (1.625")
  • Socket Depths for Copper and Plastic Piping

Copper Tubing (ASTM B88 / ASME B16.22): Fittings have an internal cup with a machined shoulder stop. The fitting allowance is measured from the center of the fitting to the cup shoulder. Solder cup insertion depths range from 0.31 " 0.31" 0.31" for 1/2" tube to 1.31 " 1.31" 1.31" for 3" tube.

PVC / CPVC DWV (ASTM D2665 / D3311): Solvent weld DWV fittings feature sweeping radii. The fitting allowance on a 3-inch PVC DWV 45-degree elbow is typically 1 - 1 / 2 inches 1\text{-}1/2\text{ inches} 1 - 1/2 inches , and on a 4-inch PVC DWV 45-degree elbow it is typically 1 - 7 / 8 inches 1\text{-}7/8\text{ inches} 1 - 7/8 inches .

  • 4. Realistic Exam Application Scenarios
  • Scenario A: Gas Pipe Rolling Offset with Fitting Deductions

Exam Scenario: A journeyman plumber in Grand Rapids is running a 2-inch threaded Schedule 40 black iron gas line to a rooftop unit. To clear a structural steel truss, the line must execute a rolling offset with a vertical Rise of 10 inches 10\text{ inches} 10 inches and a horizontal Roll of 24 inches 24\text{ inches} 24 inches using two 150# malleable iron 45-degree elbows. The center-to-face dimension of each elbow is 1 - 11 / 16 inches 1\text{-}11/16\text{ inches} 1 - 11/16 inches ( 1.688 " 1.688" 1.688" ), and the standard thread engagement is 3 / 4 inch 3/4\text{ inch} 3/4 inch ( 0.750 " 0.750" 0.750" ).

Calculate: (1) True Offset, (2) Center-to-Center Travel, (3) Fitting Allowance per elbow, and (4) the exact cut length of the pipe.

Calculation Steps:

True Offset: True Offset = 10 2 + 24 2 = 100 + 576 = 676 = 26.0 inches \text{True Offset} = \sqrt{10^2 + 24^2} = \sqrt{100 + 576} = \sqrt{676} = 26.0\text{ inches} True Offset = 1 0 2 + 2 4 2 ​ = 100 + 576 ​ = 676 ​ = 26.0 inches

Center-to-Center Travel: Travel = 26.0 in × 1.4142 = 36.769 inches (approx. 36 - 3 / 4 " ) \text{Travel} = 26.0\text{ in} \times 1.4142 = 36.769\text{ inches (approx. } 36\text{-}3/4") Travel = 26.0 in × 1.4142 = 36.769 inches (approx. 36 - 3/4" )

Fitting Allowance per Elbow: Allowance = Center-to-Face − Thread Engagement = 1.688 in − 0.750 in = 0.938 in (or 15 / 16 " ) \text{Allowance} = \text{Center-to-Face} - \text{Thread Engagement} = 1.688\text{ in} - 0.750\text{ in} = 0.938\text{ in (or } 15/16") Allowance = Center-to-Face − Thread Engagement = 1.688 in − 0.750 in = 0.938 in (or 15/16" )

Total Fitting Deduction for Both Fittings: Total Deduction = 0.938 in × 2 = 1.876 in (or 1 - 7 / 8 " ) \text{Total Deduction} = 0.938\text{ in} \times 2 = 1.876\text{ in (or } 1\text{-}7/8") Total Deduction = 0.938 in × 2 = 1.876 in (or 1 - 7/8" )

Cut Pipe Length: Cut Length = 36.769 in − 1.876 in = 34.893 inches (approx. 34 - 7 / 8 " ) \text{Cut Length} = 36.769\text{ in} - 1.876\text{ in} = 34.893\text{ inches (approx. } 34\text{-}7/8") Cut Length = 36.769 in − 1.876 in = 34.893 inches (approx. 34 - 7/8" )

Scenario B: Underground PVC Building Sewer 45° Offset

Exam Scenario: An underground 4-inch PVC building drain requires a simple 45-degree horizontal offset to route around an elevator pit. The required perpendicular Set is 28 inches 28\text{ inches} 28 inches . The manufacturer specification sheet for the 4-inch PVC DWV 45-degree elbows lists a fitting allowance (center-to-shoulder) of 1 - 7 / 8 inches 1\text{-}7/8\text{ inches} 1 - 7/8 inches ( 1.875 " 1.875" 1.875" ) for each fitting.

What is the required cut length of the connecting travel pipe?

Calculation Steps:

Calculate Center-to-Center Travel: Travel = 28.0 in × 1.4142 = 39.598 inches \text{Travel} = 28.0\text{ in} \times 1.4142 = 39.598\text{ inches} Travel = 28.0 in × 1.4142 = 39.598 inches

Calculate Total Fitting Allowance: Total Allowance = 1.875 in + 1.875 in = 3.750 inches \text{Total Allowance} = 1.875\text{ in} + 1.875\text{ in} = 3.750\text{ inches} Total Allowance = 1.875 in + 1.875 in = 3.750 inches

Calculate Cut Pipe Length: Cut Length = 39.598 in − 3.750 in = 35.848 inches (approx. 35 - 27 / 32 " ) \text{Cut Length} = 39.598\text{ in} - 3.750\text{ in} = 35.848\text{ inches (approx. } 35\text{-}27/32") Cut Length = 39.598 in − 3.750 in = 35.848 inches (approx. 35 - 27/32" )