Study guide

5.1 Water Service Sizing & Water Supply Fixture Units (WSFU)

Michigan Journeyman Plumber Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Michigan Plumbing Law, Administration & Licensing

1.1 Michigan Skilled Trades Regulation Act (PA 407 Article 11) & Licensing Hierarchy 1.2 Permits, Applications, Inspections & Code Enforcement 1.3 Essential Plumbing Code Definitions & Terminology

2 Chapter 2: General Regulations & Structural Safety

2.1 Piping Protection, Trenching, Bedding & Backfill 2.2 Structural Safety: Boring, Notching & Cutting of Structural Members 2.3 Pipe Hangers, Supports & Spacing Requirements 2.4 Michigan Frost Protection & Underground Piping Depths

3 Chapter 3: Fixtures, Faucets & Fixture Fittings

3.1 Minimum Plumbing Fixtures, Occupancy Calculations & ADA Accessibility 3.2 Installation of Fixtures: Setting, Clearances, Connections & Access 3.3 Water Closets, Urinals & Flushing Devices 3.4 Showers, Bathtubs & Scald Prevention Standards 3.5 Sinks, Lavatories, Drinking Fountains & Emergency Fixtures

4 Chapter 4: Water Heaters & Hot Water Safety

4.1 Water Heater Sizing, Location, Clearances & Combustion Air 4.2 Temperature & Pressure (T&P) Relief Valves & Discharge Piping 4.3 Thermal Expansion Control, Safety Pans & Drain Terminations

5 Chapter 5: Water Supply Sizing & Distribution

5.1 Water Service Sizing & Water Supply Fixture Units (WSFU) 5.2 Water Distribution Pipe Sizing, Velocity & Pressure Drop 5.3 Potable Water Piping Materials, Joining Methods & Valves 5.4 Potable Water System Testing, Disinfection & Commissioning 5.5 Health Care Plumbing: Hospitals, Labs & Medical Offices (MPC 609)

6 Chapter 6: Cross-Connection Control & Backflow Prevention

6.1 Backflow Principles: Backpressure, Backsiphonage & Hazard Levels 6.2 Backflow Prevention Assemblies & Devices 6.3 Installation, Testing & Certification of Backflow Preventers

7 Chapter 7: Sanitary Drainage: Sizing & System Layout

7.1 Drainage Fixture Units (DFU) & Building Drain / Sewer Sizing 7.2 Minimum Slopes, Flow Velocity & Horizontal Drainage Piping 7.3 Soil & Waste Stacks, Stack Offsets & Base Fittings 7.4 Sump Pumps, Sewage Ejectors & Macerating Toilet Systems

8 Chapter 8: Sanitary Drainage: Cleanouts, Materials & Testing

8.1 Cleanout Sizing, Location, Clearances & Direction of Flow 8.2 Drainage Pipe Materials, Drainage Fittings & Prohibited Fittings 8.3 Drainage System Testing: Water, Air & Final Inspection Tests

9 Chapter 9: Indirect & Special Waste Systems

9.1 Air Gaps vs. Air Breaks: Code Definitions, Sizing & Applications 9.2 Food Handling Establishments, Commercial Dishwashers & Beverage Lines 9.3 Chemical, Corrosive & Special Laboratory Waste Systems

10 Chapter 10: Vents & Venting: Principles & Sizing

10.1 Venting Fundamentals: Atmospheric Pressure & Trap Seal Protection 10.2 Vent Stacks, Stack Vents & Individual Vent Sizing Rules 10.3 Vent Terminations, Roof Penetrations & Michigan Frost Closure

11 Chapter 11: Advanced Venting Systems

11.1 Wet Venting: Horizontal & Vertical Rules and Pipe Sizing 11.2 Circuit & Loop Venting: Sizing, Fixture Limits & Relief Vents 11.3 Combination Waste & Vent Systems (CWV) 11.4 Air Admittance Valves (AAVs) & Michigan Part 7 Restrictions

12 Chapter 12: Traps, Interceptors & Separators

12.1 Fixture Trap Design, Trap Seal Depth & Maximum Trap-to-Vent Distance 12.2 Prohibited Traps, Double Trapping & Trap Seal Primer Mechanisms 12.3 Grease Interceptors: Hydromechanical (HGI) vs. Gravity (GGI) 12.4 Oil Separators, Sand Interceptors & Flammable Liquid Separation

13 Chapter 13: Storm Drainage Systems

13.1 Roof Drainage Sizing & Michigan Rainfall Rates 13.2 Primary vs. Secondary (Emergency) Overflow Roof Drainage 13.3 Conductors, Leaders, Building Storm Drains & Sump Systems

14 Chapter 14: Gas Piping Systems: Fuel Gas & Medical Gas

14.1 Fuel Gas Sizing Methods: Longest Length & Branch Sizing 14.2 Fuel Gas Piping Materials, Fittings, Joining & Hangers 14.3 Appliance Shutoffs, Regulators, Sediment Traps & Pressure Testing 14.4 Medical Gas, Vacuum & Nonmedical Oxygen Piping (MPC Chapter 12)

15 Chapter 15: Isometric Drawings & Blueprint Reading

15.1 Isometric Drawing Fundamentals: 30-Degree Axes & Fitting Symbols 15.2 Reading & Interpreting DWV Isometric Riser Diagrams 15.3 Reading & Interpreting Water Supply & Gas Isometric Layouts 15.4 Identifying Code Violations & Layout Errors in Isometric Drawings

16 Chapter 16: Plumbing Math, Calculations & Practical Skills

16.1 45-Degree Offsets, Rolling Offsets & Fitting Allowances 16.2 Grade, Fall, Percentage of Slope & Invert Elevation Calculations 16.3 Volume, Capacity, Head Pressure & Flow Rate Calculations 16.4 Michigan Practical Examination: Soldering, Brazing, Assembly & Safety

5.1 Water Service Sizing & Water Supply Fixture Units (WSFU)

Key Takeaways Explain This Topic AI

Dr. Roy B. Hunter developed Hunter's Curve to quantify simultaneous fixture demand probability using Water Supply Fixture Units (WSFU).

Under MPC Chapter 6 and Appendix E, fixtures are assigned WSFU ratings that differ significantly between private installations (residential) and public installations (commercial/institutional).

Under MPC Table E103.3(2) a public flushometer-valve water closet is rated at 10.0 WSFU and a public flush-tank water closet at 5.0 WSFU, while the private equivalents are 6.0 and 2.2 WSFU.

Converting WSFU to design flow rate (GPM) requires selecting either the flush tank curve or the flushometer valve curve; flushometer systems require significantly higher GPM at lower unit counts.

MPC Section 603.1 requires that the water service pipe be not less than 3/4 inch in diameter, and MPC 603.2 requires 5 feet of horizontal separation (or approved materials) between a water service and a building sewer sharing a trench.

Last updated: September 2026

5.1 Water Service Sizing & Water Supply Fixture Units (WSFU)

Exam Focus: Journeyman Plumber licensing exam questions regularly test the mathematical and hydraulic principles underlying water supply sizing under Michigan Plumbing Code (MPC) Chapter 6 and Appendix E . Candidates must master the concept of Water Supply Fixture Units (WSFU) , the application of Hunter's Curve for simultaneous demand probability, the distinction between private and public fixture ratings, the conversion of WSFU to Gallons Per Minute (GPM) for flush tank versus flushometer systems, and the statutory 3/4-inch minimum water service size in MPC 603.1 .

1. Hydraulic Foundations: Hunter's Curve & Simultaneous Demand Probability

In early plumbing history, water supply lines were frequently sized by simply adding together the maximum open-valve flow rates of all connected fixtures. This direct summation approach led to grossly oversized piping networks, excessive installation costs, stagnant water volumes, and degraded water quality.

In the 1920s and 1930s, Dr. Roy B. Hunter of the National Bureau of Standards (NBS, now NIST) revolutionized plumbing engineering through landmark research published in BMS65 and BMS79 . Hunter recognized that plumbing fixtures operate intermittently rather than continuously. In any building, the operation of a faucet, shower, or water closet is a probabilistic event governed by three distinct variables:

Discharge Flow Rate (q): The volumetric rate of water flow delivered by the fixture fitting while open (measured in Gallons Per Minute, GPM).

Duration of Operation (t): The average time interval (in seconds) that the fixture valve remains open during a single cycle of use.

Frequency of Use (T): The average time interval (in seconds) between successive operations of the fixture during peak demand hours.

The ratio of operating duration to cycle frequency (p = t / T) defines the probability (p) that a given fixture is operating at any random second during peak usage. Applying the binomial probability distribution theorem, Hunter calculated the probability that m or more fixtures out of a total population of n fixtures would be active at the exact same instant: P(m <= n) = Sum [n! / (x!(n - x)!)] * p^x * (1 - p)^(n - x)

Hunter established a standard design threshold where a piping system must satisfy simultaneous demand with a failure probability of not more than 1% (99% design reliability) . The resulting relationship between connected fixture load and estimated peak volumetric demand is known worldwide as Hunter's Curve . DESIGN FLOW (GPM)

  • ^
  • 100 | . - - - FLUSHOMETER CURVE
  • | . - '
  • 80 | . - - '
  • | . - - ' . - - - - - FLUSH TANK CURVE
  • 60 | . - '
  • | . ' . - - '
  • 40 | / . - - '
  • | / . - - '
  • 20 | / . - - '
  • |'__________________________________________>
  • 0 25 50 75 100 150 200 WSFU LOAD
  • 2. Concept and Definition of Water Supply Fixture Units (WSFU)

To allow plumbers and engineers to calculate complex piping networks without calculating binomial equations for every branch, Hunter devised the Water Supply Fixture Unit (WSFU) .

A Water Supply Fixture Unit is a dimensionless numerical rating assigned to a specific plumbing fixture that reflects its relative demand-producing effect on the water supply distribution network. One WSFU does not represent a fixed number of gallons per minute; rather, it is an arbitrary index factor that factors in flow rate, duration, and frequency of operation relative to other fixtures.

Private vs. Public Fixture Classification (MPC Section 202)

The Michigan Plumbing Code draws a fundamental distinction between fixtures installed in private environments and those installed in public occupancies:

Private Use: Fixtures installed in private residences, single-family dwellings, individual residential apartments, private guest rooms of hotels and motels, and private executive office suites intended for the exclusive use of an individual or family. Peak frequency of use is low, resulting in lower WSFU ratings.

Public Use: Fixtures installed in schools, gymnasiums, office buildings, restaurants, healthcare facilities, assembly halls, commercial establishments, and public restrooms where fixtures are subject to rapid, repeated, sequential operation by transient occupants. The elevated frequency of use mandates substantially higher WSFU ratings.

3. Fixture Unit Ratings: MPC Table E103.3(2)

Water supply fixture unit load values live in Table E103.3(2) of Appendix E , which R 408.30701 adopts along with appendices B, C and D. There is no WSFU table in Chapter 6 - if you are flipping through Chapter 6 looking for one during the open-book exam you are in the wrong part of the book. The table is reproduced in full below:

  • Fixture Occupancy Type of Supply Control Cold WSFU Hot WSFU Total WSFU
  • Bathroom group Private Flush tank water closet 2.7 1.5 3.6
  • Bathroom group Private Flushometer valve water closet 6.0 3.0 8.0
  • Bathtub Private Faucet 1.0 1.0 1.4
  • Bathtub Public Faucet 3.0 3.0 4.0
  • Bidet Private Faucet 1.5 1.5 2.0
  • Combination fixture Private Faucet 2.25 2.25 3.0
  • Dishwashing machine Private Automatic - 1.4 1.4
  • Drinking fountain Offices, etc. 3/8-inch valve 0.25 - 0.25
  • Kitchen sink Private Faucet 1.0 1.0 1.4
  • Kitchen sink Hotel, restaurant Faucet 3.0 3.0 4.0
  • Laundry trays (1 to 3) Private Faucet 1.0 1.0 1.4
  • Lavatory Private Faucet 0.5 0.5 0.7
  • Lavatory Public Faucet 1.5 1.5 2.0
  • Service sink Offices, etc. Faucet 2.25 2.25 3.0
  • Shower head Private Mixing valve 1.0 1.0 1.4
  • Shower head Public Mixing valve 3.0 3.0 4.0
  • Urinal Public 1-inch flushometer valve 10.0 - 10.0
  • Urinal Public 3/4-inch flushometer valve 5.0 - 5.0
  • Urinal Public Flush tank 3.0 - 3.0
  • Washing machine (8 lb) Private Automatic 1.0 1.0 1.4
  • Washing machine (8 lb) Public Automatic 2.25 2.25 3.0
  • Washing machine (15 lb) Public Automatic 3.0 3.0 4.0
  • Water closet Private Flush tank 2.2 - 2.2
  • Water closet Private Flushometer valve 6.0 - 6.0
  • Water closet Public Flush tank 5.0 - 5.0
  • Water closet Public Flushometer valve 10.0 - 10.0
  • Water closet Public or private Flushometer tank 2.0 - 2.0

A hose bibb or sillcock is not a listed row in Table E103.3(2). Footnote a directs you to assume a load for an unlisted fixture by comparing it to a listed fixture using water in similar quantities and at similar rates; approving authorities in Michigan commonly accept 2.5 wsfu for the first sillcock and 1.0 wsfu for each additional one, but that is a convention, not a printed code value.

Minimum fixture supply pipe sizes are listed separately in MPC Table 604.5 - for example 3/8 inch for a lavatory or flush-tank water closet, 1/2 inch for a bathtub, shower, kitchen sink or dishwasher, 3/4 inch for a flushometer urinal, and 1 inch for a flushometer-valve water closet.

Exam Sizing Rule: Table E103.3(2) lists separate cold and hot values instead of splitting the total in half. For most two-temperature fixtures the cold value and the hot value are each about 75% of the listed total , because either side can carry nearly the whole demand when used alone. Use the printed cold and hot columns; do not derive them by halving the total.

4. Converting WSFU to Design Flow Rate (Gallons Per Minute - GPM)

Once the accumulated WSFU load for a building or branch is totaled, the plumber must convert fixture units into an actual volumetric design flow rate (GPM) to size the service pipe, water meter, and distribution mains.

Because of the hydraulic disparity between gravity flush tanks and pressure-actuated flushometer valves, Hunter established two distinct demand curves in MPC Appendix E (Table E103.3(3)): +-------------------------------------------------------------------------+

  • | WSFU TO GPM CONVERSION COMPARISON |
  • | |
  • | WSFU Load | System with Flush Tanks | System with Flushometers |
  • |:--------------:|:---------------------------:|:-------------------------:|
  • | 1 WSFU | 3.0 GPM | - |
  • | 2 WSFU | 5.0 GPM | - |
  • | 4 WSFU | 8.0 GPM | - |
  • | 5 WSFU | 9.4 GPM | 15.0 GPM |
  • | 10 WSFU | 14.6 GPM | 27.0 GPM |
  • | 20 WSFU | 19.6 GPM | 35.0 GPM |
  • | 30 WSFU | 23.3 GPM | 42.0 GPM |
  • | 40 WSFU | 26.3 GPM | 46.0 GPM |
  • | 50 WSFU | 29.1 GPM | 50.0 GPM |
  • | 70 WSFU | 35.0 GPM | 58.0 GPM |
  • | 100 WSFU | 43.5 GPM | 67.5 GPM |
  • | 200 WSFU | 65.0 GPM | 90.0 GPM |
  • | 300 WSFU | 85.0 GPM | 108.0 GPM |
  • | 500 WSFU | 124.0 GPM | 143.0 GPM |
  • | 1,000 WSFU | 208.0 GPM | 208.0 GPM |
  • +-------------------------------------------------------------------------+

The flushometer column begins at 5 WSFU as printed in Table E103.3(3), and the two columns converge at 1,000 WSFU. Where a calculated load falls between printed rows, read up to the next printed load (or interpolate, if the code official accepts interpolation).

Why Flushometer Systems Demand Higher Initial Capacity

A critical exam concept is understanding why a flushometer system requires substantially greater flow than a flush tank system at low-to-medium WSFU loads:

Operating Dynamics: A standard gravity water closet tank fills through a ballcock/fill valve at a gentle rate of 3 to 5 GPM over a duration of 60 to 90 seconds. In stark contrast, a commercial diaphragm or piston flushometer valve discharges 25 to 35 GPM in a violent 5- to 10-second blast directly from the supply main to scour the bowl and initiate siphonic trap action.

The Single Flushometer Impact: A small commercial office with one public flushometer water closet (10 WSFU) and one public lavatory (2 WSFU) already carries about 11.5 cold WSFU, and Table E103.3(3) puts the design demand near 28 to 29 GPM the moment that single flush valve opens.

Curve Convergence at High Loads: As the connected load grows to hundreds of fixture units (such as a 20-story hotel or major hospital), the flush tank curve and flushometer curve converge, and Table E103.3(3) shows them as identical at and above 1,000 WSFU . In very large buildings, the law of large numbers smooths out the peak surges, so total probabilistic demand is dominated by continuous base load rather than individual valve activations.

5. Minimum Water Service Size (MPC Section 605.3)

The water service pipe is defined by code as the pipe extending from the public water main, water meter, or private well pressure tank to the main building shutoff valve or inside of the foundation wall.

The 3/4-Inch Statutory Floor

Under MPC Section 603.1 , the Michigan Plumbing Code establishes a strict, non-negotiable minimum diameter (Section 605.3 is the separate table of approved water service materials ): Minimum Water Service Diameter = 3/4 Inch (19.1 mm)

No Exceptions for Low WSFU: Even if a tiny single-fixture utility outbuilding calculates out to only 2 or 3 WSFU (which hydraulically might theoretically pass through a 1/2-inch line), the water service pipe buried underground must never be less than 3/4-inch nominal size.

Engineering Rationale: Underground water service lines typically span long distances from the street (50 to 150+ feet). Sizing smaller than 3/4-inch induces severe friction head loss, velocity spikes exceeding code limits, and vulnerability to mechanical damage from soil settlement.

Trench Separation (MPC 603.2): Where a water service pipe and a building sewer share a trench, the sewer must be constructed of materials listed in Table 702.2, or the water service must be separated from the sewer by not less than 5 feet of undisturbed or compacted earth. Where the two cross, the water service must be sleeved to a point 5 feet horizontally from the sewer centerline on both sides.

Sizing Procedure for Water Service Piping

To size the water service beyond the 3/4-inch minimum, plumbers must apply the step-by-step procedure in MPC Appendix E:

Total all connected cold and hot Water Supply Fixture Units (WSFU).

Determine whether the system utilizes flush tanks or flushometer valves.

Convert total WSFU to design flow rate in GPM using MPC Table E103.3(3).

Determine total developed length from public main to the building control valve.

Establish minimum available static street pressure.

Subtract static head losses due to elevation gain (0.433 psi/ft).

Subtract pressure drop through the water meter and backflow preventer.

Apply friction loss charts (Hazen-Williams formula) to select the pipe size that keeps velocity under 8 feet per second (fps) and maintains required residual pressure.

6. Realistic Exam Scenario: Commercial Office Water Service Sizing

Exam Scenario: A journeyman plumber is tasked with sizing the incoming water service for a new single-story commercial office building in Lansing. The plumbing fixtures comprise:

  • 4 Commercial Water Closets with Flushometer Valves (Public)
  • 2 Wall-Hung Urinals with Flushometer Valves (Public)
  • 4 Lavatories (Public)
  • 1 Service Sink / Mop Basin (Public)
  • 1 Exterior Frost-Proof Hose Bibb (First Outlet)

What is the total cold water WSFU load, what is the design flow rate in GPM, and what is the minimum code-permitted water service size?

Code Sizing Walkthrough:

Tabulate Cold-Water Fixture Unit Loads (MPC Table E103.3(2)):

4 public flushometer-valve water closets: 4 × 10.0 = 40.0 4 \times 10.0 = 40.0 4 × 10.0 = 40.0 WSFU (cold only)

  • 2 public 3/4-inch flushometer urinals: 2 × 5.0 = 10.0 2 \times 5.0 = 10.0 2 × 5.0 = 10.0 WSFU (cold only)
  • 4 public lavatories: cold column 1.5 each → 4 × 1.5 = 6.0 \rightarrow 4 \times 1.5 = 6.0 → 4 × 1.5 = 6.0 WSFU
  • 1 public service sink: cold column 2.25 → 2.25 \rightarrow 2.25 → 2.25 WSFU
  • 1 hose bibb (first outlet): 2.5 WSFU (cold only)
  • Total Cold Water Supply Fixture Units: Total Cold WSFU = 40.0 + 10.0 + 6.0 + 2.25 + 2.5 = 60.75 WSFU

Convert to Design GPM (MPC Table E103.3(3), flushometer column):

  • 60 WSFU = 54.0 GPM
  • 70 WSFU = 58.0 GPM

Reading up to the next printed load gives a design demand of 58 GPM ; straight-line interpolation at 60.75 WSFU gives about 54.3 GPM .

Service Size Determination:

The absolute minimum under MPC 603.1 is 3/4 inch, but 3/4-inch tube carrying 54 to 58 GPM would run far past the 8 fps design velocity limit.

Working the friction-loss charts at 8 fps, roughly 2 inches of copper or equivalent is required to carry 54 to 58 GPM, which shows that hydraulic demand - not the 3/4-inch floor - governs the final service size.