Study guide
1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education
Minnesota Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Minnesota Exam, Licensing & Electrical Law
1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement
2 Electrical Theory, Math & Power Calculations
2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting
3 NEC Structure & General Requirements
3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)
4 Conductors, Identification & Ampacity
4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors
5 Branch Circuits, GFCI/AFCI & Required Outlets
5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)
6 Load Calculations (2026 NEC Article 120)
6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)
7 Feeders, Outside Wiring & Services
7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)
8 Overcurrent Protection
8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction
9 System Grounding & Grounding Electrodes
9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems
10 Bonding & Equipment Grounding
10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding
11 General Wiring Methods & Underground Installations
11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)
12 Raceways, Cables & Conduit Fill
12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)
13 Boxes, Conduit Bodies & Cabinets
13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)
14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances
14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)
15 Motors, Controllers & Air Conditioning
15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)
16 Transformers, Generators & Equipment Over 1000 Volts
16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)
17 Hazardous (Classified) Locations
17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)
18 Health Care, Assembly, Agricultural & Mobile Occupancies
18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)
19 Signs, Elevators, Pools, Solar & Other Specific Equipment
19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)
20 Emergency, Standby & Interconnected Power Sources
20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)
21 Limited-Energy, Fire Alarm & Communications Systems
21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)
1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education
Key Takeaways Explain This Topic AI
Minnesota Rules part 3800.3520, subpart 5, item B requires 48 months of experience for the Class A journeyworker license, including at least 24 months of wiring for and installing electrical equipment.
Experience earned in Minnesota after January 1, 2009, counts toward a license only if the worker was registered with or licensed by DLI (Minn. Stat. 326B.33, subd. 13).
Minnesota has journeyworker reciprocity with Alaska, Arkansas, Colorado, Iowa, Montana, Nebraska, North Dakota, South Dakota, and Wyoming.
A Class A journeyworker who has held the license at least 24 months must earn 16 hours of approved continuing education per renewal, at least 12 of them on the NEC.
DLI lists a $53 journeyworker renewal fee, a $20 late fee, and a $19 renewal fee for a registered unlicensed individual.
Last updated: October 2026
Why these rules matter to a candidate
Before you can sit for the exam, DLI must accept your experience. After you pass, you must renew on time with the right continuing education (CE) or you lose the right to work. These rules live in Minnesota Rules chapter 3800 and Minn. Stat. 326B.33 and 326B.092 , all in the exam booklet. They also produce straightforward exam questions with exact numbers.
The journeyworker experience schedule
Minnesota Rules part 3800.3520, subpart 5, item B sets the minimum experience for a Class A journeyworker at 48 months total . Each category has a minimum and a maximum credit:
- Category of experience Minimum Maximum credit
- Planning for installation 0 0
- Laying out for installation 0 0
- Supervising installation 0 0
- Wiring for and installing electrical wiring, apparatus, and equipment 24 months 48 months
- Maintaining and repairing 0 24 months
- Line work 0 3 months
- Installing elevators 0 6 months
- Technology circuits or systems 0 6 months
- Process control circuits or systems 0 12 months
- Approved two-year post-high-school electrical course — 1 year
DLI's Work Experience Verification Form expresses the same requirement as 48 months (8,000 hours) with 2 years of electrical installation . Because planning, layout, and supervision carry zero credit for this license, a journeyworker applicant must build the 48 months from hands-on work, with at least half of it in wiring and installing.
The two-year program credit
Both the statute (326B.33, subd. 2(b)) and the rule allow one year of credit for successfully completing a two-year post-high-school electrical program approved by the department . DLI's exam guide adds that the program must have been approved before you completed it; DLI does not approve programs for individual applicants. An applicant with the credit still needs 36 months of acceptable work experience.
Limits on credit (subpart 3)
No credit for experience before age 17 .
At most 12 months for experience in foreign countries .
No credit for work during the school term of a department-approved two-year program or other full-time daily program. You cannot count the same months as both school credit and field experience.
Acceptable situations (subpart 4)
Experience counts when earned:
while employed by a contractor licensed under 326B.33, subdivision 14;
in Minnesota for an employer not required to be licensed, if the work was inspected under 326B.36 and done under a properly licensed electrician's supervision;
outside Minnesota , when DLI finds it substantially equivalent based on the employer's certification; or
in the armed forces , when DLI finds it substantially equivalent based on military certification. DLI asks military applicants to include a DD214.
Registration of unlicensed individuals
Section 326B.33, subdivision 13 requires unlicensed individuals who perform electrical work for a contractor or employer to register with DLI. It adds the rule that most often decides eligibility disputes: experience for work performed in Minnesota after January 1, 2009, is not credited if the applicant was not registered with or licensed by the department at the time.
Minnesota Rules part 3800.3525 and DLI's registration page fill in the details:
Registrants must be at least 17 and must register before performing work that requires a license.
Required information must be kept current, with changes reported within 30 days .
Renewal requires verification of employment during the prior year and two hours of approved NEC CE .
A registrant must carry the registration card while working and show it on request.
DLI fees are $14 for a new registration, $19 to renew before expiration, and $24 to renew or reinstate an expired registration.
A registration lasts one year and expires on the last day of the month. A registrant who has not renewed within 12 months after expiration must file a new initial application.
Reciprocity
Under 326B.33, subdivision 20 , DLI may issue a personal license without examination under a board-approved reciprocity agreement. Minnesota's journeyworker agreements cover Alaska, Arkansas, Colorado, Iowa, Montana, Nebraska, North Dakota, South Dakota, and Wyoming . Holders of the equivalent of a Minnesota master license in those states may also obtain the Minnesota journeyworker license. Master-level agreements exist with Iowa, North Dakota, Nebraska, and South Dakota. Wisconsin is not on the list.
Conditions in the statute and DLI's guide include:
The license in the other state was obtained by state-level examination , not through a city or another reciprocity agreement.
The applicant held it continuously for at least one year and it is current and in good standing.
The applicant has not failed the same or a greater class of Minnesota exam, and no Minnesota order denies, suspends, or revokes an electrical license.
The applicant pays the $50 application and examination fee, then the license fee after approval.
Renewal and fees
- License or registration Term DLI renewal fee Late fee
- Class A journeyworker 2 years from original issuance (expires end of the month issued) $53 $20
- Class A master Expires last day of February in odd-numbered years $93 $40
- Registered unlicensed individual 1 year $19 $5 (DLI lists $24 to renew an expired registration)
Section 326B.092 builds these fees: a journeyworker-class base fee of $40 for two years, an $8 board fee, and a $5 CE fee on renewal, for $53. It also sets the late fee at one-half of the license renewal fee ; DLI lists a $20 late fee for a journeyworker renewal. A renewal received within two years after expiration must include renewal fees for the lapsed period plus the late fee. DLI states that a Minnesota license not renewed within two years after expiration cannot be regained through reciprocity; the holder must retake and pass the exam.
Warning
An expired license is not a license. Working after the expiration date is unlicensed electrical work under the Act, and the employer can be penalized too.
Continuing education (Minn. R. 3800.3600 to 3800.3603)
Who: DLI will not renew an electrician license for a holder who has held it at least 24 months without the required CE (3800.3602, subp. 1). DLI's guide adds that master electricians need no CE in their first prorated term.
How much: Class A and B master, Class A and B journeyworker, maintenance electrician, and installers need 16 hours per renewal. At least 12 hours must be on the NEC . The remainder may be on electrical statutes and rules (chapters 3800 and 3801 and 326B.31 to 326B.399) or technical topics related to electrical installations. Power limited technicians need 16 hours with at least 4 on the NEC. Registered unlicensed individuals need 2 hours on the NEC every year.
Approved programs only: Programs must be approved by DLI before presentation. Approved programs from other states can count if the other state's electrical licensing authority approved them.
No partial credit: You must complete the entire program.
Use once per license: A credit may be used once for a given renewal, but the same credit may be applied to each type of license you hold. Extra hours do not carry over.
Certificates: Providers must give certificates and report attendance to DLI within 14 days . Keep your certificates.
Worked example
A journeyworker licensed 26 months ago completed an 8-hour NEC update course, a 4-hour course on the Minnesota Electrical Act and chapter 3800, and a 4-hour motor-controls technical course. Total hours are 8 + 4 + 4 = 16, but only 8 are on the NEC. Because at least 12 of the 16 hours must be NEC hours, the electrician still needs 4 more hours of NEC instruction before renewing. The rules-and-statutes course and the technical course both count only toward the remaining 4 hours.