Study guide

1.6 Electrical Permits, Inspections, Condemnation & Enforcement

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

1.6 Electrical Permits, Inspections, Condemnation & Enforcement

Key Takeaways Explain This Topic AI

Minn. Stat. 326B.36, subd. 4 requires a request for inspection, with fees, at or before the start of any installation that must be inspected.

Minnesota Rules part 3801.3770 requires notice to the inspector before wiring is concealed; whoever covers uninspected wiring without adequate notice pays the cost of uncovering and replacing the cover material.

Electrical permits with inspection fees of $1,000 or less are void 12 months after filing, and unfinished work needs a new permit (Minn. R. 3801.3780).

An aggrieved party may appeal an inspector's condemnation or disconnection order within 10 days.

Minn. Stat. 326B.082 allows administrative penalties of up to $10,000 per violation, and the order becomes final unless a hearing is requested within 30 days.

Last updated: October 2026

Why inspection law is on the exam

Every Minnesota installation is checked against the 2026 NEC by a state or local inspector. The exam tests who files the permit, when, what must be inspected, what inspectors may order, and what penalties apply. These rules come from Minn. Stat. 326B.36 (inspection), Minnesota Rules chapter 3801 (procedures), and 326B.082 (enforcement).

What must be inspected

Under 326B.36, subdivision 1 , every new installation in construction, remodeling, replacement, or repair must be inspected for compliance with accepted standards. The exception is minor repair work , which chapter 3800 defines as adjusting, repairing, or replacing worn or defective parts of electrical equipment and replacing defective receptacle outlets and manual lighting switches. The commissioner inspects unless a political subdivision (city, county, or township) or the University of Minnesota provides similar inspection by ordinance. Before filing, check DLI's electrical inspector directory: if the authority having jurisdiction (AHJ) is "State," file with DLI; if it is "Local," contact the city or township.

Technology systems that require inspection (subdivision 2)

Most Class 2 and Class 3 work is exempt from inspection, but these technology circuits must be inspected:

Class 2 or 3 remote-control circuits that control circuits other than Class 2 or 3, and Class 2 or 3 circuits inside enclosures that also contain physically unprotected other circuits;

  • technology circuits in hazardous (classified) locations ;
  • fire alarm systems , other than in one- or two-family dwellings;

technology circuits in critical care areas of health care facilities, such as nurse call and patient monitoring; and

physical security systems in detention facilities .

"Minor work" on technology systems (adjusting or replacing worn parts) is exempt but may be inspected on request.

Installations exempt from inspection (subdivision 7)

These need no inspection: maintenance work by an employer's exempt maintenance electricians; utility-owned facilities used for the utility function that are not on the load side of the service point; utility street lighting and pole-mounted area lights; facilities under the federal Mine Safety and Health Act ; and elevator wiring on the load side of the elevator disconnect inspected by a licensed elevator inspector.

Filing the request for inspection

The Act calls a permit a request for inspection (326B.31, subd. 26a). Under 326B.36, subdivision 4 , "at or before commencement of any installation required to be inspected," the contractor, installer, special electrician, or owner making the installation must submit a request for inspection with a handling fee and an inspection fee . Contractors apply through DLI's iMS system. Owners who qualify for the owner exemption may apply as homeowners.

DLI reviews each permit and emails the inspection process: contact the contract inspector, schedule an electrical remote virtual inspection if eligible, or use the "Ready for Inspection" online request for state-assigned permits. DLI notes that you cannot request a same-day inspection after 8 a.m. and that the requested time is not guaranteed.

Rough-in and final inspection

Rule Requirement

Rough-in (Minn. R. 3801.3770) Where wiring will be concealed, notify the inspector far enough in advance, excluding Saturdays, Sundays, and holidays, to inspect the wiring method and splicing before concealment

Covering without notice The person responsible for enclosing the wiring pays all costs of uncovering and replacing the cover material

Final (3801.3780, subp. 1) Schedule the final inspection before the wiring is used by the intended user and before the space is occupied

Permit expiration (subp. 2) Permits with inspection fees of $1,000 or less are void 12 months after filing; file a new permit and fee for unfinished work; such fees are not refundable after 12 months

End of authority (subp. 3) Authority to install under a permit ends at final inspection or expiration, whichever comes first

Unpaid fees (subp. 4) DLI will not accept new permits from a contractor, employer, or owner who owes fees on earlier permits

Note

Minnesota has no rule allowing work to start now and file a permit "the next business day." The statute says the request for inspection is due at or before the start of the work.

Condemnation, disconnection, and appeals

If an inspector finds an installation not in compliance with accepted standards, 326B.36, subdivision 4(c) requires a written order to condemn the installation or the noncomplying part, or to order service disconnected , with a copy to the commissioner.

If the installation will seriously and proximately endanger life and property, the order, once approved by the inspector's superior, requires immediate condemnation or disconnection.

In all other cases, the order must give a reasonable opportunity to bring the installation into compliance before condemnation or disconnection takes effect.

Copies go to the property owner and the installer. An aggrieved party may appeal within 10 days after service of the order or its filing with the commissioner, whichever is later.

The utility's duty (subdivision 5)

A utility may not newly connect or reconnect an installation subject to inspection until a certificate is filed with it by the property owner or the licensed electrician directing the work, stating that inspection has been requested and the installation is safe to energize. If a condemnation or disconnection order was issued, the utility also needs a copy of the order dismissing it or approving the installation. For transient projects , the request for inspection must reach DLI at least five days before the scheduled energization.

Local inspection programs (subdivision 6)

A city or the University of Minnesota that does its own inspection must file its ordinance with DLI. It may require contractors to keep a copy of their state license on file but may not charge a license or registration fee . Local inspectors, like state inspectors, must be licensed master or journeyworker electricians and may not have a financial interest in electrical businesses. Contract state inspectors give a $1,000 bond (subdivision 3).

Enforcement by the commissioner (326B.082)

Tool Key facts

Access and subpoenas (subd. 2) Enter premises and inspect records; subpoena testimony and documents; responses due within 30 days if no time is stated

Administrative order (subd. 7) Orders correction or cease and desist and may assess a penalty of up to $10,000 per violation ; the commissioner may forgive part or all of the penalty if the person corrects the violation, or has an acceptable correction plan, by the 31st day

Continuing violation Each day a violation stays uncorrected after a final order's deadline is a separate violation

Hearing (subd. 8) Request in writing within 30 days ; otherwise the order becomes final and is not reviewable

Stop work order (subd. 10) Effective on issuance; served on the person or posted at the site; remains until lifted; hearing may be requested within 30 days

Licensing order (subds. 11–12) Deny, suspend, revoke, or censure a license, with penalties up to $10,000 per violation

Under 326B.083 , when setting a penalty the commissioner considers the factors in section 14.045, subdivision 3 : willfulness, gravity, history of past violations, number of violations, economic benefit gained, and other factors justice requires.

Worked scenario

A remodeler drywalls a kitchen before the state inspector sees the rough-in, and no one gave the inspector notice. Under part 3801.3770 the person responsible for enclosing the wiring pays to open and restore the walls so the inspector can see the wiring method and splices. If the inspector finds a hazard that seriously and proximately endangers life and property, the inspector can order immediate disconnection with a supervisor's approval. The contractor then has 10 days to appeal the order.