Study guide
2.6 Motor Connections, Control Circuits & Troubleshooting
Minnesota Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Minnesota Exam, Licensing & Electrical Law
1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement
2 Electrical Theory, Math & Power Calculations
2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting
3 NEC Structure & General Requirements
3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)
4 Conductors, Identification & Ampacity
4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors
5 Branch Circuits, GFCI/AFCI & Required Outlets
5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)
6 Load Calculations (2026 NEC Article 120)
6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)
7 Feeders, Outside Wiring & Services
7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)
8 Overcurrent Protection
8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction
9 System Grounding & Grounding Electrodes
9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems
10 Bonding & Equipment Grounding
10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding
11 General Wiring Methods & Underground Installations
11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)
12 Raceways, Cables & Conduit Fill
12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)
13 Boxes, Conduit Bodies & Cabinets
13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)
14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances
14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)
15 Motors, Controllers & Air Conditioning
15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)
16 Transformers, Generators & Equipment Over 1000 Volts
16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)
17 Hazardous (Classified) Locations
17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)
18 Health Care, Assembly, Agricultural & Mobile Occupancies
18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)
19 Signs, Elevators, Pools, Solar & Other Specific Equipment
19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)
20 Emergency, Standby & Interconnected Power Sources
20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)
21 Limited-Energy, Fire Alarm & Communications Systems
21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)
2.6 Motor Connections, Control Circuits & Troubleshooting
Key Takeaways Explain This Topic AI
A dual-voltage motor's windings are connected in series for the higher voltage (such as 460 V) and in parallel for the lower voltage (such as 230 V).
Swapping any two line leads of a three-phase motor reverses its rotation.
Three-wire control places a normally open holding contact in parallel with the start button, giving low-voltage protection because the motor stays off after power returns.
A jog function must keep the holding circuit from sealing in, so the motor runs only while the jog button is held.
NEC 430.74 requires motor control circuits to be arranged so an accidental ground in the control circuit will not start the motor or bypass safety shutdown devices.
Last updated: October 2026
Why connections and controls are tested
DLI's knowledge-area table lists motor and transformer connections (115/230 V and 230/460 V connections, wye and delta), motor control circuits (three-wire start-stop, start-stop-jog, control circuit transformers), and troubleshooting common electrical problems for the journeyworker exam. These questions test practical shop knowledge more than code lookups.
Dual-voltage three-phase motors
Most general-purpose motors have nine leads (T1 to T9) and can run on 230 V or 460 V. Each phase has two winding halves. For the higher voltage , the halves are in series ; for the lower voltage , they are in parallel . Always follow the motor's connection diagram, but the standard NEMA connections are:
- Motor type 460 V (high, series) 230 V (low, parallel)
- 9-lead wye L1-T1, L2-T2, L3-T3; tie T4-T7, T5-T8, T6-T9 L1-T1-T7, L2-T2-T8, L3-T3-T9; tie T4-T5-T6
- 9-lead delta L1-T1, L2-T2, L3-T3; tie T4-T7, T5-T8, T6-T9 L1-T1-T6-T7, L2-T2-T4-T8, L3-T3-T5-T9
Connecting the series (high-voltage) arrangement to 230 V puts only half of rated voltage on each winding half, so the motor develops about one-quarter torque and may stall. Connecting the low-voltage arrangement to 460 V doubles the voltage on each winding and burns the motor out quickly.
Single-phase 115/230 V motors
A dual-voltage single-phase motor has two main windings (T1-T2 and T3-T4) and a start winding. For 230 V , the main windings are connected in series (T2 joined to T3). For 115 V , they are connected in parallel (T1 with T3, T2 with T4). The start winding connects across one main-winding section so it always sees about 115 V.
Reversing rotation
Three-phase: interchange any two line leads. Reversing starters use two contactors that swap L1 and L3, with mechanical and electrical interlocks so both cannot close at once.
Single-phase split-phase or capacitor-start: reverse the start winding leads relative to the run winding. Swapping the two line leads does not reverse a single-phase motor.
Wye-delta (star-delta) starting
A motor built to run in delta can be started in wye . In wye, each winding sees 1 ÷ 3 1 \div \sqrt{3} 1 ÷ 3 (58%) of line voltage, so starting current and starting torque drop to about one-third of their across-the-line values. After acceleration, the starter switches the windings to delta. The method requires a six-lead (or 12-lead) motor designed for delta running.
Two-wire and three-wire control
Feature Two-wire control Three-wire control
Pilot device Maintained contact (thermostat, float switch, pressure switch) Momentary start (NO) and stop (NC) pushbuttons
After a power interruption Motor restarts automatically when power returns (low-voltage release) Motor stays off until restarted (low-voltage protection)
Typical use Sump pumps, compressors, unattended fans Machine tools, conveyors, anything that could injure someone on restart
The three-wire start-stop circuit
Read the circuit from L1 (or the control transformer X1) to L2 (X2):
The stop button (normally closed) is in series with everything.
The start button (normally open) is in series after stop.
A normally open auxiliary holding (seal-in) contact of the starter, labeled M, is wired in parallel with the start button .
The starter coil M follows, then the overload relay contact (OL) , normally closed, in series.
Pressing start energizes M; the M auxiliary contact closes and keeps the coil energized after the button is released. Pressing stop, opening an overload contact, or losing control voltage drops out the coil, and the holding contact opens. The motor will not restart until someone presses start again.
Multiple stations: to add pushbutton stations, wire additional start buttons in parallel with each other and stop buttons in series with each other.
Adding jog (inch)
Jogging runs the motor only while a button is held, with no seal-in. Common methods:
A selector switch in series with the holding contact: in the "jog" position it opens the seal-in path, so the start button acts as a jog button.
A jog pushbutton with a normally open contact that energizes the coil and a normally closed contact that opens the holding circuit at the same time.
A control relay arrangement that seals in only for run.
The design goal is the same: during jog, the holding contact must not be able to keep the coil energized.
Control circuit transformers and protection
Control circuits are often fed through a control circuit transformer (CCT) that steps line voltage (such as 480 V) down to 120 V. NEC 430.72 requires overcurrent protection for motor control circuit conductors and for the transformer. Many CCTs have secondary fuses and primary fuses. Section 430.74 requires the control circuit to be arranged so that an accidental ground in the control circuit will not start the motor or bypass manually operated shutdown devices or automatic safety shutdown devices. This is why the coil is typically connected directly to the grounded side (X2) and the switching contacts are placed on the ungrounded side (X1).
Troubleshooting common problems
DLI expects you to reason from symptoms to causes. A practical sequence:
Verify supply voltage at the equipment terminals with the load running. Low voltage under load but normal voltage at no load points to a high-resistance connection or undersized conductors (voltage drop).
Check control voltage at the coil. If the coil is energized and the contactor does not close, the coil or contactor is defective; if there is no coil voltage, trace through the stop, start, overload, and safety contacts.
Check for tripped overloads and find out why: mechanical binding, low voltage, a stalled load, or single-phasing .
Measure current in all three phases. Unequal currents point to unbalanced voltage, a high-resistance connection, or a winding problem. A small voltage imbalance produces a much larger current imbalance and extra heating.
Test insulation with a megohmmeter after locking out and disconnecting the motor. A ground fault shows as low resistance from a winding to the frame.
Classic symptoms
Symptom Likely cause
Lights brighten in one room and dim in another when a large 120 V load starts Open neutral on a multiwire circuit or a 120/240 V service
- Three-phase motor hums, will not start, overheats Single-phasing (one phase open, such as a blown fuse)
- Motor runs backward after a utility repair Phase rotation changed; swap two leads
GFCI trips as soon as a load is plugged in Ground fault in the load or a neutral-to-ground connection downstream
- Breaker warm at the terminal, discolored insulation Loose or improperly torqued termination
- Starter coil chatters Low control voltage or a failing holding contact
Warning
Troubleshooting energized equipment exposes you to shock and arc-flash hazards. NFPA 70E, not the NEC, governs safe work practices such as establishing an electrically safe work condition, lockout/tagout, and arc-flash PPE.