Study guide

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits

Key Takeaways Explain This Topic AI

Ohm's Law defines the relationship between potential difference, current flow, and resistance: V = I × R V = I \times R V = I × R , I = V R I = \frac{V}{R} I = R V ​ , and R = V I R = \frac{V}{I} R = I V ​ .

Watt's Law calculates real electrical power in watts: P = V × I = I 2 × R = V 2 R P = V \times I = I^2 \times R = \frac{V^2}{R} P = V × I = I 2 × R = R V 2 ​ .

In a DC series circuit, current remains constant throughout ( I T = I 1 = I 2 = … I_T = I_1 = I_2 = \dots I T ​ = I 1 ​ = I 2 ​ = … ), resistance is additive ( R T = R 1 + R 2 + … R_T = R_1 + R_2 + \dots R T ​ = R 1 ​ + R 2 ​ + … ), and the sum of individual voltage drops equals source voltage.

In a DC parallel circuit, voltage is identical across every branch ( V T = V 1 = V 2 = … V_T = V_1 = V_2 = \dots V T ​ = V 1 ​ = V 2 ​ = … ), total current is the sum of branch currents ( I T = I 1 + I 2 + … I_T = I_1 + I_2 + \dots I T ​ = I 1 ​ + I 2 ​ + … ), and equivalent resistance is calculated by 1 R T = 1 R 1 + 1 R 2 + … \frac{1}{R_T} = \frac{1}{R_1} + \frac{1}{R_2} + \dots R T ​ 1 ​ = R 1 ​ 1 ​ + R 2 ​ 1 ​ + … or R T = R 1 × R 2 R 1 + R 2 R_T = \frac{R_1 \times R_2}{R_1 + R_2} R T ​ = R 1 ​ + R 2 ​ R 1 ​ × R 2 ​ ​ .

DLI's exam guide lists general mathematics (transposing equations, area, volume, percentages), Ohm's law, Watt's law, and series-parallel circuits for every electrical license exam.

Last updated: October 2026

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits

Every electrical installation governed by the National Electrical Code rests on fundamental physical laws that describe how electrical charges behave under potential difference. For the journeyworker electrician, mastery of direct current (DC) theory is not merely academic—it forms the mathematical foundation for sizing conductors, calculating overcurrent protection, assessing equipment heat dissipation, and troubleshooting field wiring faults.

Fundamentals of Direct Current Theory

Direct current (DC) represents the unidirectional flow of electric charge. Four basic physical quantities govern every DC circuit:

Electromotive Force (Voltage, V V V or E E E ): Measured in volts ( V \text{V} V ), voltage represents the electrical potential difference between two points, providing the pressure that forces free electrons through a conductive medium.

Current ( I I I ): Measured in amperes ( A \text{A} A ), current represents the rate of charge flow through a conductor, where one ampere equals one coulomb of charge moving past a specific cross-section per second ( 1 A = 1 C/s = 6.242 × 10 18 electrons/s 1\text{ A} = 1\text{ C/s} = 6.242 \times 10^{18}\text{ electrons/s} 1 A = 1 C/s = 6.242 × 1 0 18 electrons/s ).

Resistance ( R R R ): Measured in ohms ( Ω \Omega Ω ), resistance represents the opposition a material offers to the movement of free electrons, converting electrical energy into heat.

Power ( P P P ): Measured in watts ( W \text{W} W ), power represents the rate at which electrical energy is transformed into another form of work or heat, where one watt equals one joule per second ( 1 W = 1 J/s 1\text{ W} = 1\text{ J/s} 1 W = 1 J/s ).

The Ohm's Law and Watt's Law Formula Wheel

In 1827, German physicist Georg Simon Ohm verified experimentally that current through a conductor between two points is directly proportional to voltage across the points and inversely proportional to resistance. James Watt established the relationship between potential, current, and mechanical work. Combining Ohm's Law ( V = I × R V = I \times R V = I × R ) and Watt's Law ( P = V × I P = V \times I P = V × I ) yields 12 fundamental algebraic equations.

Desired Quantity Using V V V and I I I Using I I I and R R R Using V V V and R R R Using P P P and R R R Using P P P and I I I Using P P P and V V V

Voltage ( V V V ) — V = I × R V = I \times R V = I × R — V = P × R V = \sqrt{P \times R} V = P × R ​ V = P I V = \frac{P}{I} V = I P ​ —

Current ( I I I ) — — I = V R I = \frac{V}{R} I = R V ​ I = P R I = \sqrt{\frac{P}{R}} I = R P ​ ​ — I = P V I = \frac{P}{V} I = V P ​

Resistance ( R R R ) — — R = V I R = \frac{V}{I} R = I V ​ — R = P I 2 R = \frac{P}{I^2} R = I 2 P ​ R = V 2 P R = \frac{V^2}{P} R = P V 2 ​

Power ( P P P ) P = V × I P = V \times I P = V × I P = I 2 × R P = I^2 \times R P = I 2 × R P = V 2 R P = \frac{V^2}{R} P = R V 2 ​ — — —

DC Series Circuit Analysis

A series circuit provides exactly one continuous, uninterrupted conductive path through which current can flow. Because there are no junction points or alternate paths, every electron leaving the negative power terminal must pass sequentially through every connected load before returning to the source.

The Three Cardinal Laws of Series Circuits

Current is Uniform: Current flow is identical at every point in the series string: I T = I 1 = I 2 = I 3 = ⋯ = I n I_T = I_1 = I_2 = I_3 = \dots = I_n I T ​ = I 1 ​ = I 2 ​ = I 3 ​ = ⋯ = I n ​

Resistance is Additive: Total circuit resistance equals the arithmetic sum of individual component resistances: R T = R 1 + R 2 + R 3 + ⋯ + R n R_T = R_1 + R_2 + R_3 + \dots + R_n R T ​ = R 1 ​ + R 2 ​ + R 3 ​ + ⋯ + R n ​

Kirchhoff's Voltage Law (KVL): The algebraic sum of all voltages around any closed loop must equal zero. In practice, the total source voltage equals the sum of the individual component voltage drops: V T = V 1 + V 2 + V 3 + ⋯ + V n V_T = V_1 + V_2 + V_3 + \dots + V_n V T ​ = V 1 ​ + V 2 ​ + V 3 ​ + ⋯ + V n ​

The Voltage Divider Principle

Because current is identical through all series elements, the voltage dropped across any single resistor is directly proportional to its share of the total resistance:

  • V x = V T × ( R x R T ) V_x = V_T \times \left(\frac{R_x}{R_T}\right) V x ​ = V T ​ × ( R T ​ R x ​ ​ )
  • Step-by-Step Series Circuit Calculation

Consider an industrial control circuit powered by a 120 V 120\text{ V} 120 V DC supply connected to three series resistors: R 1 = 15 Ω R_1 = 15\ \Omega R 1 ​ = 15 Ω , R 2 = 25 Ω R_2 = 25\ \Omega R 2 ​ = 25 Ω , and R 3 = 20 Ω R_3 = 20\ \Omega R 3 ​ = 20 Ω .

Calculate Total Resistance ( R T R_T R T ​ ): R T = 15 Ω + 25 Ω + 20 Ω = 60 Ω R_T = 15\ \Omega + 25\ \Omega + 20\ \Omega = 60\ \Omega R T ​ = 15 Ω + 25 Ω + 20 Ω = 60 Ω

Calculate Total Circuit Current ( I T I_T I T ​ ): I T = V T R T = 120 V 60 Ω = 2.0 A I_T = \frac{V_T}{R_T} = \frac{120\text{ V}}{60\ \Omega} = 2.0\text{ A} I T ​ = R T ​ V T ​ ​ = 60 Ω 120 V ​ = 2.0 A

Calculate Individual Voltage Drops ( V 1 , V 2 , V 3 V_1, V_2, V_3 V 1 ​ , V 2 ​ , V 3 ​ ):

V 1 = I T × R 1 = 2.0 A × 15 Ω = 30 V V_1 = I_T \times R_1 = 2.0\text{ A} \times 15\ \Omega = 30\text{ V} V 1 ​ = I T ​ × R 1 ​ = 2.0 A × 15 Ω = 30 V

V 2 = I T × R 2 = 2.0 A × 25 Ω = 50 V V_2 = I_T \times R_2 = 2.0\text{ A} \times 25\ \Omega = 50\text{ V} V 2 ​ = I T ​ × R 2 ​ = 2.0 A × 25 Ω = 50 V

V 3 = I T × R 3 = 2.0 A × 20 Ω = 40 V V_3 = I_T \times R_3 = 2.0\text{ A} \times 20\ \Omega = 40\text{ V} V 3 ​ = I T ​ × R 3 ​ = 2.0 A × 20 Ω = 40 V

Verification: 30 V + 50 V + 40 V = 120 V 30\text{ V} + 50\text{ V} + 40\text{ V} = 120\text{ V} 30 V + 50 V + 40 V = 120 V (KVL confirmed).

Calculate Power Dissipation:

P 1 = I 2 × R 1 = ( 2.0 ) 2 × 15 = 60 W P_1 = I^2 \times R_1 = (2.0)^2 \times 15 = 60\text{ W} P 1 ​ = I 2 × R 1 ​ = ( 2.0 ) 2 × 15 = 60 W

P 2 = I 2 × R 2 = ( 2.0 ) 2 × 25 = 100 W P_2 = I^2 \times R_2 = (2.0)^2 \times 25 = 100\text{ W} P 2 ​ = I 2 × R 2 ​ = ( 2.0 ) 2 × 25 = 100 W

P 3 = I 2 × R 3 = ( 2.0 ) 2 × 20 = 80 W P_3 = I^2 \times R_3 = (2.0)^2 \times 20 = 80\text{ W} P 3 ​ = I 2 × R 3 ​ = ( 2.0 ) 2 × 20 = 80 W

Total Power: P T = 60 + 100 + 80 = 240 W P_T = 60 + 100 + 80 = 240\text{ W} P T ​ = 60 + 100 + 80 = 240 W (Or P T = V T × I T = 120 × 2.0 = 240 W P_T = V_T \times I_T = 120 \times 2.0 = 240\text{ W} P T ​ = V T ​ × I T ​ = 120 × 2.0 = 240 W ).

DC Parallel Circuit Analysis

A parallel circuit connects two or more electrical loads between the same pair of common electrically common nodes. Parallel wiring is the standard distribution topology for premises wiring because every branch load operates at full system voltage regardless of the presence, operation, or failure of other connected loads.

The Three Cardinal Laws of Parallel Circuits

Voltage is Uniform: Every parallel branch experiences the exact same potential difference: V T = V 1 = V 2 = V 3 = ⋯ = V n V_T = V_1 = V_2 = V_3 = \dots = V_n V T ​ = V 1 ​ = V 2 ​ = V 3 ​ = ⋯ = V n ​

Kirchhoff's Current Law (KCL): The total current entering a junction equals the total current leaving the junction. Total circuit current equals the sum of branch currents: I T = I 1 + I 2 + I 3 + ⋯ + I n I_T = I_1 + I_2 + I_3 + \dots + I_n I T ​ = I 1 ​ + I 2 ​ + I 3 ​ + ⋯ + I n ​

Reciprocal Equivalent Resistance: Adding parallel paths increases the cross-sectional conductive area available to current, meaning total equivalent resistance is always strictly less than the smallest individual branch resistance: 1 R T = 1 R 1 + 1 R 2 + 1 R 3 + ⋯ + 1 R n \frac{1}{R_T} = \frac{1}{R_1} + \frac{1}{R_2} + \frac{1}{R_3} + \dots + \frac{1}{R_n} R T ​ 1 ​ = R 1 ​ 1 ​ + R 2 ​ 1 ​ + R 3 ​ 1 ​ + ⋯ + R n ​ 1 ​

Specialized Parallel Resistance Shortcuts

Two Resistors in Parallel (Product Over Sum): R T = R 1 × R 2 R 1 + R 2 R_T = \frac{R_1 \times R_2}{R_1 + R_2} R T ​ = R 1 ​ + R 2 ​ R 1 ​ × R 2 ​ ​

  • n n n Identical Resistors in Parallel: R T = R n R_T = \frac{R}{n} R T ​ = n R ​
  • The Current Divider Principle

When current divides between two parallel branches, branch current is inversely proportional to branch resistance:

I 1 = I T × ( R 2 R 1 + R 2 ) I_1 = I_T \times \left(\frac{R_2}{R_1 + R_2}\right) I 1 ​ = I T ​ × ( R 1 ​ + R 2 ​ R 2 ​ ​ )

Step-by-Step Parallel Circuit Calculation

A 240 V 240\text{ V} 240 V DC supply feeds three parallel heating elements: R 1 = 20 Ω R_1 = 20\ \Omega R 1 ​ = 20 Ω , R 2 = 30 Ω R_2 = 30\ \Omega R 2 ​ = 30 Ω , and R 3 = 60 Ω R_3 = 60\ \Omega R 3 ​ = 60 Ω .

Calculate Total Equivalent Resistance ( R T R_T R T ​ ): 1 R T = 1 20 + 1 30 + 1 60 = 3 + 2 + 1 60 = 6 60 = 1 10 Ω \frac{1}{R_T} = \frac{1}{20} + \frac{1}{30} + \frac{1}{60} = \frac{3 + 2 + 1}{60} = \frac{6}{60} = \frac{1}{10\ \Omega} R T ​ 1 ​ = 20 1 ​ + 30 1 ​ + 60 1 ​ = 60 3 + 2 + 1 ​ = 60 6 ​ = 10 Ω 1 ​ R T = 10 Ω R_T = 10\ \Omega R T ​ = 10 Ω

Calculate Branch Currents ( I 1 , I 2 , I 3 I_1, I_2, I_3 I 1 ​ , I 2 ​ , I 3 ​ ):

  • I 1 = 240 V 20 Ω = 12 A I_1 = \frac{240\text{ V}}{20\ \Omega} = 12\text{ A} I 1 ​ = 20 Ω 240 V ​ = 12 A
  • I 2 = 240 V 30 Ω = 8 A I_2 = \frac{240\text{ V}}{30\ \Omega} = 8\text{ A} I 2 ​ = 30 Ω 240 V ​ = 8 A
  • I 3 = 240 V 60 Ω = 4 A I_3 = \frac{240\text{ V}}{60\ \Omega} = 4\text{ A} I 3 ​ = 60 Ω 240 V ​ = 4 A

Calculate Total Circuit Current ( I T I_T I T ​ ): I T = 12 A + 8 A + 4 A = 24 A I_T = 12\text{ A} + 8\text{ A} + 4\text{ A} = 24\text{ A} I T ​ = 12 A + 8 A + 4 A = 24 A

Verification using Ohm's Law: I T = 240 V 10 Ω = 24 A I_T = \frac{240\text{ V}}{10\ \Omega} = 24\text{ A} I T ​ = 10 Ω 240 V ​ = 24 A (KCL confirmed).

Calculate Power Dissipation:

P 1 = 240 V × 12 A = 2 , 880 W P_1 = 240\text{ V} \times 12\text{ A} = 2,880\text{ W} P 1 ​ = 240 V × 12 A = 2 , 880 W

P 2 = 240 V × 8 A = 1 , 920 W P_2 = 240\text{ V} \times 8\text{ A} = 1,920\text{ W} P 2 ​ = 240 V × 8 A = 1 , 920 W

P 3 = 240 V × 4 A = 960 W P_3 = 240\text{ V} \times 4\text{ A} = 960\text{ W} P 3 ​ = 240 V × 4 A = 960 W

P T = 2 , 880 + 1 , 920 + 960 = 5 , 760 W = 5.76 kW P_T = 2,880 + 1,920 + 960 = 5,760\text{ W} = 5.76\text{ kW} P T ​ = 2 , 880 + 1 , 920 + 960 = 5 , 760 W = 5.76 kW .

Combination (Series-Parallel) Resistor Networks

Practical field circuits often present combination series-parallel configurations. A classic example is a long branch circuit where the conductor lead resistance sits in series with parallel-connected lighting or receptacle loads.

The Step-by-Step Reduction Method

To solve a complex combination network:

Identify Pure Parallel Clusters: Locate sub-networks of resistors connected across identical nodes and reduce them to single equivalent resistances ( R p R_p R p ​ ).

Identify Pure Series Elements: Locate resistors connected in series with the equivalent blocks and sum them.

Redraw the Simplified Circuit: Repeat reduction until a single equivalent total resistance ( R T R_T R T ​ ) remains.

Calculate Total Circuit Current: Apply Ohm's Law ( I T = V T R T I_T = \frac{V_T}{R_T} I T ​ = R T ​ V T ​ ​ ).

Traverse Backward: Apply Ohm's Law, KVL, and KCL to calculate intermediate node voltages and branch currents.

Worked Example: Combination Circuit Analysis

A 120 V 120\text{ V} 120 V DC power source supplies a series resistor R 1 = 10 Ω R_1 = 10\ \Omega R 1 ​ = 10 Ω connected in line with a parallel bank containing R 2 = 30 Ω R_2 = 30\ \Omega R 2 ​ = 30 Ω and R 3 = 60 Ω R_3 = 60\ \Omega R 3 ​ = 60 Ω .

Reduce the Parallel Bank ( R 2 , 3 R_{2,3} R 2 , 3 ​ ): R 2 , 3 = R 2 × R 3 R 2 + R 3 = 30 × 60 30 + 60 = 1800 90 = 20 Ω R_{2,3} = \frac{R_2 \times R_3}{R_2 + R_3} = \frac{30 \times 60}{30 + 60} = \frac{1800}{90} = 20\ \Omega R 2 , 3 ​ = R 2 ​ + R 3 ​ R 2 ​ × R 3 ​ ​ = 30 + 60 30 × 60 ​ = 90 1800 ​ = 20 Ω

Calculate Total Resistance ( R T R_T R T ​ ): R T = R 1 + R 2 , 3 = 10 Ω + 20 Ω = 30 Ω R_T = R_1 + R_{2,3} = 10\ \Omega + 20\ \Omega = 30\ \Omega R T ​ = R 1 ​ + R 2 , 3 ​ = 10 Ω + 20 Ω = 30 Ω

Calculate Total Current ( I T I_T I T ​ ): I T = V T R T = 120 V 30 Ω = 4.0 A I_T = \frac{V_T}{R_T} = \frac{120\text{ V}}{30\ \Omega} = 4.0\text{ A} I T ​ = R T ​ V T ​ ​ = 30 Ω 120 V ​ = 4.0 A

Calculate Voltage Drop Across Series Resistor R 1 R_1 R 1 ​ : V R 1 = I T × R 1 = 4.0 A × 10 Ω = 40 V V_{R1} = I_T \times R_1 = 4.0\text{ A} \times 10\ \Omega = 40\text{ V} V R 1 ​ = I T ​ × R 1 ​ = 4.0 A × 10 Ω = 40 V

Calculate Voltage Across the Parallel Bank ( V 2 , 3 V_{2,3} V 2 , 3 ​ ): V 2 , 3 = V T − V R 1 = 120 V − 40 V = 80 V V_{2,3} = V_T - V_{R1} = 120\text{ V} - 40\text{ V} = 80\text{ V} V 2 , 3 ​ = V T ​ − V R 1 ​ = 120 V − 40 V = 80 V

Calculate Individual Branch Currents ( I 2 , I 3 I_2, I_3 I 2 ​ , I 3 ​ ):

I 2 = V 2 , 3 R 2 = 80 V 30 Ω ≈ 2.67 A I_2 = \frac{V_{2,3}}{R_2} = \frac{80\text{ V}}{30\ \Omega} \approx 2.67\text{ A} I 2 ​ = R 2 ​ V 2 , 3 ​ ​ = 30 Ω 80 V ​ ≈ 2.67 A

I 3 = V 2 , 3 R 3 = 80 V 60 Ω ≈ 1.33 A I_3 = \frac{V_{2,3}}{R_3} = \frac{80\text{ V}}{60\ \Omega} \approx 1.33\text{ A} I 3 ​ = R 3 ​ V 2 , 3 ​ ​ = 60 Ω 80 V ​ ≈ 1.33 A

Verification: I 2 + I 3 = 2.67 A + 1.33 A = 4.0 A = I T I_2 + I_3 = 2.67\text{ A} + 1.33\text{ A} = 4.0\text{ A} = I_T I 2 ​ + I 3 ​ = 2.67 A + 1.33 A = 4.0 A = I T ​ .

The Math DLI Expects You to Do by Hand

DLI's exam guide lists general mathematics for every license: transposing equations and calculating area, volume, and percentages. Its own worked examples show the level expected:

Percent of a number: 70% of 140 is 140 × 0.70 = 98 140 \times 0.70 = 98 140 × 0.70 = 98 .

Increasing by a percent: increasing 120 by 25% is 120 × 1.25 = 150 120 \times 1.25 = 150 120 × 1.25 = 150 . The same move gives 125% of a continuous load.

Ratios: a 480/120 V transformer has a primary-to-secondary voltage ratio of 480 ÷ 120 = 4 480 \div 120 = 4 480 ÷ 120 = 4 , written 4:1.

Transposing: if A × B = C A \times B = C A × B = C , dividing both sides by B B B gives A = C ÷ B A = C \div B A = C ÷ B . Ohm's law and Watt's law can each be rearranged this way into the other forms in the table above.

Area and volume: box fill uses cubic inches (a 60 cu in box holds 60 ÷ 2.25 = 26.67 60 \div 2.25 = 26.67 60 ÷ 2.25 = 26.67 , so 26 conductors of 12 AWG, because you never round up), and conduit fill uses square inches from Chapter 9.

DLI writes Ohm's law as E = I × R E = I \times R E = I × R , with E for electromotive force in volts. Treat E and V as the same quantity. Unless a question says otherwise, DLI assumes unity power factor , so P = E × I P = E \times I P = E × I for single-phase loads.

DLI's own parallel-resistance examples

  • Method DLI example Result
  • Equal resistors: R T = R ÷ N R_T = R \div N R T ​ = R ÷ N Three 15 Ω resistors 5 Ω
  • Product over sum 20 Ω and 30 Ω 600 ÷ 50 = 12 600 \div 50 = 12 600 ÷ 50 = 12 Ω
  • Reciprocal 2 Ω, 4 Ω, 8 Ω 1 ÷ 0.875 = 1.143 1 \div 0.875 = 1.143 1 ÷ 0.875 = 1.143 Ω

For a series circuit, DLI's example uses 20 Ω, 40 Ω, and 60 Ω carrying 2 A: R T = 120 R_T = 120 R T ​ = 120 Ω and E = 2 × 120 = 240 E = 2 \times 120 = 240 E = 2 × 120 = 240 V.

Comparison Table: Series vs. Parallel Circuits

Parameter Series Circuit Parallel Circuit

Current ( I I I ) Identical through all components ( I T = I 1 = I 2 I_T = I_1 = I_2 I T ​ = I 1 ​ = I 2 ​ ) Sum of branch currents ( I T = I 1 + I 2 I_T = I_1 + I_2 I T ​ = I 1 ​ + I 2 ​ )

Voltage ( V V V ) Sum of individual drops equals source ( V T = V 1 + V 2 V_T = V_1 + V_2 V T ​ = V 1 ​ + V 2 ​ ) Identical across all branches ( V T = V 1 = V 2 V_T = V_1 = V_2 V T ​ = V 1 ​ = V 2 ​ )

Total Resistance ( R T R_T R T ​ ) Additive ( R T = R 1 + R 2 R_T = R_1 + R_2 R T ​ = R 1 ​ + R 2 ​ ), greater than largest R R R Reciprocal, strictly less than smallest branch R R R

Component Failure An open circuit halts current to all components An open branch affects only that branch

Practical Applications Control safety interlocks, thermal cutoffs, switches General receptacle circuits, building lighting, motor banks