Study guide

5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

Key Takeaways Explain This Topic AI

In dwelling habitable rooms, receptacles must be placed so no point along the floor line of any wall space 2 ft or wider is more than 6 ft from a receptacle outlet (210.52(A)).

Wall countertops 12 in. or wider need receptacles so that no point along the wall line is more than 24 in. from one (210.52(C)(1)).

An island or peninsula does not require a receptacle, but if none is installed, provisions for a future receptacle outlet must be provided (210.52(C)(2)).

Dwellings need at least two 20 A small-appliance circuits, one 20 A laundry circuit, one 20 A bathroom receptacle circuit, and one 20 A garage receptacle circuit (210.11(C)).

Interior stairways with six or more risers between floor levels need a wall-mounted control at each floor level and each landing level with an entryway (210.70(A)(2)).

Last updated: October 2026

Why placement rules are tested

DLI's knowledge areas include required outlets and circuits for dwellings. The rules are prescriptive: a question gives room dimensions, and you count receptacles or circuits. Read carefully, because the 2023 and 2026 editions changed the island, peninsula, and below-countertop rules that older study materials still teach.

Required dwelling branch circuits (210.11(C))

Circuit Requirement What else it may serve

Small-appliance Two or more 20 A circuits for receptacles in the kitchen, pantry, breakfast room, dining room, or similar area No other outlets, except an electric clock receptacle and receptacles for supplemental equipment and lighting on gas-fired ranges, ovens, or counter-mounted cooking units

Laundry At least one 20 A circuit for the laundry receptacles required by 210.52(F) No other outlets

Bathroom At least one 120 V, 20 A circuit for bathroom receptacles No other outlets, except that a circuit serving a single bathroom may also supply other equipment in that bathroom

Garage At least one 120 V, 20 A circuit for receptacles in attached garages and detached garages with power No other outlets, except readily accessible outdoor receptacles

The countertop receptacles in a kitchen must be supplied by at least two small-appliance circuits, and no small-appliance circuit may serve more than one kitchen (210.52(B)(3)). The refrigerator receptacle may be on a small-appliance circuit or on an individual branch circuit rated 15 A or more (210.52(B)(1) Exception No. 2).

General wall receptacles (210.52(A))

In kitchens, family rooms, dining rooms, living rooms, parlors, libraries, dens, sunrooms, bedrooms, recreation rooms, and similar rooms:

Spacing: no point measured horizontally along the floor line in any wall space may be more than 6 ft from a receptacle outlet in that space, so receptacles can be up to 12 ft apart.

Wall space includes any space 2 ft or more wide (measured around corners) and unbroken along the floor line by doorways, fireplaces, and fixed cabinets; fixed panels in walls (excluding sliding panels); and fixed room dividers such as freestanding bar-type counters or railings. The 2026 NEC excludes any fixed cabinet from wall space; the 2023 edition excluded only fixed cabinets without countertops or similar work surfaces.

Floor receptacles count only if within 18 in. of the wall.

Countertop receptacles required by 210.52(C) do not count toward the wall requirement.

Not counted at all: receptacles that are part of a luminaire or appliance, inside cabinets, controlled by a wall-mounted control device (except where used in place of a lighting outlet), or more than 5½ ft above the floor.

2026 NEC 210.52(A)(5): receptacle outlets may be installed on the walls of cabinets that support a countertop or work surface, such as a bar-type counter, only if they are at least 24 in. below the countertop surface.

Countertops and work surfaces (210.52(C))

Rule Requirement

Wall countertops (C)(1) A receptacle at each wall counter space 12 in. or wider ; no point along the wall line more than 24 in. from a receptacle

Behind a sink or range Space behind a range, counter-mounted cooking unit, or sink is treated as described in the figure for 210.52(C)(1); a receptacle is not required directly behind them

Islands and peninsulas (C)(2) A receptacle is not required ; if none is installed, provisions for a future receptacle outlet must be provided at the island or peninsula

Location (C)(3) On or above the countertop, not more than 20 in. above it, or in the countertop using receptacle outlet assemblies listed for countertop use

Not counted Receptacles made not readily accessible by fastened-in-place appliances, appliance garages, sinks, or rangetops

2026 NEC (C)(4) Receptacle outlets are not permitted within 24 in. below the countertop surface, which keeps appliance cords from hanging off islands and peninsulas where children can pull them

Receptacles may not be installed face up in a countertop or work surface unless listed for that application, and the 2026 NEC also prohibits face-up receptacles in laundry areas (Article 406). The 2026 Article 100 definitions distinguish a countertop , which includes food and beverage preparation or serving, from a work surface , which is intended for dry tasks.

Other required receptacle locations

Location Rule

Bathrooms (210.52(D)) At least one receptacle within 3 ft of the outside edge of each basin, on an adjacent wall or partition, on the countertop, or on the side or face of the basin cabinet not more than 12 in. below the countertop; one receptacle between two basins may serve both

Outdoors (210.52(E)) One- and two-family dwellings: one at the front and one at the back , readily accessible from grade and not more than 6½ ft above grade; at-grade multifamily units with an outside entrance: at least one; balconies, decks, and porches accessible from inside: at least one, not more than 6½ ft above the walking surface

Laundry (210.52(F)) At least one receptacle in areas designated for laundry equipment

Garages (210.52(G)) At least one receptacle in each vehicle bay , not more than 5½ ft above the floor; one in each accessory building with power and in each separate unfinished portion of a basement

Hallways (210.52(H)) At least one receptacle in a hallway 10 ft or more long, measured along the centerline without passing through a doorway

Foyers (210.52(I)) Foyers over 60 ft² that are not part of a hallway: a receptacle in each wall space 3 ft or more wide

HVAC servicing (210.63(A)) A 125 V, 15 A or 20 A receptacle within 25 ft of HVAC equipment, on the same level, not on the load side of the equipment disconnect; the 2026 NEC 422.12 allows this receptacle to be supplied from a dedicated furnace circuit

Lighting outlets (210.70(A))

Habitable rooms, kitchens, laundry rooms, and bathrooms: at least one lighting outlet controlled by a listed wall-mounted control device near the entrance. A 2026 exception lets the laundry lighting outlet be outside a laundry closet if it adequately illuminates the laundry equipment. In rooms other than kitchens and bathrooms, a switched receptacle may replace the lighting outlet. Occupancy sensors are allowed if added to a wall control or installed at the usual switch location with a manual override.

Hallways, stairways, attached garages, and detached garages with power: at least one wall-controlled lighting outlet.

Outdoor entrances: a wall-controlled lighting outlet on the exterior side of each outdoor entrance or exit with grade-level access, including garages with power. A garage vehicle door is not an outdoor entrance for this rule.

Stairways: where the stairway between floor levels has six or more risers , a wall-mounted control at each floor level and each landing level that includes an entryway . Dimmers are not allowed on these controls unless they provide full-range dimming from every location.

Storage and equipment spaces (210.70(C)): attics, underfloor spaces, utility rooms, and basements used for storage or containing equipment requiring servicing need a lighting outlet at or near the equipment, with a point of control at the usual entrance.

Worked example: a living room

A living room wall space runs 10 ft from a doorway to a corner and continues 12 ft along the next wall to a fireplace. Because wall space is measured around corners, this is one continuous 22 ft wall space. On the far side of the fireplace is a 4 ft space ending at a doorway, and between two doors is a 1 ft 6 in. space.

22 ft space: no point may be more than 6 ft from a receptacle, so each receptacle covers 12 ft. Place one 6 ft from the doorway (covering 0 to 12 ft) and one at 18 ft (covering 12 to 24 ft): two receptacles.

4 ft space: the fireplace breaks the wall, so this is a separate wall space 2 ft or wider: one receptacle.

1 ft 6 in. space: less than 2 ft, so it is not a wall space: none.

The room needs at least three receptacle outlets, all on AFCI-protected circuits.