Study guide

6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88)

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88)

Key Takeaways Explain This Topic AI

Commercial kitchen equipment feeder loads are calculated using NEC Table 120.56 demand factors (1-2 units at 100%, 3 units at 90%, 4 units at 80%, 5 units at 70%, and 6 or more units at 65%).

Under NEC 120.56, in no case shall the calculated commercial kitchen feeder demand load be less than the sum of the two largest kitchen equipment loads.

Commercial kitchen demand factors under Table 120.56 apply to electric cooking appliances, dishwashers, water booster heaters, and food warming equipment, but explicitly exclude space heating, ventilating, and air-conditioning loads.

The optional method for schools under NEC 120.86 and Table 120.86 is permitted for institutions with electric space conditioning, calculating demand at 100% of the first 3 VA/sq ft, 75% from 3 to 20 VA/sq ft, and 25% of all load exceeding 20 VA/sq ft.

New restaurants may utilize the optional calculation under NEC 120.88 and Table 120.88, categorizing loads into all-electric versus not all-electric configurations with tiered square footage demand factors.

Last updated: October 2026

6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88)

Quick Answer: Feeder demand for commercial kitchen equipment is governed by NEC Table 120.56 , which applies tiered diversity factors based on the total number of appliances: 100% for 1–2 units , 90% for 3 units , 80% for 4 units , 70% for 5 units , and 65% for 6 or more units . Crucially, Section 120.56 establishes an unyielding statutory floor: in no case shall the calculated feeder demand be less than the sum of the two largest kitchen loads . For educational facilities equipped with electric heating or cooling, NEC 120.86 provides an optional method evaluating total connected load per square foot: 100% of the first 3 VA/ft 2 3\text{ VA/ft}^2 3 VA/ft 2 , 75% of the next 17 VA/ft 2 17\text{ VA/ft}^2 17 VA/ft 2 ( 3 to 20 VA/ft 2 3\text{ to } 20\text{ VA/ft}^2 3 to 20 VA/ft 2 ), and 25% of any remainder over 20 VA/ft 2 20\text{ VA/ft}^2 20 VA/ft 2 .

Certain commercial occupancy classes present concentrated, highly specialized electrical profiles. Commercial food service facilities (restaurants, institutional cafeterias, corporate dining rooms) feature heavy concentrations of high-kilowatt heating, cooking, and sanitation equipment. Conversely, academic buildings feature expansive physical footprints with variable occupancy schedules.

To prevent unnecessary oversizing, the NEC provides specialized demand schedules in the standard and optional feeder and service calculations of Article 120 (Article 120 in the 2023 and earlier editions).

Commercial Kitchen Equipment Sizing (NEC 120.56 & Table 120.56)

Under NEC Section 120.56 , the load for commercial electric cooking equipment, dishwasher booster heaters, and other kitchen equipment may be calculated with the demand factors of Table 120.56. Electricians must recognize that NEC Table 120.55 applies strictly to household cooking equipment ; commercial food service equipment can never be calculated using Table 120.55.

Table 120.56 Demand Factor Schedule

  • Number of Commercial Kitchen Units Demand Factor (Percent) Minimum Feeder Demand Floor Rule
  • 1 unit 100% ( 1.00 1.00 1.00 ) Must equal 100% of nameplate rating
  • 2 units 100% ( 1.00 1.00 1.00 ) Sum of both units ( 100 % 100\% 100% )
  • 3 units 90% ( 0.90 0.90 0.90 ) Not less than sum of largest two units
  • 4 units 80% ( 0.80 0.80 0.80 ) Not less than sum of largest two units
  • 5 units 70% ( 0.70 0.70 0.70 ) Not less than sum of largest two units
  • 6 or more units 65% ( 0.65 0.65 0.65 ) Not less than sum of largest two units
  • Qualifying Equipment Scope

Equipment that qualifies for the Table 120.56 demand factors includes commercially rated:

  • Electric deep-fat fryers
  • Commercial convection and deck ovens
  • Commercial griddles, broilers, and salamanders
  • Commercial dishwashers and hot-water booster heaters
  • Steam kettles, tilting skillets, and steam tables
  • Commercial food warmers and holding cabinets
  • Commercial electric ranges and cooktops
  • Explicit Exclusions Under NEC 120.56

Section 120.56 explicitly states that these demand factors do not apply to:

Electric space-heating equipment (calculated under Article 424).

Ventilation fans and make-up air systems (calculated under Article 430).

Air-conditioning and refrigeration equipment (calculated under Article 440).

The method is three steps: add the nameplate ratings of all qualifying kitchen equipment, multiply the total by the Table 120.56 factor for the number of units, and compare the result with the sum of the two largest units. The feeder demand is the greater of the two values.

The Critical 'Two Largest Units' Rule in Action

The statutory condition in NEC 120.56 states: "In no case shall the feeder demand be less than the sum of the largest two kitchen equipment loads."

This rule frequently appears on the Minnesota journeyworker examination because it exposes candidates who blindly apply percentage multipliers without reading code footnotes and limitations.

Scenario A: Standard Proportionate Kitchen (Table Percentage Governs)

A cafeteria installs 6 pieces of kitchen equipment:

  • Combi-oven: 14 kW 14\text{ kW} 14 kW
  • Conveyor dishwasher: 12 kW 12\text{ kW} 12 kW
  • Booster heater: 10 kW 10\text{ kW} 10 kW
  • Deep fryer: 10 kW 10\text{ kW} 10 kW
  • Griddle: 8 kW 8\text{ kW} 8 kW
  • Food warmer: 6 kW 6\text{ kW} 6 kW

Total Connected Load: 14 + 12 + 10 + 10 + 8 + 6 = 60 kW 14 + 12 + 10 + 10 + 8 + 6 = 60\text{ kW} 14 + 12 + 10 + 10 + 8 + 6 = 60 kW .

Apply Table 120.56 (6 units = 65%): 60 kW × 0.65 = 39 kW 60\text{ kW} \times 0.65 = \mathbf{39\text{ kW}} 60 kW × 0.65 = 39 kW .

Check Statutory Floor (Two Largest): Largest two are 14 kW + 12 kW = 26 kW 14\text{ kW} + 12\text{ kW} = \mathbf{26\text{ kW}} 14 kW + 12 kW = 26 kW .

Final Feeder Demand: Because 39 kW ≥ 26 kW 39\text{ kW} \ge 26\text{ kW} 39 kW ≥ 26 kW , the calculated demand is 39 kW \mathbf{39\text{ kW}} 39 kW ( 39,000 VA 39{,}000\text{ VA} 39 , 000 VA ).

Scenario B: Disproportionate Kitchen (Statutory Floor Governs)

A specialty bakery installs 4 pieces of commercial equipment:

  • Commercial deck baking oven: 30 kW 30\text{ kW} 30 kW
  • High-temp conveyor warewasher: 22 kW 22\text{ kW} 22 kW
  • Proofer cabinet: 3 kW 3\text{ kW} 3 kW
  • Countertop food warmer: 2 kW 2\text{ kW} 2 kW

Total Connected Load: 30 + 22 + 3 + 2 = 57 kW 30 + 22 + 3 + 2 = 57\text{ kW} 30 + 22 + 3 + 2 = 57 kW .

Apply Table 120.56 (4 units = 80%): 57 kW × 0.80 = 45.6 kW 57\text{ kW} \times 0.80 = \mathbf{45.6\text{ kW}} 57 kW × 0.80 = 45.6 kW .

Check Statutory Floor (Two Largest): Largest two are 30 kW + 22 kW = 52 kW 30\text{ kW} + 22\text{ kW} = \mathbf{52\text{ kW}} 30 kW + 22 kW = 52 kW .

Final Feeder Demand: Because 45.6 kW < 52 kW 45.6\text{ kW} < 52\text{ kW} 45.6 kW < 52 kW , the statutory floor overrides the percentage calculation! The minimum feeder demand is 52 kW \mathbf{52\text{ kW}} 52 kW ( 52,000 VA 52{,}000\text{ VA} 52 , 000 VA ).

Exam Warning: Sizing this feeder for 45.6 kW 45.6\text{ kW} 45.6 kW violates NEC 120.56 and will fail an electrical inspection.

Optional Calculation for Schools (NEC 120.86 & Table 120.86)

Under NEC Section 120.86 , an optional calculation method is permitted for determining the feeder or service load for a school.

Statutory Eligibility Prerequisites

To utilize Section 120.86, the school building must meet the following criteria:

Must be equipped with electric space heating, air conditioning, or both .

If the school has no electric space heating or air conditioning (for example, gas-fired hydronic heat with no electric cooling), the optional method cannot be used; use the standard calculation.

The connected load includes all interior and exterior lighting, power, water heating, cooking, other loads, and the larger of the air-conditioning or space-heating load.

Table 120.86 Demand Schedule

Demand factors are applied to the total connected load expressed in volt-amperes per square foot of interior floor area:

Connected Load Bracket (VA/sq ft) Demand Factor Net Calculated Demand Allowance

First 3 VA/ft 2 3\text{ VA/ft}^2 3 VA/ft 2 or less 100% ( 1.00 1.00 1.00 ) Area × 3 VA/ft 2 × 1.00 \text{Area} \times 3\text{ VA/ft}^2 \times 1.00 Area × 3 VA/ft 2 × 1.00

From 3 to 20 VA/ft 2 3\text{ to } 20\text{ VA/ft}^2 3 to 20 VA/ft 2 (Next 17 VA/ft 2 17\text{ VA/ft}^2 17 VA/ft 2 ) 75% ( 0.75 0.75 0.75 ) Area × 17 VA/ft 2 × 0.75 \text{Area} \times 17\text{ VA/ft}^2 \times 0.75 Area × 17 VA/ft 2 × 0.75

Remainder over 20 VA/ft 2 20\text{ VA/ft}^2 20 VA/ft 2 25% ( 0.25 0.25 0.25 ) Area × ( VA/ft 2 − 20 ) × 0.25 \text{Area} \times (\text{VA/ft}^2 - 20) \times 0.25 Area × ( VA/ft 2 − 20 ) × 0.25

Complete Worked School Calculation

Calculate the service load for a 50,000 sq ft 50{,}000\text{ sq ft} 50 , 000 sq ft high school with a total connected load of 1,400,000 VA 1{,}400{,}000\text{ VA} 1 , 400 , 000 VA ( 1,400 kVA 1{,}400\text{ kVA} 1 , 400 kVA ) supplied by a 480 Y / 277 V 480Y/277\text{ V} 480 Y /277 V , 3-phase, 4-wire system.

Step 1: Calculate Total Connected Load per Square Foot

Unit Connected Load = 1,400,000 VA 50,000 sq ft = 28 VA/ft 2 \text{Unit Connected Load} = \frac{1{,}400{,}000\text{ VA}}{50{,}000\text{ sq ft}} = 28\text{ VA/ft}^2 Unit Connected Load = 50 , 000 sq ft 1 , 400 , 000 VA ​ = 28 VA/ft 2

Step 2: Apply Table 120.86 Demand Tiers

Tier 1 (First 3 VA/ft 2 3\text{ VA/ft}^2 3 VA/ft 2 at 100%): 50,000 sq ft × 3 VA/ft 2 × 1.00 = 150,000 VA 50{,}000\text{ sq ft} \times 3\text{ VA/ft}^2 \times 1.00 = \mathbf{150{,}000\text{ VA}} 50 , 000 sq ft × 3 VA/ft 2 × 1.00 = 150 , 000 VA

Tier 2 ( 3 to 20 VA/ft 2 3\text{ to } 20\text{ VA/ft}^2 3 to 20 VA/ft 2 , representing 17 VA/ft 2 17\text{ VA/ft}^2 17 VA/ft 2 at 75%): 50,000 sq ft × 17 VA/ft 2 × 0.75 = 637,500 VA 50{,}000\text{ sq ft} \times 17\text{ VA/ft}^2 \times 0.75 = \mathbf{637{,}500\text{ VA}} 50 , 000 sq ft × 17 VA/ft 2 × 0.75 = 637 , 500 VA

Tier 3 (Remainder over 20 VA/ft 2 20\text{ VA/ft}^2 20 VA/ft 2 , which is 28 − 20 = 8 VA/ft 2 28 - 20 = 8\text{ VA/ft}^2 28 − 20 = 8 VA/ft 2 at 25%): 50,000 sq ft × 8 VA/ft 2 × 0.25 = 100,000 VA 50{,}000\text{ sq ft} \times 8\text{ VA/ft}^2 \times 0.25 = \mathbf{100{,}000\text{ VA}} 50 , 000 sq ft × 8 VA/ft 2 × 0.25 = 100 , 000 VA

Step 3: Sum the Tiers for Total Demand

Net Calculated Service Demand = 150,000 VA + 637,500 VA + 100,000 VA = 887,500 VA ( 887.5 kVA ) \text{Net Calculated Service Demand} = 150{,}000\text{ VA} + 637{,}500\text{ VA} + 100{,}000\text{ VA} = \mathbf{887{,}500\text{ VA}} \quad (887.5\text{ kVA}) Net Calculated Service Demand = 150 , 000 VA + 637 , 500 VA + 100 , 000 VA = 887 , 500 VA ( 887.5 kVA )

Step 4: Calculate 3-Phase Service Current at 480V

Service Amperes = 887,500 VA 3 × 480 V = 887,500 831.38 = 1,067.5 Amperes \text{Service Amperes} = \frac{887{,}500\text{ VA}}{\sqrt{3} \times 480\text{ V}} = \frac{887{,}500}{831.38} = \mathbf{1{,}067.5\text{ Amperes}} Service Amperes = 3 ​ × 480 V 887 , 500 VA ​ = 831.38 887 , 500 ​ = 1 , 067.5 Amperes

Sizing Service Equipment: A standard 1,200-Ampere , 480Y/277V switchboard is specified.

Optional Calculation for New Restaurants (NEC 120.88 & Table 120.88)

Under NEC Section 120.88 , an alternative optional calculation is available for new restaurant services or feeders where the total connected load is known. Table 120.88 distinguishes between all-electric restaurants and not all-electric restaurants (those utilizing gas cooking/heating with electric auxiliaries):

  • Connected Load Bracket All-Electric Demand Factor Not All-Electric Demand Factor
  • First 200 kVA 200\text{ kVA} 200 kVA or less 80% ( 0.80 0.80 0.80 ) 100% ( 1.00 1.00 1.00 )
  • 201 to 325 kVA 201\text{ to } 325\text{ kVA} 201 to 325 kVA 10% ( 0.10 0.10 0.10 ) 50% ( 0.50 0.50 0.50 )
  • 326 to 800 kVA 326\text{ to } 800\text{ kVA} 326 to 800 kVA 50% ( 0.50 0.50 0.50 ) 45% ( 0.45 0.45 0.45 )
  • Remainder over 800 kVA 800\text{ kVA} 800 kVA 50% ( 0.50 0.50 0.50 ) 20% ( 0.20 0.20 0.20 )

Because of the sharp drop in the second bracket for all-electric facilities ( 10 % 10\% 10% between 201 and 325 kVA 201\text{ and } 325\text{ kVA} 201 and 325 kVA ), Section 120.88 frequently produces substantial reductions in required service ampacity compared to standard Part III methods.

  • Practical Exam Scenarios & Trap Avoidance
  • Trap 1: Including Commercial Kitchen Exhaust Hood Fans in Table 120.56

Scenario: A question lists five kitchen cooking appliances totaling 45 kW 45\text{ kW} 45 kW plus a 5 HP 5\text{ HP} 5 HP exhaust hood blower motor ( 240 V 240\text{ V} 240 V , 28 A = 6,720 VA 28\text{ A} = 6{,}720\text{ VA} 28 A = 6 , 720 VA ) and asks for the Table 120.56 demand load.

Common Error: Lumping the exhaust fan motor into Table 120.56 as a 6th unit and multiplying 51.72 kW × 0.65 51.72\text{ kW} \times 0.65 51.72 kW × 0.65 .

Correct Code Application: Ventilation motors are explicitly excluded from Table 120.56. Calculate the 5 kitchen appliances at 70 % 70\% 70% under Table 120.56 ( 45 kW × 0.70 = 31.5 kW 45\text{ kW} \times 0.70 = 31.5\text{ kW} 45 kW × 0.70 = 31.5 kW ), and calculate the ventilation fan motor separately under NEC Article 430 at 125 % 125\% 125% .

Trap 2: Incorrect Square Footage Tiering in Table 120.86

Scenario: Calculating school demand by multiplying the entire connected load by 75 % 75\% 75% .

Correct Code Application: Table 120.86 is tiered identically to progressive tax brackets. The first 3 VA/ft 2 3\text{ VA/ft}^2 3 VA/ft 2 must be evaluated at 100 % 100\% 100% , the span between 3 and 20 VA/ft 2 3\text{ and } 20\text{ VA/ft}^2 3 and 20 VA/ft 2 ( 17 VA/ft 2 17\text{ VA/ft}^2 17 VA/ft 2 maximum) at 75 % 75\% 75% , and only the excess over 20 VA/ft 2 20\text{ VA/ft}^2 20 VA/ft 2 at 25 % 25\% 25% .