Study guide

7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

Key Takeaways Explain This Topic AI

Under the 2026 NEC 230.70(A)(1), the service disconnect for a one- or two-family dwelling must be readily accessible and outdoors, either on the dwelling or within sight and not more than 50 ft from it.

One- and two-family dwelling service disconnects must be marked EMERGENCY DISCONNECT in white letters at least ½ in. high on a red background, permanently affixed and not handwritten.

Each service may have one disconnecting means, or two to six disconnects grouped at one location under the conditions of 230.71 and 230.72.

The service disconnect for a one-family dwelling must be rated at least 100 A, 3-wire (230.79(C)), and for other installations generally at least 60 A (230.79(D)).

GFPE is required for each service disconnect rated 1000 A or more on a solidly grounded wye system over 150 V to ground, such as 480Y/277 V, with a maximum setting of 1200 A (230.95).

Last updated: October 2026

What changed for 2026

DLI's 2026 NEC adoption review highlighted Article 230 changes that directly affect Minnesota service work:

230.70(A)(1): for one- and two-family dwellings, the service disconnecting means must be readily accessible and located outdoors , either on the dwelling or within sight of it (110.29: visible and not more than 50 ft away).

230.85 deleted: the separate 2023 "emergency disconnect" rule was folded into 230.70. The outdoor service disconnect is the emergency disconnect.

Markings: service disconnects are marked SERVICE DISCONNECT (other than one- and two-family dwellings) or EMERGENCY DISCONNECT (one- and two-family dwellings), and other energy-source disconnects not located at the service must be listed on a plaque or directory at the service disconnect.

230.70(F): a remote-control device, such as a pushbutton for a shunt-trip breaker, is not a service disconnecting means.

230.46: an Informational Note recognizes the marking "SVC" as equivalent to "suitable for use on the line side of the service equipment" for splicing and tap devices.

Location of the service disconnect (230.70(A))

  • Occupancy Location
  • One- and two-family dwellings Readily accessible, outdoors , on the dwelling or within sight of it

All other buildings A readily accessible location either outside the building or inside nearest the point of entrance of the service conductors

Any building Not in bathrooms

Each service disconnect must be permanently marked to identify it as a service disconnect, and the marking must meet 110.21(B): durable for the environment, not handwritten, and permanently affixed.

Marking details

  • Building type Marking
  • Other than one- and two-family dwellings SERVICE DISCONNECT , on or adjacent to the disconnect

One- and two-family dwellings EMERGENCY DISCONNECT , on the outside front of the enclosure, white letters at least ½ in. high on a red background

Other energy sources (PV, generators, ESS) not adjacent to the service disconnect A plaque or directory at the service disconnect identifying the location of each source disconnect

Number and grouping of disconnects (230.71 and 230.72)

Each service may have one disconnecting means, or two to six disconnecting means where each is in a separate enclosure, or in switchgear, switchboards, or panelboards with barriers as permitted by 230.71(B). Multiple disconnects must be grouped at one location and each marked to show the load it serves. Disconnects for fire pumps, emergency systems, legally required or optional standby systems, and parallel power production systems must be installed remote from the normal service disconnects, so first responders do not open them by accident.

Number of service-entrance conductor sets (230.40)

Each service drop, set of overhead service conductors, set of underground service conductors, or service lateral may supply only one set of service-entrance conductors . The exceptions cover common layouts:

A building with more than one occupancy may have one set of service-entrance conductors run to each occupancy or group of occupancies.

Where separate disconnect enclosures are grouped at one location and supply separate loads from one service drop or lateral, one set of service-entrance conductors may supply each or several of the enclosures.

A one-family dwelling and its accessory structures may each have one set of service-entrance conductors from a single service drop or lateral.

Two-family and multifamily dwellings and multiple-occupancy buildings may have one set to supply the common house loads covered in 210.25.

One set connected ahead of the normal service disconnect may supply the systems that 230.82 allows on the supply side, such as fire pump equipment or a power production source.

Rating and type (230.76 to 230.80)

Rule Requirement

Operation (230.76) Manually operable switch or circuit breaker, or a power-operated switch or breaker that can also be opened by hand

Indicating (230.77) Plainly indicates whether it is open or closed

Rating (230.79) One-circuit installations at least 15 A ; two-circuit installations at least 30 A ; one-family dwellings at least 100 A, 3-wire ; all others at least 60 A

Combined rating (230.80) Where there are multiple disconnects, their combined rating may not be less than the rating required for a single disconnect

The ampacity of the ungrounded service-entrance conductors may not be less than the minimum disconnect rating in 230.79 (230.42(B)).

Service equipment and meter sockets

230.66: service equipment must be listed (or field evaluated) and marked suitable for use as service equipment .

Meter sockets are not service equipment, but they must be listed and rated for the voltage and current rating of the service. A 2026 exception (230.68) lets a fire pump meter socket be sized to the circuit rating rather than the fire pump service current.

230.62(C) barriers: service equipment must have barriers so that no uninsulated, ungrounded service busbar or terminal is exposed to inadvertent contact while servicing load terminations.

230.82: only listed items may be connected on the supply side of the service disconnect, such as meters and meter sockets, meter disconnect switches rated for the available fault current, instrument transformers, surge arresters and Type 1 SPDs, and conductors for emergency, standby, fire pump, and power production sources when they have their own disconnecting means and overcurrent protection. The 2026 NEC reorganized this list.

Surge protection (230.67)

All services supplying dwelling units must have a surge-protective device (SPD) , Type 1 or Type 2, that is an integral part of the service equipment or located immediately adjacent to it (or, where permitted, at the next level of distribution). The 2023 edition extended this to dormitory units, guest rooms and guest suites of hotels and motels, and areas of nursing homes and limited-care facilities. When service equipment is replaced , an SPD must be installed. The 2026 NEC also requires an SPD where existing service equipment is reconnected to a replacement mobile or manufactured home (550.51).

Overcurrent protection (230.90 and 230.91)

Each ungrounded service conductor must have overload protection by an OCPD in series, with a rating not higher than the conductor ampacity, except as permitted by 240.4(B) and for up to six circuit breakers or sets of fuses whose combined ratings may exceed the conductor ampacity. The service OCPD must be an integral part of the service disconnecting means or located immediately adjacent to it (230.91).

Ground-fault protection of equipment (230.95)

GFPE is required for solidly grounded wye services of more than 150 V to ground (such as 480Y/277 V ) for each service disconnect rated 1000 A or more :

  • maximum ground-fault setting 1200 A ;
  • maximum time delay 1 second for ground-fault currents of 3000 A or more ;

the system must be performance tested when first installed, following the manufacturer's instructions, and a written record kept for the AHJ.

GFPE is not required for a continuous industrial process where a nonorderly shutdown would create additional hazards, and it is not permitted on fire pump services. A 208Y/120 V service never requires GFPE under 230.95, because it is only 120 V to ground.

Worked example: a new Minnesota home

A new single-family house gets a 200 A, 120/240 V underground service with rooftop PV.

Install a meter-main (combination meter socket and main breaker) on the outside wall. The main breaker is the outdoor, readily accessible service disconnect required by 230.70(A)(1).

Mark it EMERGENCY DISCONNECT with white letters at least ½ in. high on a red background.

The 200 A rating exceeds the 100 A minimum of 230.79(C).

Provide a Type 1 or Type 2 SPD at the service equipment (230.67).

The PV system disconnect is on the garage wall, not next to the meter-main, so install a plaque or directory at the service disconnect showing where the PV disconnect is.