Study guide
9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66)
Minnesota Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Minnesota Exam, Licensing & Electrical Law
1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement
2 Electrical Theory, Math & Power Calculations
2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting
3 NEC Structure & General Requirements
3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)
4 Conductors, Identification & Ampacity
4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors
5 Branch Circuits, GFCI/AFCI & Required Outlets
5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)
6 Load Calculations (2026 NEC Article 120)
6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)
7 Feeders, Outside Wiring & Services
7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)
8 Overcurrent Protection
8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction
9 System Grounding & Grounding Electrodes
9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems
10 Bonding & Equipment Grounding
10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding
11 General Wiring Methods & Underground Installations
11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)
12 Raceways, Cables & Conduit Fill
12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)
13 Boxes, Conduit Bodies & Cabinets
13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)
14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances
14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)
15 Motors, Controllers & Air Conditioning
15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)
16 Transformers, Generators & Equipment Over 1000 Volts
16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)
17 Hazardous (Classified) Locations
17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)
18 Health Care, Assembly, Agricultural & Mobile Occupancies
18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)
19 Signs, Elevators, Pools, Solar & Other Specific Equipment
19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)
20 Emergency, Standby & Interconnected Power Sources
20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)
21 Limited-Energy, Fire Alarm & Communications Systems
21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)
9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66)
Key Takeaways Explain This Topic AI
Grounding Electrode Conductors (GECs) for alternating-current systems are sized using NEC Table 250.66 based on the circular mil area of the largest ungrounded service-entrance conductor (or equivalent parallel area), NOT on the service overcurrent rating.
Under NEC 250.66(A), where the GEC connects to a rod, pipe, or plate electrode as its sole connection, that portion of the conductor is never required to be larger than 6 AWG copper or 4 AWG aluminum.
Under NEC 250.66(B), where the GEC connects to a concrete-encased electrode as its sole connection, that portion is never required to be larger than 4 AWG copper.
Under NEC 250.66(C), where the GEC connects to a ground ring as its sole connection, that portion is never required to be larger than the conductor used for the ground ring (minimum 2 AWG copper).
NEC 250.64(E) mandates that ferrous metal raceways housing a GEC must be electrically bonded at both ends to the enclosure and the conductor to eliminate high inductive reactance (the choke effect) during lightning or transient surge events.
Last updated: October 2026
9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66)
Quick Answer: The Grounding Electrode Conductor (GEC) is sized according to NEC Table 250.66 based on the cross-sectional area of the largest ungrounded service-entrance conductor (or the sum of parallel conductors), never on the rating of the service overcurrent protective device. Crucially, sole-connection exceptions cap the maximum required GEC size regardless of service ampacity: maximum 6 AWG copper for driven rods/pipes (NEC 250.66(A)), maximum 4 AWG copper for concrete-encased electrodes (NEC 250.66(B)), and maximum 2 AWG copper (or ring size) for ground rings (NEC 250.66(C)).
The Grounding Electrode Conductor (GEC) is the heavy-gauge wire that connects the system grounded conductor (neutral) or service equipment enclosure directly to the grounding electrode system. Sizing the GEC correctly is one of the most critical calculation skills tested on the Minnesota Journeyworker examination. Candidates must navigate Table 250.66 with precision, combine circular mil areas for parallel services, and apply the sole-connection exceptions without over-sizing conductors unnecessarily.
NEC Table 250.66: Sizing Rules & Complete Reference
Unlike Equipment Grounding Conductors (which are sized per Table 250.122 based on circuit breaker ratings), Grounding Electrode Conductors are sized strictly by the size of the incoming ungrounded service conductors .
Size of Largest Ungrounded Service-Entrance Conductor or Equivalent Area for Parallel Conductors (Copper) Size of Largest Ungrounded Service-Entrance Conductor or Equivalent Area for Parallel Conductors (Aluminum / Copper-Clad Aluminum) Minimum Size Grounding Electrode Conductor (Copper) Minimum Size Grounding Electrode Conductor (Aluminum / Copper-Clad Aluminum)
- 2 AWG or smaller 1/0 AWG or smaller 8 AWG 6 AWG
- 1 AWG or 1/0 AWG 2/0 AWG or 3/0 AWG 6 AWG 4 AWG
- 2/0 AWG or 3/0 AWG 4/0 AWG or 250 kcmil 4 AWG 2 AWG
- Over 3/0 AWG through 350 kcmil Over 250 kcmil through 500 kcmil 2 AWG 1/0 AWG
- Over 350 kcmil through 600 kcmil Over 500 kcmil through 900 kcmil 1/0 AWG 3/0 AWG
- Over 600 kcmil through 1100 kcmil Over 900 kcmil through 1750 kcmil 2/0 AWG 4/0 AWG
- Over 1100 kcmil Over 1750 kcmil 3/0 AWG 250 kcmil
Exam Trap Alert: Notice that the largest GEC required by Table 250.66 for copper is 3/0 AWG , even for a massive 4,000-ampere service with tens of thousands of circular mils. The table tops out at 3/0 AWG copper (250 kcmil aluminum).
- Sizing Calculations: Single vs. Parallel Conductors
- Single Service-Entrance Conductor Calculation
Problem: A 200-ampere single-family residential service is supplied by 2/0 AWG copper THHN ungrounded service-entrance conductors. What is the minimum size copper GEC required to connect to an underground metal water pipe electrode?
Step 1: Identify the ungrounded service wire: 2/0 AWG copper.
Step 2: Locate 2/0 AWG in Column 1 of Table 250.66 ("2/0 or 3/0 AWG").
Step 3: Read the copper GEC size in Column 3: 4 AWG copper .
Parallel Service Conductor Calculation (Cross-Sectional Summation)
Where service-entrance conductors are installed in parallel sets (in two or more separate raceways or cables) under the parallel conductor rules of Article 310 (310.10(G) in the 2023 NEC), the size of the GEC is determined by calculating the equivalent total circular mil area of the largest ungrounded phase conductor per NEC Table 250.66 Note 1 .
Problem: A 400-ampere commercial service consists of two parallel raceways, each containing 250 kcmil copper THHN ungrounded conductors per phase. What is the minimum copper GEC required to connect to a metal underground water pipe electrode?
Step 1: Calculate the total equivalent cross-sectional area per phase: Total Area = 250 kcmil + 250 kcmil = 500 kcmil \text{Total Area} = 250\text{ kcmil} + 250\text{ kcmil} = 500\text{ kcmil} Total Area = 250 kcmil + 250 kcmil = 500 kcmil
Step 2: Find 500 kcmil in Table 250.66: Row "Over 350 kcmil through 600 kcmil".
Step 3: Read the required copper GEC in Column 3: 1/0 AWG copper .
The Sole-Connection Exceptions: NEC 250.66(A), (B), and (C)
The general sizing rules of Table 250.66 apply primarily to underground metal water pipes and structural building steel. For other specific electrodes, the NEC provides maximum size limitations (caps) under subsections 250.66(A), 250.66(B), and 250.66(C). These exceptions represent high-frequency questions on the Minnesota licensing exam.
1. Rod, Pipe, or Plate Electrodes (NEC 250.66(A))
"Where the grounding electrode conductor is connected to one or more of the electrodes specified in 250.52(A)(5) or (A)(7), that portion of the conductor that is the sole connection to the grounding electrode(s) shall not be required to be larger than 6 AWG copper wire or 4 AWG aluminum wire."
Physical Rationale: An 8-foot driven rod has high contact resistance with earth (25 ohms or more). Physics dictates that a ground rod simply cannot dissipate more surge current into soil than a 6 AWG copper conductor can safely conduct without overheating. Installing a 2/0 or 3/0 AWG conductor to a driven ground rod accomplishes nothing and wastes expensive copper.
Application: Even on a massive 4,000-ampere service with four parallel 500 kcmil conductors per phase ( 2,000 kcmil 2{,}000\text{ kcmil} 2 , 000 kcmil total), the conductor run solely to a driven ground rod is never required to be larger than 6 AWG copper .
2. Concrete-Encased Electrodes (NEC 250.66(B))
"Where the grounding electrode conductor is connected to a concrete-encased electrode as specified in 250.52(A)(3), that portion of the conductor that is the sole connection to the grounding electrode shall not be required to be larger than 4 AWG copper wire ."
Regardless of whether the service is 200 A, 800 A, or 2,500 A, a GEC run solely to a concrete-encased Ufer electrode is never required to exceed 4 AWG copper .
3. Ground Rings (NEC 250.66(C))
"Where the grounding electrode conductor is connected to a ground ring as specified in 250.52(A)(4), that portion of the conductor that is the sole connection to the grounding electrode shall not be required to be larger than the conductor used for the ground ring."
Because the minimum permitted size for a ground ring conductor under 250.52(A)(4) is 2 AWG bare copper, the maximum GEC run solely to a ground ring is typically 2 AWG copper .
Common GEC vs. Taps vs. Sole Connections
On installations with multiple electrodes, confusion often arises regarding how to apply Table 250.66 versus the sole-connection exceptions:
The Common Main GEC: If a single GEC runs from the service equipment to an underground water pipe (which requires a 1/0 AWG copper GEC based on service size), and then extends to a driven ground rod, the portion of the conductor between the service and the water pipe must be sized per Table 250.66 (1/0 AWG) .
Bonding Jumpers Between Electrodes (250.53(C) and 250.66): Bonding jumpers that interconnect electrodes are sized from 250.66, and the sole-connection limits still apply: a jumper that is the only connection to a rod need not exceed 6 AWG copper , one to a concrete-encased electrode need not exceed 4 AWG copper , and one to a ground ring need not exceed the ring conductor size.
Multiple Service Disconnects (250.64(D)): Where a service has more than one disconnect in separate enclosures, a common GEC with taps, individual GECs, or a common location busbar may be used, each sized from 250.66.
GEC Installation, Routing & Protection Rules (NEC 250.64)
NEC Section 250.64 establishes strict installation guidelines to ensure that grounding electrode conductors remain mechanically intact and electrically operational throughout the life of the building.
1. Continuous Conductor Requirement (NEC 250.64(C))
The GEC must be installed in one continuous length without a splice or joint, except under the following permitted conditions:
Splicing with irreversible compression connectors listed as grounding and bonding equipment, or by the exothermic welding process . The 2026 NEC also permits splices made with other listed grounding and bonding equipment where the splice is accessible.
Sections of busbar connected together to form a GEC.
Bolted, riveted, or welded connections of structural metal frames , and threaded, welded, brazed, soldered, or bolted-flange connections of metal water piping .
Where several GECs or bonding jumpers are connected at a busbar (250.64(F)(3)), the busbar must be at least 1 / 4 in. × 2 in. 1/4\text{ in.} \times 2\text{ in.} 1/4 in. × 2 in. copper or aluminum and securely fastened in an accessible location.
2. Physical Protection of GEC (NEC 250.64(B))
Smaller than 6 AWG (such as 8 AWG): Must always be protected in RMC, IMC, PVC, RTRC-XW, EMT, or cable armor.
6 AWG and Larger, Not Exposed to Physical Damage: May be run along the surface of the building without protection where securely fastened.
6 AWG and Larger, Exposed to Physical Damage: Must be protected in RMC, IMC, Schedule 80 PVC, RTRC-XW, EMT, or cable armor. There is no separate "severe damage" threshold for larger GECs.
3. Aluminum Conductor Restrictions (NEC 250.64(A))
Bare or covered aluminum or copper-clad aluminum GECs are strictly prohibited from being placed in direct contact with masonry, soil, or earth. Furthermore, where used outdoors, aluminum terminations must not be made within 18 inches (450 mm) of the earth.
The Ferrous Metal Raceway "Choke Effect" (NEC 250.64(E))
The 2026 NEC applies this rule to ferrous cable armor as well as raceways, and a new 250.64(G) prohibits routing a GEC through an enclosure's mounting or drainage openings .
A critical technical question frequently asked on journeyman exams addresses the electromagnetic consequences of enclosing a GEC in a steel conduit.
The Physics of Inductive Reactance
When lightning strikes or an intense utility surge occurs, the transient surge current has an extremely high frequency (equivalent to kilohertz or megahertz). If a GEC carrying this high-frequency current is enclosed within a ferrous metal raceway (such as steel RMC, IMC, or EMT):
The magnetic flux generated by the current inside the conductor concentrates in the surrounding steel wall of the conduit.
The steel pipe acts as the core of an inductor (choke coil), generating an immense counter-electromotive force (CEMF) and inductive reactance ( X L = 2 π f L X_L = 2\pi f L X L = 2 π f L ).
This inductive choke drastically restricts current flow, creating thousands of volts of drop across the raceway. The surge is prevented from reaching the earth, causing destructive flashovers and arcing inside the building.
The Code Mandate (NEC 250.64(E))
To neutralize the choke effect, NEC 250.64(E) mandates that:
"Ferrous metal enclosures and raceways for grounding electrode conductors shall be electrically continuous from the point of attachment to cabinets or equipment to the grounding electrode and shall be bonded at each end of the raceway or enclosure to the grounding electrode conductor."
Bonding both ends of the steel raceway with bonding bushings and jumpers puts the steel conduit in parallel with the copper wire. The conduit and copper wire now carry current in the same direction, canceling the internal magnetic field and completely eliminating inductive choking.