Study guide

10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B))

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B))

Key Takeaways Explain This Topic AI

Under NEC 250.122(B), where ungrounded conductors are increased in size from the minimum size that has sufficient ampacity for the intended load, wire-type equipment grounding conductors, where installed, must be increased in size proportionally according to circular mil area.

The proportional upsizing formula requires multiplying the circular mil area of the standard Table 250.122 EGC by the ratio of the circular mil area of the upsized phase conductor to the minimum phase conductor required for the load.

Conductor circular mil values for mathematical ratios must be taken from NEC Chapter 9, Table 8 (Conductor Properties); the calculated circular mil value must be matched to the next standard wire size equal to or larger.

The life-safety physics behind NEC 250.122(B) centers on ground-fault loop impedance: if ungrounded conductors are enlarged for long distances but the EGC remains small, high return path impedance will restrict fault current and prevent instantaneous magnetic circuit breaker tripping.

Proportional upsizing applies to wire-type EGCs whenever ungrounded conductors are enlarged from minimum ampacity size, but does not require upsizing of listed metallic raceways (such as EMT, IMC, or RMC) that serve as the sole equipment grounding conductor under NEC 250.118.

Last updated: October 2026

10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B))

Quick Answer: Under NEC Section 250.122(B) , whenever ungrounded (phase) conductors are increased in size from the minimum size required for the load (most commonly to overcome voltage drop over long circuit runs), any wire-type equipment grounding conductor (EGC) installed in the raceway or cable must be increased proportionally in circular mil area . The calculation requires finding the ratio of the upsized phase conductor circular mils to the original minimum phase conductor circular mils (using NEC Chapter 9, Table 8 ), multiplying that ratio by the minimum Table 250.122 EGC circular mils, and selecting the next larger standard conductor size.

Few provisions in the National Electrical Code trigger more unexpected failures on master and journeyman licensing exams than NEC Section 250.122(B) . Electricians often understand the necessity of upsizing ungrounded phase conductors to keep voltage drop below the 3% branch-circuit value suggested in the Informational Notes to 210.19. However, many fail to realize that increasing the size of the phase conductor without proportionally increasing the equipment grounding conductor compromises the entire ground-fault safety system.

The Electrical Physics Behind NEC 250.122(B)

Why does the code enforce this strict proportional upsizing requirement? The answer lies in the fundamental physics of total ground-fault loop impedance ( Z loop Z_{\text{loop}} Z loop ​ ) and the operating characteristics of inverse-time circuit breakers .

Inverse-Time Breaker Trip Curves

A standard molded-case circuit breaker possesses two distinct trip mechanisms:

Thermal Element (Bimetallic Strip): Responds to sustained overloads. It takes minutes to hours to trip at 125% to 200% of rated current.

Magnetic Element (Electromagnetic Coil): Responds to high-magnitude short circuits and ground faults. To achieve instantaneous tripping (within 1/2 to 1 cycle, or roughly 8 to 16 milliseconds), the fault current must reach 5 to 10 times the breaker rating .

The Long-Distance Impedance Hazard

Consider a 30-ampere, 120-volt branch circuit supplying an exterior parking lot sign located 300 feet from the electrical panel:

A standard 30A circuit breaker requires a magnetic inrush current of at least 150 to 300 amperes ( 5 × 5\times 5 × to 10 × 10\times 10 × ) to open instantaneously.

Conductor resistance is inversely proportional to cross-sectional area: R = ρ L A R = \frac{\rho L}{A} R = A ρ L ​ .

To combat voltage drop over the 300-foot run, the installer upsizes the phase conductors from 10 AWG to 4 AWG copper.

If the installer leaves the equipment grounding conductor at the standard Table 250.122 size of 10 AWG copper (which has an alternating-current resistance of roughly 1.2 Ω 1.2\ \Omega 1.2 Ω per 1000 feet per Chapter 9 Table 9):

Total round-trip fault loop resistance ( 300 ft 300\text{ ft} 300 ft of 4 AWG + 300 ft 300\text{ ft} 300 ft of 10 AWG) exceeds 0.45 ohms .

An arcing ground fault at the sign delivers a maximum fault current of: I fault = 120 V 0.45 Ω ≈ 266 A I_{\text{fault}} = \frac{120\text{ V}}{0.45\ \Omega} \approx 266\text{ A} I fault ​ = 0.45 Ω 120 V ​ ≈ 266 A

If the arcing fault exhibits impedance or contact resistance, actual current drops to 100 to 140 amperes .

At 120 amperes, the 30-ampere breaker fails to trip magnetically . It falls into its slow thermal trip curve, requiring between 5 and 20 seconds to trip.

During those 20 seconds, thousands of joules of explosive arcing energy melt the sign framing, ignite combustible building materials, and hold the exterior metal sign at a lethal touch-potential of 80 to 100 volts to ground.

By upsizing the EGC proportionally to 4 AWG copper, the return path impedance is slashed, ensuring that available fault current comfortably exceeds 600 amperes, forcing the breaker into its instantaneous magnetic trip region within milliseconds.

The NEC 250.122(B) Code Mandate

NEC Section 250.122(B) establishes the governing rule:

"Where ungrounded conductors are increased in size from the minimum size that has sufficient ampacity for the intended load, wire-type equipment grounding conductors, where installed, shall be increased in size proportionally according to the circular mil area of the ungrounded conductors."

The Proportional Sizing Formula

To determine the required minimum circular mil area of the upsized equipment grounding conductor, apply the circular mil ratio formula:

cmil EGC-new cmil EGC-min = cmil Phase-new cmil Phase-min \frac{\text{cmil}_{\text{EGC-new}}}{\text{cmil}_{\text{EGC-min}}} = \frac{\text{cmil}_{\text{Phase-new}}}{\text{cmil}_{\text{Phase-min}}} cmil EGC-min ​ cmil EGC-new ​ ​ = cmil Phase-min ​ cmil Phase-new ​ ​

Rearranging to solve for the new equipment grounding conductor:

cmil EGC-new = cmil EGC-min × ( cmil Phase-new cmil Phase-min ) \text{cmil}_{\text{EGC-new}} = \text{cmil}_{\text{EGC-min}} \times \left( \frac{\text{cmil}_{\text{Phase-new}}}{\text{cmil}_{\text{Phase-min}}} \right) cmil EGC-new ​ = cmil EGC-min ​ × ( cmil Phase-min ​ cmil Phase-new ​ ​ )

Where:

cmil Phase-min \text{cmil}_{\text{Phase-min}} cmil Phase-min ​ = Circular mil area of the minimum ungrounded conductor required for the load or overcurrent protective device rating (from NEC Chapter 9, Table 8).

cmil Phase-new \text{cmil}_{\text{Phase-new}} cmil Phase-new ​ = Circular mil area of the actual enlarged ungrounded conductor installed in the raceway (from NEC Chapter 9, Table 8).

cmil EGC-min \text{cmil}_{\text{EGC-min}} cmil EGC-min ​ = Circular mil area of the standard equipment grounding conductor required by NEC Table 250.122 for the overcurrent device.

cmil EGC-new \text{cmil}_{\text{EGC-new}} cmil EGC-new ​ = Minimum calculated circular mil area required for the upsized equipment grounding conductor.

NEC Chapter 9, Table 8: Conductor Properties Reference

All circular mil values used in official exam calculations must be taken directly from NEC Chapter 9, Table 8 (Conductor Properties):

Conductor Size (AWG or kcmil) Circular Mil Area (cmil) Solid Copper Resistance ( Ω / 1000 ft \Omega / 1000\text{ ft} Ω/1000 ft , Table 8 lists solid only through 8 AWG) Stranded Copper Resistance ( Ω / 1000 ft \Omega / 1000\text{ ft} Ω/1000 ft )

  • 14 AWG 4,110 3.07 3.14
  • 12 AWG 6,530 1.93 1.98
  • 10 AWG 10,380 1.21 1.24
  • 8 AWG 16,510 0.764 0.778
  • 6 AWG 26,240 — 0.491
  • 4 AWG 41,740 — 0.308
  • 3 AWG 52,620 — 0.245
  • 2 AWG 66,360 — 0.194
  • 1 AWG 83,690 — 0.154
  • 1/0 AWG 105,600 — 0.122
  • 2/0 AWG 133,100 — 0.0967
  • 3/0 AWG 167,800 — 0.0766
  • 4/0 AWG 211,600 — 0.0608
  • 250 kcmil 250,000 — 0.0515
  • 300 kcmil 300,000 — 0.0429
  • 350 kcmil 350,000 0.0359 0.0367
  • 400 kcmil 400,000 0.0314 0.0321
  • 500 kcmil 500,000 0.0251 0.0258
  • Step-by-Step Worked Calculations
  • Worked Example 1: 30-Ampere Branch Circuit Upsized for Voltage Drop

Problem: A 240-volt single-phase branch circuit is protected by a 30-ampere circuit breaker. The circuit supplies an exterior gate motor 275 feet away. The minimum conductor required for ampacity is 10 AWG copper. To prevent excessive voltage drop during motor starting, the ungrounded phase conductors are increased in size to 4 AWG copper. What is the minimum size copper equipment grounding conductor required by NEC 250.122(B)?

Step 1: Identify minimum phase conductor and its circular mil area.

Minimum phase conductor for 30A circuit = 10 AWG copper.

From Chapter 9, Table 8: 10 AWG = 10,380 cmil .

Step 2: Identify upsized phase conductor circular mil area.

Installed phase conductor = 4 AWG copper.

From Chapter 9, Table 8: 4 AWG = 41,740 cmil .

Step 3: Calculate the area enlargement multiplier. Multiplier = 41 , 740 cmil 10 , 380 cmil = 4.0212 \text{Multiplier} = \frac{41,740\text{ cmil}}{10,380\text{ cmil}} = 4.0212 Multiplier = 10 , 380 cmil 41 , 740 cmil ​ = 4.0212

Step 4: Identify the minimum Table 250.122 EGC size and circular mil area.

From NEC Table 250.122, the minimum copper EGC for a 30-ampere overcurrent device is 10 AWG copper.

From Chapter 9, Table 8: 10 AWG = 10,380 cmil .

Step 5: Calculate the required new EGC circular mil area. cmil EGC-new = 10 , 380 cmil × 4.0212 = 41 , 740 cmil \text{cmil}_{\text{EGC-new}} = 10,380\text{ cmil} \times 4.0212 = 41,740\text{ cmil} cmil EGC-new ​ = 10 , 380 cmil × 4.0212 = 41 , 740 cmil

Step 6: Select the new conductor size from Chapter 9, Table 8.

Referring to Table 8, a 4 AWG conductor has exactly 41,740 cmil .

Final Answer: The equipment grounding conductor must be upsized to 4 AWG copper .

Worked Example 2: 100-Ampere Feeder Upsized for Voltage Drop

Problem: A 100-ampere subpanel is fed from a main distribution board located 350 feet away in an adjacent warehouse wing. The circuit is protected by a 100-ampere circuit breaker with 75°C terminals. The minimum conductor required for ampacity is 3 AWG copper. To limit voltage drop to 2%, the ungrounded phase conductors are upsized to 1/0 AWG copper. What is the minimum size copper equipment grounding conductor required?

Step 1: Identify minimum phase conductor and its circular mil area.

Minimum phase conductor for 100A at 75°C = 3 AWG copper (NEC Table 310.16 rating: 100A).

From Chapter 9, Table 8: 3 AWG = 52,620 cmil .

Step 2: Identify upsized phase conductor circular mil area.

Installed phase conductor = 1/0 AWG copper.

From Chapter 9, Table 8: 1/0 AWG = 105,600 cmil .

Step 3: Calculate the area enlargement multiplier. Multiplier = 105 , 600 cmil 52 , 620 cmil = 2.00684 \text{Multiplier} = \frac{105,600\text{ cmil}}{52,620\text{ cmil}} = 2.00684 Multiplier = 52 , 620 cmil 105 , 600 cmil ​ = 2.00684

Step 4: Identify the minimum Table 250.122 EGC size and circular mil area.

From NEC Table 250.122, the minimum copper EGC for a 100-ampere overcurrent device is 8 AWG copper .

From Chapter 9, Table 8: 8 AWG = 16,510 cmil .

Step 5: Calculate the required new EGC circular mil area. cmil EGC-new = 16 , 510 cmil × 2.00684 = 33 , 133 cmil \text{cmil}_{\text{EGC-new}} = 16,510\text{ cmil} \times 2.00684 = 33,133\text{ cmil} cmil EGC-new ​ = 16 , 510 cmil × 2.00684 = 33 , 133 cmil

Step 6: Select the new conductor size from Chapter 9, Table 8.

Looking at Chapter 9, Table 8:

  • 6 AWG = 26,240 cmil (less than 33,133 cmil, INSUFFICIENT)
  • 4 AWG = 41,740 cmil (exceeds 33,133 cmil, COMPLIANT)

Final Answer: The equipment grounding conductor must be upsized to 4 AWG copper .

Worked Example 3: 200-Ampere Feeder Upsized for Voltage Drop

Problem: A 200-ampere, 480Y/277V, 3-phase feeder runs 500 feet to an outbuilding. The minimum ungrounded conductor required for ampacity is 3/0 AWG copper (rated 200A at 75°C). The designer upsizes the phase conductors to 350 kcmil copper to combat voltage drop. What is the minimum required size of the copper equipment grounding conductor?

Step 1: Identify minimum phase conductor cmil.

3/0 AWG copper = 167,800 cmil .

Step 2: Identify upsized phase conductor cmil.

350 kcmil copper = 350,000 cmil .

Step 3: Calculate the multiplier. Multiplier = 350 , 000 cmil 167 , 800 cmil = 2.0858 \text{Multiplier} = \frac{350,000\text{ cmil}}{167,800\text{ cmil}} = 2.0858 Multiplier = 167 , 800 cmil 350 , 000 cmil ​ = 2.0858

Step 4: Identify minimum Table 250.122 EGC.

For a 200A overcurrent device, Table 250.122 specifies 6 AWG copper .

6 AWG copper = 26,240 cmil .

Step 5: Calculate required EGC cmil. cmil EGC-new = 26 , 240 cmil × 2.0858 = 54 , 731 cmil \text{cmil}_{\text{EGC-new}} = 26,240\text{ cmil} \times 2.0858 = 54,731\text{ cmil} cmil EGC-new ​ = 26 , 240 cmil × 2.0858 = 54 , 731 cmil

Step 6: Select conductor size from Chapter 9, Table 8.

Evaluating standard sizes:

  • 3 AWG = 52,620 cmil (less than 54,731 cmil, INSUFFICIENT)
  • 2 AWG = 66,360 cmil (exceeds 54,731 cmil, COMPLIANT)

Final Answer: The equipment grounding conductor must be upsized to 2 AWG copper .

Critical Examination Pitfalls & Exceptions