Study guide

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways

Key Takeaways Explain This Topic AI

Electrical Metallic Tubing (EMT) must be securely fastened within 3 feet of each box, cabinet, or fitting, and supported at intervals not exceeding 10 feet under NEC 358.30.

Rigid Metal Conduit (RMC) supports are required within 3 feet of terminations and every 10 feet, but straight runs with threaded couplings can extend support spacing up to 20 feet for trade size 2 and larger per Table 344.30(B)(2).

Schedule 80 PVC is explicitly mandated by NEC 352.10(F) where exposed raceways are subject to physical damage, whereas Schedule 40 PVC is strictly prohibited in such locations under NEC 352.12(C).

The total degrees of bends in a single raceway run between pull points, junction boxes, or terminations must not exceed 360 degrees (four quarter bends) across all metal and nonmetallic raceway articles.

Nonmetallic raceways such as PVC (Article 352) and RTRC (Article 355) do not serve as equipment grounding conductors and always require an insulated or bare equipment grounding conductor installed inside.

Last updated: October 2026

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways

Quick Answer: Metallic raceways like RMC (Article 344) , IMC (Article 342) , and EMT (Article 358) provide high mechanical protection and qualify as equipment grounding conductors (EGCs) under NEC 250.118. EMT must be supported every 10 feet and within 3 feet of each box. Nonmetallic raceways like PVC (Article 352) and RTRC (Article 355) are impervious to rust and corrosive chemicals but require an internal EGC. Schedule 80 PVC is listed for areas subject to physical damage, whereas Schedule 40 PVC is prohibited where subject to physical damage. Across all raceway systems, total bends between pull points cannot exceed 360 degrees .

Selecting the proper raceway involves evaluating structural durability, chemical exposure, ambient temperature, ease of installation, and equipment grounding capability. For the Minnesota journeyman electrician, understanding the mechanical boundaries and securing rules of each conduit system is critical for passing the state licensing examination.

  • Metallic Raceways: RMC, IMC, and EMT
  • Rigid Metal Conduit (Type RMC - NEC Article 344)

Rigid Metal Conduit is the heaviest and most robust raceway recognized in electrical construction. Manufactured from galvanized steel, stainless steel, or aluminum, RMC is threaded at both ends and provides unmatched protection against crushing, severe impact, and projectile puncture.

Permitted Locations (NEC 344.10): Permitted under all atmospheric conditions and occupancies, including severe physical damage environments, hazardous (classified) locations, and direct burial in soil or concrete.

Support Rules (NEC 344.30): Must be securely fastened within 3 feet (900 mm) of each outlet box, junction box, cabinet, or conduit body. Where structural members do not permit fastening within 3 feet, the distance may be extended to 5 feet (1.5 m) . Standard support interval along runs is 10 feet (3.0 m) .

Straight Run Support Extension (Table 344.30(B)(2)): For straight runs of rigid metal conduit made up with threaded couplings, support intervals may be dramatically extended based on trade size:

  • Trade Size 1 / 2 in − 3 / 4 in 1/2\text{ in} - 3/4\text{ in} 1/2 in − 3/4 in : Maximum support spacing 10 feet
  • Trade Size 1 in 1\text{ in} 1 in : Maximum support spacing 12 feet

Trade Size 1 1 4 in − 1 1 2 in 1\frac{1}{4}\text{ in} - 1\frac{1}{2}\text{ in} 1 4 1 ​ in − 1 2 1 ​ in : Maximum support spacing 14 feet

Trade Size 2 in − 2 1 2 in 2\text{ in} - 2\frac{1}{2}\text{ in} 2 in − 2 2 1 ​ in : Maximum support spacing 16 feet

Trade Size 3 in 3\text{ in} 3 in and larger: Maximum support spacing 20 feet

Grounding (NEC 250.118): RMC is fully recognized as an equipment grounding conductor without requiring an internal copper wire, provided all threaded joints are made up wrench-tight.

Intermediate Metal Conduit (Type IMC - NEC Article 342)

Introduced as a lighter-weight alternative to RMC, Intermediate Metal Conduit features a slightly thinner wall profile while utilizing high-strength steel alloy. IMC accepts standard trade-size threaded fittings and delivers comparable mechanical impact performance to RMC at approximately 30 % 30\% 30% less weight.

Permitted Locations (NEC 342.10): Permitted in all occupancies and areas subject to physical damage.

Support Rules (NEC 342.30): Identical to RMC: supported within 3 feet of terminations and every 10 feet along runs, with the same support spacing extensions under Table 342.30(B)(2).

Grounding (NEC 250.118): IMC is listed as an equipment grounding conductor.

Electrical Metallic Tubing (Type EMT - NEC Article 358)

Electrical Metallic Tubing—commonly called "thinwall"—is unthreaded steel or aluminum tubing joined by setscrew or compression couplings. It is the workhorse raceway of commercial interior construction.

Permitted Locations (NEC 358.10): Exposed and concealed in dry, damp, and wet locations (using listed wet-location fittings), and embedded in concrete with approved fittings.

Prohibited Locations (NEC 358.12): Prohibited where subject to severe physical damage . Installing EMT in loading docks where forklifts operate or at bumper level in commercial parking garages is a direct code violation.

Support Rules (NEC 358.30(A)): Must be securely fastened within 3 feet (900 mm) of each outlet box, junction box, cabinet, or fitting. Supports along runs must not exceed 10 feet (3.0 m) . (Exception: Up to 5 feet from terminations where structural framing does not permit 3 feet).

Grounding (NEC 250.118): EMT serves as an equipment grounding conductor when installed with listed fittings that are tightened securely.

  • Nonmetallic Raceways: PVC, RTRC, and LFNC
  • Rigid Polyvinyl Chloride Conduit (Type PVC - NEC Article 352)

PVC conduit is nonconductive, highly resistant to moisture and corrosive chemicals, and lightweight. However, it exhibits a high coefficient of thermal expansion and becomes brittle in freezing temperatures.

  • PVC Specification Schedule 40 PVC Schedule 80 PVC
  • Wall Thickness Standard Heavy Wall (approx. 30–40% thicker)

Physical Damage Rating Prohibited where subject to physical damage (NEC 352.12(C)) Identified and permitted where subject to physical damage (NEC 352.10(F))

  • Internal Cross-Section Standard diameter Reduced internal diameter (lower wire fill capacity)
  • Direct Burial Permitted under Table 300.7 Permitted under Table 300.7
  • Exposed Above Grade Sunlight-resistant listed Sunlight-resistant listed

Support Spacing for PVC (Table 352.30):

  • Trade Size 1 / 2 in − 1 in 1/2\text{ in} - 1\text{ in} 1/2 in − 1 in : 3 feet
  • Trade Size 1 1 4 in − 2 in 1\frac{1}{4}\text{ in} - 2\text{ in} 1 4 1 ​ in − 2 in : 5 feet
  • Trade Size 2 1 2 in − 3 in 2\frac{1}{2}\text{ in} - 3\text{ in} 2 2 1 ​ in − 3 in : 6 feet
  • Trade Size 3 1 2 in − 5 in 3\frac{1}{2}\text{ in} - 5\text{ in} 3 2 1 ​ in − 5 in : 7 feet
  • Trade Size 6 in 6\text{ in} 6 in : 8 feet

In addition, PVC must be secured within 3 feet (900 mm) of each box, cabinet, or termination.

Grounding (NEC 352.60): Because PVC is an electrical insulator, it cannot serve as an equipment grounding conductor . An insulated or bare equipment grounding conductor must always be pulled inside the raceway.

Reinforced Thermosetting Resin Conduit (Type RTRC - NEC Article 355)

RTRC, commonly referred to as fiberglass conduit, is manufactured by winding continuous glass filaments impregnated with epoxy resin. It provides exceptional corrosion resistance in industrial wastewater and chemical plants and has a lower coefficient of thermal expansion than PVC (Table 355.44). RTRC marked -XW is identified for areas of physical damage. Support spacing is governed by Table 355.30 .

Liquidtight Flexible Nonmetallic Conduit (Type LFNC - NEC Article 356)

LFNC consists of a smooth inner nonmetallic core and an oil-resistant, water-resistant outer jacket. It is commonly used for outdoor air conditioning condensing units and motor terminations where vibration or liquid exposure is present.

Support Rules (NEC 356.30): Must be securely fastened at intervals not exceeding 3 feet (900 mm) and within 12 inches (300 mm) on each side of every box, cabinet, or fitting, with exceptions for fishing, lengths of not more than 3 feet at terminals where flexibility is needed, and luminaire whips in accessible ceilings.

Master Raceway Engineering Comparison Table

Raceway Type NEC Article Permitted in Severe Physical Damage? Standard Support Interval Maximum Distance to Box Usable as Equipment Grounding Conductor?

  • RMC (Rigid Metal) 344 Yes 10 ft (up to 20 ft straight runs) 3 ft Yes (NEC 250.118)
  • IMC (Intermediate Metal) 342 Yes 10 ft (up to 20 ft straight runs) 3 ft Yes (NEC 250.118)
  • EMT (Thinwall Tubing) 358 Yes, except severe damage 10 ft 3 ft Yes (NEC 250.118)
  • PVC Schedule 40 352 No 3 ft to 8 ft (by trade size) 3 ft No (Separate EGC required)
  • PVC Schedule 80 352 Yes 3 ft to 8 ft (by trade size) 3 ft No (Separate EGC required)
  • RTRC (Fiberglass) 355 Yes (XW Grade) 3 ft to 8 ft (by trade size) 3 ft No (Separate EGC required)

LFMC (Liquidtight Metal) 350 No 4 1 2 ft 4\frac{1}{2}\text{ ft} 4 2 1 ​ ft 12 in Conditional (trade size ⅜–½: circuits ≤ 20 A \le 20\text{A} ≤ 20 A ; ¾–1¼: ≤ 60 A \le 60\text{A} ≤ 60 A ; 6 ft max total; not where flexibility is needed)

  • LFNC (Liquidtight Nonmetallic) 356 No 3 ft 12 in No (Separate EGC required)
  • The 360-Degree Bend Rule and Pull Point Architecture

Under NEC Sections 344.26 (RMC) , 342.26 (IMC) , 358.26 (EMT) , and 352.26 (PVC) , the total degrees of bends in a single raceway run between pull points must not exceed 360 degrees .

Total Bends = ∑ θ ≤ 360 ∘ ( e.g., Four 90 ∘ Bends, or Two 90 ∘ + Four 45 ∘ Bends ) \text{Total Bends} = \sum \theta \le 360^\circ \quad (\text{e.g., Four } 90^\circ \text{ Bends, or Two } 90^\circ + \text{Four } 45^\circ \text{ Bends}) Total Bends = ∑ θ ≤ 36 0 ∘ ( e.g., Four 9 0 ∘ Bends, or Two 9 0 ∘ + Four 4 5 ∘ Bends )

Every degree of bend increases the frictional pulling tension and elevates the sidewall bearing pressure (SWBP) exerted on the conductor insulation as it rides along the inside radius of the elbow. If a run requires more than 360 degrees of bends, the installer must insert an intermediate pull box, conduit body (Type C, LB, LL, LR, or T), or junction box to serve as a designated pull point.