Study guide
13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314)
Minnesota Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Minnesota Exam, Licensing & Electrical Law
1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement
2 Electrical Theory, Math & Power Calculations
2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting
3 NEC Structure & General Requirements
3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)
4 Conductors, Identification & Ampacity
4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors
5 Branch Circuits, GFCI/AFCI & Required Outlets
5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)
6 Load Calculations (2026 NEC Article 120)
6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)
7 Feeders, Outside Wiring & Services
7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)
8 Overcurrent Protection
8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction
9 System Grounding & Grounding Electrodes
9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems
10 Bonding & Equipment Grounding
10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding
11 General Wiring Methods & Underground Installations
11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)
12 Raceways, Cables & Conduit Fill
12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)
13 Boxes, Conduit Bodies & Cabinets
13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)
14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances
14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)
15 Motors, Controllers & Air Conditioning
15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)
16 Transformers, Generators & Equipment Over 1000 Volts
16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)
17 Hazardous (Classified) Locations
17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)
18 Health Care, Assembly, Agricultural & Mobile Occupancies
18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)
19 Signs, Elevators, Pools, Solar & Other Specific Equipment
19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)
20 Emergency, Standby & Interconnected Power Sources
20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)
21 Limited-Energy, Fire Alarm & Communications Systems
21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)
13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314)
Key Takeaways Explain This Topic AI
In walls or ceilings of noncombustible material, the front edge of a box may be set back not more than ¼ in. from the finished surface; in combustible material it must be flush or project (314.20).
Gaps or open spaces around boxes in plaster, drywall, or plasterboard may not exceed ⅛ in. at the edge of the box (314.21).
A box supported only by raceways needs two or more threaded conduits secured within 3 ft of the box, or within 18 in. if the box contains a device or supports a luminaire (314.23(E) and (F)).
Outlet boxes for luminaires may support up to 50 lb unless listed and marked for a greater weight, and paddle fans require boxes listed for fan support, up to 70 lb (314.27).
Boxes must be installed so the wiring inside can be reached without removing any part of the building, sidewalks, paving, or earth (314.29).
Last updated: October 2026
Why box installation is tested
DLI's knowledge areas include outlet, device, pull, and junction boxes and their support . Inspectors write correction orders for recessed boxes, loose boxes, and fans hung on standard boxes, and exam questions often turn on one dimension: ¼ in., ⅛ in., 18 in., 3 ft, 50 lb, or 70 lb.
Box types and materials
314.3 Nonmetallic boxes: used only with open wiring on insulators, concealed knob-and-tube, cabled wiring methods with entirely nonmetallic sheaths, flexible cords, and nonmetallic raceways, unless internal bonding is provided between all entries or the box is listed for metal raceways.
314.4 Metal boxes: must be grounded and bonded under Article 250.
314.15 Damp or wet locations: boxes, conduit bodies, and fittings must prevent moisture from entering or accumulating, and boxes in wet locations must be listed for wet locations. Field drainage openings between ⅛ in. and ¼ in. are permitted in boxes listed for damp or wet locations. The 2026 NEC 250.64(G) prohibits routing a grounding electrode conductor through such openings.
Conductors entering boxes (314.17)
Openings through which conductors enter must be closed in a manner identified for the application.
Where cable is used, each cable must be secured to the box, except as follows: with nonmetallic-sheathed cable and single-gang boxes not larger than 2¼ in. × 4 in. mounted in walls or ceilings, the cable may be fastened within 8 in. of the box instead of with a clamp, if the sheath extends at least ¼ in. inside the box.
In nonmetallic boxes, the cable sheath must extend at least ¼ in. inside the box beyond any cable clamp.
Box position in walls and ceilings (314.20 and 314.21)
Wall or ceiling material Rule
Noncombustible (such as drywall over steel studs, plaster, masonry) The box or extension ring may be set back not more than ¼ in.
Combustible (such as wood paneling) The box must be flush with the finished surface or project from it
Repairing gaps (314.21) Plaster, drywall, or plasterboard surfaces that are broken or incomplete around boxes must be repaired so there are no gaps larger than ⅛ in. at the box edge
Surface extensions (314.22) Made by mounting and mechanically securing an extension ring over the box, with EGC continuity maintained
Supporting boxes (314.23)
- Mounting Requirement
- (A) Surface Fastened to the surface; if the surface cannot provide support, use another method
(B) Structural mounting Nails and screws passing through the box interior must be within ¼ in. of the back or ends of the box; braces must be metal at least 0.020 in. thick or wood at least 1 in. × 2 in.
(C) Mounting in finished surfaces Secured by clamps, anchors, or fittings identified for the application
(D) Suspended ceilings Fastened to the ceiling framing members, which are securely fastened to each other and to the building structure, or supported by identified support wires
(E) Raceway-supported, no devices or luminaires Supported by two or more conduits threaded wrenchtight into the box or hubs, each secured within 3 ft of the box
(F) Raceway-supported, with devices or luminaires Supported by two or more conduits threaded wrenchtight, each secured within 18 in. of the box
(G) Concrete or masonry Identified as suitably protected from corrosion and securely embedded
(H) Pendant boxes Supported by multiconductor cord or cable with strain relief, or by conduit stems with set screws or locknuts
A single EMT or a single conduit is never enough to support a box by itself under (E) or (F).
Box depth (314.24)
Outlet and device boxes must have enough depth for the equipment installed. A box that does not enclose devices or utilization equipment must be at least ½ in. deep. A box that encloses devices or utilization equipment and conductors 12 AWG or smaller must be at least 15/16 in. deep, and larger equipment and conductors need more depth.
Luminaire, fan, and floor boxes (314.27)
Use Requirement
Wall luminaire boxes Marked on the interior with the maximum weight if they support more than 50 lb; otherwise a wall box may support a luminaire of up to 50 lb
Ceiling luminaire outlets Boxes designed to support luminaires of at least 50 lb ; heavier luminaires need a box listed and marked for the weight, or must be supported independently
Floor boxes Listed specifically for floor applications
Ceiling-suspended paddle fans Outlet boxes listed for the sole support of fans; a box must be marked if listed for fans heavier than 35 lb , and the maximum supported weight is 70 lb
Utilization equipment Boxes must be designed to support the equipment's weight, such as heavy ceiling-mounted equipment
Spare fan-ready outlets in dwellings Where spare, separately switched ungrounded conductors are run to a ceiling outlet box in a location acceptable for a paddle fan in a one-family, two-family, or multifamily dwelling, the box must be listed for the sole support of a paddle fan
Accessibility (314.29)
Boxes, conduit bodies, and handhole enclosures must be installed so the wiring in them can be reached without removing any part of the building , or, in underground circuits, without excavating sidewalks, paving, earth, or other substances used to establish finished grade. Listed boxes and handhole enclosures may be covered by gravel, light aggregate, or noncohesive granulated soil if their location is effectively identified and accessible for excavation. A box above a lift-out ceiling panel is accessible; a box buried behind drywall is not.
Handhole enclosures (314.30) must be designed and installed to withstand all expected loads; covers must carry an identifying mark or logo showing electrical use, and covers over 100 lb or otherwise requiring tools to open.
Worked example: two boxes on a warehouse wall
A junction box with no devices is supported only by two ¾ in. RMC conduits threaded into its hubs. Each conduit must be secured within 3 ft of the box. A single conduit is not enough.
A weatherproof receptacle box on the same wall is supported only by two threaded RMC conduits. Because it contains a device , each conduit must be secured within 18 in. of the box.