Study guide

13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28)

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28)

Key Takeaways Explain This Topic AI

NEC 314.28 governs the minimum sizing of all pull boxes, junction boxes, and conduit bodies enclosing conductors 4 AWG and larger operating at 1,000 volts nominal or less.

For straight pulls under NEC 314.28(A)(1), the length of the box must not be less than 8 times the trade size of the largest raceway entering the enclosure ( L ≥ 8 × D largest L \ge 8 \times D_{\text{largest}} L ≥ 8 × D largest ​ ).

For angle pulls, U-pulls, and splices under NEC 314.28(A)(2), the distance between each raceway entry and the opposite wall must not be less than 6 times the trade size of the largest raceway entering that wall, plus the sum of the trade sizes of all other raceways on that same wall ( D ≥ 6 × D largest + ∑ D other D \ge 6 \times D_{\text{largest}} + \sum D_{\text{other}} D ≥ 6 × D largest ​ + ∑ D other ​ ).

For angle and U-pulls, the distance between raceway entries enclosing the same conductor must not be less than 6 times the trade size of the larger raceway ( S ≥ 6 × D S \ge 6 \times D S ≥ 6 × D ), measured between entry centerlines or edges.

Box depth is determined by the size and locknut spacing of raceways, or where conductors enter opposite a removable cover, the wire bending space requirements of NEC Table 312.6(A) apply.

Last updated: October 2026

13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28)

Quick Answer: Under NEC 314.28 , pull and junction boxes enclosing conductors 4 AWG or larger are sized based on raceway trade sizes rather than cubic-inch volume. For straight pulls (NEC 314.28(A)(1)), the minimum box length is 8 times the trade size of the largest raceway ( L ≥ 8 × D largest L \ge 8 \times D_{\text{largest}} L ≥ 8 × D largest ​ ). For angle pulls, U-pulls, and splices (NEC 314.28(A)(2)), the distance to the opposite wall must be not less than 6 times the largest raceway plus the sum of all other raceways on that wall ( D ≥ 6 × D largest + ∑ D other D \ge 6 \times D_{\text{largest}} + \sum D_{\text{other}} D ≥ 6 × D largest ​ + ∑ D other ​ ). Additionally, the separation between raceways enclosing the same conductor must be at least 6 times the trade size of the raceway ( S ≥ 6 × D S \ge 6 \times D S ≥ 6 × D ).

When pulling heavy conductors—such as 4 AWG through 750 kcmil feeders—substantial mechanical tension is exerted by pulling ropes and tuggers. If a junction box or pull box is undersized, the conductors are forced through tight bends that crush or stretch the thermoplastic insulation, cause phase-to-ground faults, or fracture copper strands. To guarantee adequate physical bending radius and pulling clearance, NEC Section 314.28 establishes rigid dimensional mandates for pull boxes, junction boxes, and conduit bodies operating at 1,000 volts or less.

On the Minnesota Journeyworker examination, pull box calculations are among the most frequently tested calculation topics. Candidates must navigate straight pulls, angle pulls, U-pulls, and complex multi-wall combination enclosures with absolute mathematical precision.

Scope & The 4 AWG Threshold (NEC 314.28)

The sizing requirements of Section 314.28 apply to all enclosures—including pull boxes, junction boxes, sheet metal troughs, and conduit bodies—under two conditions:

The enclosure contains conductors 4 AWG or larger ; and

The system operates at 1,000 volts nominal or less .

Key Distinction: If an enclosure contains only conductors smaller than 4 AWG (such as 14, 12, 10, 8, or 6 AWG), its dimensions are governed strictly by the cubic-inch box fill calculations of NEC 314.16 . However, if even a single conductor 4 AWG or larger enters the enclosure, NEC 314.28 governs the length, width, and depth of the box .

Straight Pull Calculations (NEC 314.28(A)(1))

A straight pull occurs where conductors enter one wall of an enclosure and exit through the opposite wall in a direct, straight alignment without making a directional bend or turn.

The 8X Straight Pull Rule

Under NEC 314.28(A)(1) , the length of the box shall not be less than 8 times the metric designator (trade size) of the largest raceway :

Minimum Length (Straight Pull) = 8 × D largest raceway \text{Minimum Length (Straight Pull)} = 8 \times D_{\text{largest raceway}} Minimum Length (Straight Pull) = 8 × D largest raceway ​

Critical Straight Pull Rules:

Only the Largest Raceway Dictates Length: Other raceways entering the same wall are completely ignored when determining the length of a straight pull box. For example, if a wall contains one 4-inch conduit, one 3-inch conduit, and three 2-inch conduits, the minimum length is based solely on the 4-inch conduit: 8 × 4 in = 32 in 8 \times 4\text{ in} = 32\text{ in} 8 × 4 in = 32 in .

Conductor Size Does Not Dictate Length: The calculation uses the conduit trade size , not the size of the conductors inside the conduit.

Box Width and Depth: The width and depth of a straight pull box must be sufficient to maintain proper spacing between locknuts and bushings under NEC 312.6 and manufacturer specifications, allowing adequate mechanical clearance for conduit wrenches.

Angle Pulls, U-Pulls & Splices (NEC 314.28(A)(2))

An angle pull occurs where conductors enter one wall and exit through an adjacent wall (such as entering the top and exiting the right side, forming a 90-degree bend). A U-pull occurs where conductors enter a wall and exit through the same wall. When conductors are spliced within an enclosure (even if conduits are arranged on opposite walls), the enclosure must be sized under the angle pull rules because conductors must be looped and bent to make the splices.

1. Distance to Opposite Wall (The 6X Plus Sum Rule)

Under NEC 314.28(A)(2) , the distance between each raceway entry inside the box and the opposite wall must not be less than 6 times the trade size of the largest raceway , plus the sum of the trade sizes of all other raceway entries on the same wall:

D wall = ( 6 × D largest raceway ) + ∑ D other raceways on same wall D_{\text{wall}} = (6 \times D_{\text{largest raceway}}) + \sum D_{\text{other raceways on same wall}} D wall ​ = ( 6 × D largest raceway ​ ) + ∑ D other raceways on same wall ​

This calculation must be performed independently for every wall of the enclosure.

The largest wall calculation determines the minimum dimension of the box in that axis.

Only raceways in the same row on that wall are summed. If raceways enter in multiple rows, see the multiple-row rules below.

2. Distance Between Raceway Entries (The 6X Separation Rule)

Under NEC 314.28(A)(2) , the distance between raceway entries enclosing the same conductor must not be less than 6 times the metric designator (trade size) of the larger raceway :

S ≥ 6 × D larger raceway S \ge 6 \times D_{\text{larger raceway}} S ≥ 6 × D larger raceway ​

The Code does not spell out the measuring points. Measuring from the nearest edge of one entry to the nearest edge of the other gives the most conservative result.

For an angle pull, this is the diagonal distance across the corner of the box ( S = X 2 + Y 2 S = \sqrt{X^2 + Y^2} S = X 2 + Y 2 ​ ).

If the box dimensions calculated from the opposite-wall rule do not provide sufficient diagonal distance across the corner to satisfy the 6 X 6X 6 X separation requirement, the box must be enlarged until the 6 X 6X 6 X diagonal spacing is achieved!

U-Pulls (Entering and Exiting the Same Wall)

In a U-pull , conductors enter a wall and exit through the same wall. The minimum distance to the opposite wall is determined by the same formula:

Distance to Opposite Wall (U-Pull) = ( 6 × D largest raceway ) + ∑ D other raceways on that wall \text{Distance to Opposite Wall (U-Pull)} = (6 \times D_{\text{largest raceway}}) + \sum D_{\text{other raceways on that wall}} Distance to Opposite Wall (U-Pull) = ( 6 × D largest raceway ​ ) + ∑ D other raceways on that wall ​

Additionally, the distance between the raceway entry and raceway exit for the same conductors on that wall must be not less than 6 times the trade size of the raceway ( S ≥ 6 × D S \ge 6 \times D S ≥ 6 × D ), measured between centerlines.

  • Multiple Rows of Raceways & Enclosure Depth
  • Multiple Rows of Conduits (NEC 314.28(A)(2))

Where raceways enter a wall in more than one row (for example, two stacked rows of conduits), each row is calculated individually : 6 times the largest raceway in that row plus the sum of the other raceways in that row. The single row that gives the greatest distance sets the dimension.

Enclosure Depth & Removable Covers (NEC 314.28(A)(2) Exception)

What dictates the depth (front-to-back dimension) of a pull box? Under standard conditions, depth must be sufficient to accommodate conduit locknuts, bushings, and conductor bending radii. Under the exception to NEC 314.28(A)(2) , where a raceway or cable entry is in the wall opposite a removable cover , the distance from that wall to the cover is permitted to be only the wire bending space in NEC Table 312.6(A) for one wire per terminal, instead of the full 6X angle-pull distance.

  • Conductor Size Entering Opposite Cover Minimum Box Depth (NEC Table 312.6(A))
  • 4 AWG to 3 AWG 2.0 inches 2.0\text{ inches} 2.0 inches ( 50.8 mm 50.8\text{ mm} 50.8 mm )
  • 2 AWG 2.5 inches 2.5\text{ inches} 2.5 inches ( 63.5 mm 63.5\text{ mm} 63.5 mm )
  • 1 AWG 3.0 inches 3.0\text{ inches} 3.0 inches ( 76.2 mm 76.2\text{ mm} 76.2 mm )
  • 1/0 to 2/0 AWG 3.5 inches 3.5\text{ inches} 3.5 inches ( 88.9 mm 88.9\text{ mm} 88.9 mm )
  • 3/0 to 4/0 AWG 4.0 inches 4.0\text{ inches} 4.0 inches ( 102 mm 102\text{ mm} 102 mm )
  • 250 kcmil 4.5 inches 4.5\text{ inches} 4.5 inches ( 114 mm 114\text{ mm} 114 mm )
  • 300 to 350 kcmil 5.0 inches 5.0\text{ inches} 5.0 inches ( 127 mm 127\text{ mm} 127 mm )
  • 400 to 500 kcmil 6.0 inches 6.0\text{ inches} 6.0 inches ( 152 mm 152\text{ mm} 152 mm )
  • 600 to 700 kcmil 8.0 inches 8.0\text{ inches} 8.0 inches ( 203 mm 203\text{ mm} 203 mm )
  • 750 to 900 kcmil 8.0 inches 8.0\text{ inches} 8.0 inches ( 203 mm 203\text{ mm} 203 mm )
  • Step-by-Step Worked Pull Box Calculations
  • Example 1: Straight Pull Box Sizing

A feeder raceway system contains one 4-inch conduit, two 3-inch conduits, and one 2-inch conduit entering the left wall of a pull box and exiting through the right wall in a straight pull. All conductors are 350 kcmil THHN copper. What is the minimum required length of the pull box?

Analysis: Under NEC 314.28(A)(1), for a straight pull, the length is determined solely by multiplying 8 times the trade size of the largest raceway.

Largest raceway = 4 inches 4\text{ inches} 4 inches .

Other raceways ( 3 in 3\text{ in} 3 in , 2 in 2\text{ in} 2 in ) are not added in a straight pull!

Minimum Box Length = 8 × 4 in = 32 inches \text{Minimum Box Length} = 8 \times 4\text{ in} = \mathbf{32\text{ inches}} Minimum Box Length = 8 × 4 in = 32 inches

Example 2: Angle Pull Box Sizing with Asymmetric Walls

A junction box is installed for an angle pull where conductors turn 90 degrees. Conduits enter through the top wall and exit through the right wall:

Top Wall Entries: One 3-inch conduit, one 2.5-inch conduit, and two 1.5-inch conduits.

Right Wall Exits: One 3-inch conduit, one 2.5-inch conduit, and two 1.5-inch conduits.

The conductors in the 3-inch conduits enter the top and exit the right.

Step 1: Calculate Distance from Top Wall to Opposite (Bottom) Wall

Using NEC 314.28(A)(2), take 6 times the largest raceway on the top wall, plus the sum of all other raceways entering that same top wall:

D Top to Bottom = ( 6 × 3 in ) + 2.5 in + 1.5 in + 1.5 in = 18 in + 5.5 in = 23.5 inches D_{\text{Top to Bottom}} = (6 \times 3\text{ in}) + 2.5\text{ in} + 1.5\text{ in} + 1.5\text{ in} = 18\text{ in} + 5.5\text{ in} = \mathbf{23.5\text{ inches}} D Top to Bottom ​ = ( 6 × 3 in ) + 2.5 in + 1.5 in + 1.5 in = 18 in + 5.5 in = 23.5 inches

Step 2: Calculate Distance from Right Wall to Opposite (Left) Wall

Using NEC 314.28(A)(2), take 6 times the largest raceway on the right wall, plus the sum of all other raceways on that wall:

D Right to Left = ( 6 × 3 in ) + 2.5 in + 1.5 in + 1.5 in = 18 in + 5.5 in = 23.5 inches D_{\text{Right to Left}} = (6 \times 3\text{ in}) + 2.5\text{ in} + 1.5\text{ in} + 1.5\text{ in} = 18\text{ in} + 5.5\text{ in} = \mathbf{23.5\text{ inches}} D Right to Left ​ = ( 6 × 3 in ) + 2.5 in + 1.5 in + 1.5 in = 18 in + 5.5 in = 23.5 inches

Step 3: Check Separation Distance Between Conduits Enclosing Same Conductors

The conductors in the 3-inch conduit enter the top and exit the right. Under NEC 314.28(A)(2), the distance between those two raceway entries must be not less than 6 times the trade size:

S ≥ 6 × 3 in = 18 inches S \ge 6 \times 3\text{ in} = \mathbf{18\text{ inches}} S ≥ 6 × 3 in = 18 inches

If the 3-inch conduits are positioned near the far corners of the 23.5 × 23.5 23.5 \times 23.5 23.5 × 23.5 inch box, the diagonal distance easily exceeds 18 inches ( D diag ≈ 20 2 + 20 2 ≈ 28.3 in ≥ 18 in D_{\text{diag}} \approx \sqrt{20^2 + 20^2} \approx 28.3\text{ in} \ge 18\text{ in} D diag ​ ≈ 2 0 2 + 2 0 2 ​ ≈ 28.3 in ≥ 18 in ). Therefore, a 24 × 24 24 \times 24 24 × 24 inch standard junction box satisfies all code requirements.

Example 3: Combination Pull Box (Straight Pull and Angle Pull)

A pull box contains both a straight pull and an angle pull:

Left Wall: One 4-inch conduit (pulls straight through to right wall) and one 2-inch conduit (turns 90 degrees to exit the bottom wall).

Right Wall: One 4-inch conduit (straight pull from left wall).

Bottom Wall: One 2-inch conduit (angle pull from left wall).

Step 1: Calculate Horizontal Dimension (Left Wall to Right Wall)

Straight Pull Requirement: The 4-inch conduit makes a straight pull between left and right walls: L straight = 8 × 4 in = 32 inches L_{\text{straight}} = 8 \times 4\text{ in} = \mathbf{32\text{ inches}} L straight ​ = 8 × 4 in = 32 inches

Angle Pull Requirement on Left Wall: The left wall also contains an angle pull conduit (2-inch). The distance from the left wall to the opposite (right) wall must satisfy: D angle = ( 6 × 4 in ) + 2 in = 24 in + 2 in = 26 inches D_{\text{angle}} = (6 \times 4\text{ in}) + 2\text{ in} = 24\text{ in} + 2\text{ in} = \mathbf{26\text{ inches}} D angle ​ = ( 6 × 4 in ) + 2 in = 24 in + 2 in = 26 inches

Governing Horizontal Dimension: The box length must satisfy the larger of the two requirements: max ⁡ ( 32 in , 26 in ) = 32 inches \max(32\text{ in}, 26\text{ in}) = \mathbf{32\text{ inches}} max ( 32 in , 26 in ) = 32 inches .

Step 2: Calculate Vertical Dimension (Top Wall to Bottom Wall)

The bottom wall contains one 2-inch conduit making an angle pull to the left wall.

Distance from bottom wall to opposite (top) wall: D vertical = 6 × 2 in = 12 inches D_{\text{vertical}} = 6 \times 2\text{ in} = \mathbf{12\text{ inches}} D vertical ​ = 6 × 2 in = 12 inches

Step 3: Check Separation Distance for Angle Pull Conductors

The 2-inch conduits enter left and exit bottom. Minimum centerline separation: S = 6 × 2 in = 12 inches S = 6 \times 2\text{ in} = \mathbf{12\text{ inches}} S = 6 × 2 in = 12 inches

Step 4: Final Dimensions

The minimum required box dimensions are 32 inches long × 12 inches high 32\text{ inches long} \times 12\text{ inches high} 32 inches long × 12 inches high (with depth sized for conduit locknuts).

  • Practical Exam Scenarios & Trap Avoidance
  • Trap 1: Adding Other Conduits in a Straight Pull

Exam Trap: A question presents a straight pull with one 4-inch conduit and two 2-inch conduits and asks for box length.

Common Error: Calculating ( 8 × 4 ) + 2 + 2 = 36 inches (8 \times 4) + 2 + 2 = 36\text{ inches} ( 8 × 4 ) + 2 + 2 = 36 inches .

Correction: In straight pulls, only 8 times the largest raceway is used . The other raceways are NEVER added for straight pulls. The answer is 8 × 4 = 32 inches 8 \times 4 = 32\text{ inches} 8 × 4 = 32 inches . The addition of other raceways applies exclusively to angle pulls, U-pulls, and splices under NEC 314.28(A)(2).

Trap 2: Neglecting the 6X Separation Rule

Exam Trap: Sizing an angle pull box based purely on the opposite wall formula, resulting in a box where conduit entry holes are punched so close together across the corner that conductors exceed their minimum bending radius.

Correction: Always verify the diagonal separation between conduit entries enclosing the same conductor: S ≥ 6 × D larger S \ge 6 \times D_{\text{larger}} S ≥ 6 × D larger ​ . If entry holes are closer than 6 D 6D 6 D , the box must be enlarged.

Trap 3: Applying 314.28 to Conductors Smaller Than 4 AWG

Exam Trap: A pull box contains six 6 AWG THHN conductors in a 1-inch conduit. Sizing the box as 8 × 1 in = 8 inches 8 \times 1\text{ in} = 8\text{ inches} 8 × 1 in = 8 inches .

Correction: NEC 314.28 applies only to 4 AWG and larger . Conductors 6 AWG and smaller are calculated on cubic-inch box fill under NEC 314.16 or conduit body fill under Chapter 9.