Study guide
14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411)
Minnesota Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Minnesota Exam, Licensing & Electrical Law
1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement
2 Electrical Theory, Math & Power Calculations
2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting
3 NEC Structure & General Requirements
3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)
4 Conductors, Identification & Ampacity
4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors
5 Branch Circuits, GFCI/AFCI & Required Outlets
5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)
6 Load Calculations (2026 NEC Article 120)
6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)
7 Feeders, Outside Wiring & Services
7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)
8 Overcurrent Protection
8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction
9 System Grounding & Grounding Electrodes
9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems
10 Bonding & Equipment Grounding
10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding
11 General Wiring Methods & Underground Installations
11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)
12 Raceways, Cables & Conduit Fill
12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)
13 Boxes, Conduit Bodies & Cabinets
13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)
14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances
14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)
15 Motors, Controllers & Air Conditioning
15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)
16 Transformers, Generators & Equipment Over 1000 Volts
16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)
17 Hazardous (Classified) Locations
17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)
18 Health Care, Assembly, Agricultural & Mobile Occupancies
18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)
19 Signs, Elevators, Pools, Solar & Other Specific Equipment
19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)
20 Emergency, Standby & Interconnected Power Sources
20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)
21 Limited-Energy, Fire Alarm & Communications Systems
21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)
14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411)
Key Takeaways Explain This Topic AI
No cord-connected, chain-, cable-, or cord-suspended luminaires, lighting track, pendants, or paddle fans may be located within 3 ft horizontally and 8 ft vertically from the top of a bathtub rim or shower threshold (410.10(D)).
Closet luminaires must have completely enclosed light sources; incandescent or LED surface luminaires need 12 in. of clearance from the storage space, and recessed or fluorescent luminaires need 6 in. (410.16).
Thermal insulation may not be installed above a recessed luminaire or within 3 in. of its enclosure, wiring compartment, ballast, or driver unless the luminaire is identified as Type IC (410.116(B)).
Tap conductors from an outlet box to a recessed luminaire must be in a suitable raceway or cable at least 18 in. and not more than 6 ft long (410.117(C)).
Lighting track may not be installed less than 5 ft above the finished floor unless protected from physical damage or operating at not over 30 V RMS open-circuit (410.151(C)).
Last updated: October 2026
Why luminaire rules are tested
DLI's knowledge areas include luminaires and lighting . The questions are practical: can a pendant hang over a tub, which luminaire can go in a closet, and how close can insulation be to a can light?
Luminaires in specific locations (410.10)
Wet and damp locations: luminaires must be marked suitable for wet locations or suitable for damp locations , as applicable, and installed so water cannot enter or accumulate in wiring compartments, lampholders, or other electrical parts.
Corrosive locations: use luminaires suitable for the location.
Ducts and hoods: luminaires may be installed in commercial cooking hoods only if identified for that use and meeting specific conditions.
Bathtub and shower areas (410.10(D)): no part of a cord-connected luminaire, chain-, cable-, or cord-suspended luminaire, lighting track, pendant, or ceiling-suspended paddle fan may be located within a zone 3 ft horizontally and 8 ft vertically from the top of the bathtub rim or shower stall threshold, including the space directly over the tub or shower. Luminaires located within the actual outside dimension of the tub or shower up to 8 ft above the rim or threshold must be marked suitable for damp locations, or wet locations where subject to shower spray.
Indoor sports, mixed-use, and all-purpose facilities: luminaires subject to physical damage need guards or protection.
Clothes closets (410.16)
Permitted: surface-mounted or recessed incandescent or LED luminaires with completely enclosed light sources; surface-mounted or recessed fluorescent luminaires; and surface-mounted fluorescent or LED luminaires identified as suitable for installation within the closet storage space.
Not permitted: incandescent luminaires with open or partially enclosed lamps, and pendant luminaires or lampholders.
Luminaire type Minimum clearance from the closet storage space
Surface-mounted incandescent or LED, completely enclosed source, on the wall above the door or on the ceiling 12 in.
Surface-mounted fluorescent, on the wall above the door or on the ceiling 6 in.
Recessed incandescent or LED with completely enclosed source, in the wall or ceiling 6 in.
Recessed fluorescent, in the wall or ceiling 6 in.
Surface-mounted fluorescent or LED identified for use in the storage space Permitted within the storage space
The storage space is the volume from the floor to 6 ft (or the highest clothes-hanging rod) and 24 in. from the side and back walls (or the width of the shelf, if greater), plus the space above that to the ceiling 12 in. or the shelf width deep.
Supporting luminaires (410.30 to 410.36)
A luminaire weighing more than 6 lb or exceeding 16 in. in any dimension may not be supported by the screw shell of a lampholder.
Outlet boxes may support luminaires within the limits of 314.27 (generally up to 50 lb ).
In suspended ceilings , framing members used to support luminaires must be securely fastened to each other and to the building structure, and luminaires must be fastened to the framing by bolts, screws, rivets, or listed clips identified for the ceiling framing.
Outdoor luminaires may be supported by trees (410.36(G)), although trees may not support overhead conductor spans (225.26).
Exposed conductive parts of luminaires must be connected to an EGC, and the screw shell of a lampholder must be connected to the grounded conductor.
Cord-connected luminaires and luminaires as raceways
Cord-connected luminaires (410.62): electric-discharge and LED luminaires may be cord-connected where the luminaire is located directly below its outlet box or busway, the cord is visible for its entire length outside the luminaire, the cord is not subject to strain or physical damage, and the cord ends in a grounding-type attachment plug or busway plug (or is part of a listed assembly with a manufactured wiring system connector). Adjustable luminaires that need aiming may use a hard-usage cord no longer than needed for adjustment.
Luminaires as raceways (410.64): luminaires may not be used as raceways for circuit conductors unless listed and marked for use as a raceway. Luminaires designed for end-to-end connection to form a continuous assembly, or luminaires connected together by recognized wiring methods, may carry the conductors of one two-wire branch circuit, or one multiwire branch circuit , supplying the connected luminaires, plus one additional two-wire branch circuit that separately supplies one or more of them.
Recessed luminaires (410.110 to 410.117)
Rule Requirement
Clearance from combustibles (410.116(A)) Non-Type IC recessed luminaires: at least ½ in. from combustible materials, except at points of support
Thermal insulation (410.116(B)) Insulation may not be above a recessed luminaire or within 3 in. of its enclosure, wiring compartment, ballast, transformer, LED driver, or power supply, unless the luminaire is identified as Type IC (insulation contact)
Temperature of supply conductors (410.117(A)) Conductors with insulation suitable for the temperature encountered
Tap conductors (410.117(C)) From the outlet box to the luminaire's terminal housing in a suitable raceway or cable at least 18 in. and not more than 6 ft long
Electric-discharge and LED luminaires
Luminaires with ballasts, transformers, or LED drivers must have those components listed and protected as required, and auxiliary equipment not part of the luminaire must be enclosed in accessible, permanently installed metal cabinets.
Disconnecting means (410.130(G)): in indoor locations other than dwellings and their accessory structures, fluorescent luminaires using double-ended lamps with ballasts that can be serviced in place need a disconnecting means , inside or outside each luminaire, accessible to qualified persons before servicing the ballast; on multiwire branch circuits it must open all supply conductors, including the grounded conductor, simultaneously. When a ballast is replaced in an existing luminaire without one, a disconnecting means must be added.
Electric-discharge lighting over 1000 V (Article 410, Part XIII)
Systems with an open-circuit voltage over 1000 V , such as some neon installations, may not be installed in or on dwelling occupancies. Transformers must be listed and enclosed, with limited secondary voltage and current, and each luminaire or group must be controlled by an externally operable switch or circuit breaker that opens all ungrounded primary conductors and is within sight or lockable. Article 600 adds requirements for neon signs.
Lighting track (Article 410, Part XIV)
Rule Requirement
Not installed Where likely to be subjected to physical damage; in wet or damp locations; where subject to corrosive vapors; in storage battery rooms; in hazardous locations; where concealed; through walls or partitions; less than 5 ft above the finished floor unless protected or operating at 30 V RMS or less; within the tub and shower zone of 410.10(D)
Support A single track section 4 ft or shorter needs two supports; each additional section of 4 ft or shorter needs at least one more
Load Track lighting adds 150 VA per 2 ft in nondwelling load calculations (120.43(B))
Connected load May not exceed the track rating, and the track must be supplied by a branch circuit with a rating not greater than the track
Low-voltage lighting systems (Article 411)
Lighting systems operating at 30 V AC or less (or 60 V DC or less), such as landscape and cable lighting, must be listed or assembled from listed parts. They:
must be supplied by an isolating transformer or listed power supply, from a branch circuit rated not more than 25 A ;
may not be concealed or run through a building wall unless installed with a Chapter 3 wiring method or Class 2 wiring; and
may not be installed within 10 ft horizontally of pools, spas, fountains, or similar bodies of water, unless permitted by Article 680; and
must have secondary circuits that are not grounded (Article 411).
Worked example: a bathroom remodel
A homeowner wants a pendant over the tub, recessed cans in the ceiling, and a closet light.
Pendant over the tub: not permitted anywhere within 3 ft horizontally and 8 ft vertically of the tub rim, including directly over it.
Recessed can over the shower: permitted if marked suitable for wet locations, because it is within the shower's footprint and subject to spray. If the attic above is insulated, use Type IC cans or keep insulation 3 in. away.
Closet light: a surface LED luminaire with a completely enclosed source on the ceiling must be at least 12 in. from the storage space; a recessed LED needs 6 in.