Study guide

15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52)

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52)

Key Takeaways Explain This Topic AI

Motor branch-circuit short-circuit and ground-fault protective devices (SCGF OCPDs) protect conductors and equipment against high-magnitude faults, not motor overloads.

Maximum branch-circuit SCGF device ratings are calculated by multiplying the motor Table FLC by the percentages in NEC Table 430.52: Nontime-delay fuses at 300%, Dual-element (time-delay) fuses at 175%, Instantaneous trip breakers at 800%, and Inverse-time breakers at 250%.

Under NEC 430.52(C)(1) Exception No. 1, if the calculated value does not correspond to a standard ampere rating listed in NEC 240.6(A), the next higher standard ampere rating is permitted.

Under NEC 430.52(C)(1) Exception No. 2, if the standard rating from Exception 1 is incapable of carrying starting current, maximum ratings can be increased: dual-element fuses up to 225%, inverse-time breakers up to 400% (for FLC ≤ \le ≤ 100A) or 300% (for FLC > 100A), and nontime-delay fuses up to 400%.

Instantaneous trip circuit breakers (motor circuit protectors / MCPs) lack thermal overload elements and are permitted only as part of a listed combination motor controller assembly under NEC 430.52(C)(3).

Last updated: October 2026

15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52)

Quick Answer: Under NEC Table 430.52 , the maximum rating or setting of a motor branch-circuit short-circuit and ground-fault (SCGF) protective device is calculated as a percentage of the motor's Table FLC (from Tables 430.248–430.250): 300% for nontime-delay fuses, 175% for dual-element (time-delay) fuses, 250% for inverse-time circuit breakers, and 800% for instantaneous trip circuit breakers. Under NEC 430.52(C)(1) Exception No. 1 , if the calculated value does not match a standard ampere rating in NEC 240.6(A) , the next higher standard rating is permitted.

In standard electrical wiring, overcurrent protective devices (OCPDs) are sized to protect conductors from both sustained overloads and short circuits. For example, a 12 AWG copper branch circuit is normally restricted to a 20-ampere circuit breaker under NEC 240.4(D) . However, applying this general rule to electric motors is impossible: during starting, an induction motor draws an inrush of 6 × 6 \times 6 × to 8 × 8 \times 8 × its full-load current for several seconds while accelerating the connected mechanical inertia. A standard 20A thermal-magnetic breaker protecting a motor with a 16A full-load running current would trip instantaneously every time the motor attempted to start.

To overcome this physical reality, the National Electrical Code decouples overcurrent protection into two separate elements: Part III Overloads handle motor running overcurrents, while Part IV SCGF Devices are sized with substantial headroom to absorb locked-rotor starting currents while remaining ready to clear catastrophic phase-to-phase short circuits and ground faults.

Maximum Rating of SCGF Devices (NEC Table 430.52)

Under NEC 430.52(B) and 430.52(C) , the motor branch-circuit short-circuit and ground-fault protective device shall have a rating or setting not exceeding the percentages of motor Table Full-Load Current listed in NEC Table 430.52 :

Type of Motor Nontime Delay Fuse Dual Element (Time-Delay) Fuse Instantaneous Trip Breaker Inverse Time Breaker

Single-Phase Motors 300 % 300\% 300% 175 % 175\% 175% 800 % 800\% 800% 250 % 250\% 250%

Polyphase AC (Squirrel-Cage, Other than Design B Energy Efficient) 300 % 300\% 300% 175 % 175\% 175% 800 % 800\% 800% 250 % 250\% 250%

Polyphase AC (Design B Energy Efficient) 300 % 300\% 300% 175 % 175\% 175% 1100 % 1100\% 1100% 250 % 250\% 250%

  • Synchronous Motors 300 % 300\% 300% 175 % 175\% 175% 800 % 800\% 800% 250 % 250\% 250%
  • Wound-Rotor Motors 150 % 150\% 150% 150 % 150\% 150% 800 % 800\% 800% 150 % 150\% 150%
  • Direct-Current Motors (Constant Voltage) 150 % 150\% 150% 150 % 150\% 150% 250 % 250\% 250% 150 % 150\% 150%
  • The Operating Principles of Each Protective Device Type

Inverse-Time Circuit Breakers (250%): Standard molded-case circuit breakers containing a thermal bimetal element (which deflects slowly during moderate overloads) and a magnetic armature (which trips instantaneously on high fault currents). Because inverse-time breakers trip faster on higher currents, the 250% multiplier ensures the magnetic trip threshold clears motor starting inrush without tripping.

Dual-Element (Time-Delay) Fuses (175%): These fuses contain two distinct internal elements: a spring-loaded solder pot that melts on prolonged overloads, and a silver or copper fusible link that vaporizes in milliseconds on short circuits. Because the dual-element design provides a built-in 10-second thermal delay at 500% load, the NEC allows a lower multiplier of 175% , providing tighter short-circuit and arc-flash protection.

Nontime-Delay Fuses (300%): Fuses that contain only a single fast-acting zinc or copper element without built-in thermal time delay. To prevent nuisance blowing during the 600% motor start, the fuse must be sized at 300% of full-load current.

Instantaneous Trip Circuit Breakers (800%): Magnetic-only circuit breakers that have no thermal overload trip mechanism whatsoever. They respond purely to instantaneous electromagnetic flux.

The Sizing Rules: Exception No. 1 vs. Exception No. 2

Calculating the maximum permissible SCGF device requires navigating the two core exceptions of NEC Section 430.52(C)(1) :

Exception No. 1: Rounding UP to the Next Standard Rating

Under NEC 430.52(C)(1) Exception No. 1 , where the values for branch-circuit short-circuit and ground-fault protective devices determined by Table 430.52 do not correspond to the standard ampere ratings of fuses or nonadjustable circuit breakers listed in NEC 240.6(A) , the next higher standard ampere rating shall be permitted .

Standard Ampere Ratings (NEC 240.6(A)): \text{Standard Ampere Ratings (NEC 240.6(A)):} Standard Ampere Ratings (NEC 240.6(A)): 10 , 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 60 , 70 , 80 , 90 , 100 , 110 , 125 , 150 , 175 , 200 , 225 , 250 , 300 , 350 , 400 , 450 , 500 , 600 , 700 , 800 , 1000 , 1200 10, 15, 20, 25, 30, 35, 40, 45, 50, 60, 70, 80, 90, 100, 110, 125, 150, 175, 200, 225, 250, 300, 350, 400, 450, 500, 600, 700, 800, 1000, 1200 10 , 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 60 , 70 , 80 , 90 , 100 , 110 , 125 , 150 , 175 , 200 , 225 , 250 , 300 , 350 , 400 , 450 , 500 , 600 , 700 , 800 , 1000 , 1200

Exam Rule: If a calculation yields 85.0 A 85.0\text{ A} 85.0 A for an inverse-time circuit breaker, 85A is not listed in NEC 240.6(A). Under Exception No. 1, you round UP to 90 A 90\text{ A} 90 A .

Exception No. 2: Starting Failure & Absolute Maximum Device Caps

What happens if an inverse-time breaker or dual-element fuse sized under Exception No. 1 trips when the motor attempts to start? Under NEC 430.52(C)(1) Exception No. 2 , where the rating specified in Table 430.52 is not sufficient for the starting current of the motor, the device rating is permitted to be increased up to the following absolute maximum limits :

Dual-Element (Time-Delay) Fuse: May be increased to not exceed 225 % 225\% 225% of motor full-load current.

Nontime-Delay Fuse (600A or less): May be increased to not exceed 400 % 400\% 400% of motor full-load current.

Inverse-Time Circuit Breaker:

If motor full-load current is 100 A 100\text{ A} 100 A or less : may be increased to not exceed 400 % 400\% 400% .

If motor full-load current is greater than 100 A 100\text{ A} 100 A : may be increased to not exceed 300 % 300\% 300% .

Critical Distinction: You cannot automatically jump to Exception No. 2 on an exam unless the question explicitly states that the device sized under Table 430.52 "is not sufficient to start the motor" or "nuisance-trips upon starting." Standard design always proceeds under Table 430.52 and Exception No. 1.

Note

The 2026 NEC adds BE (brushless excitation) and CE (capacitor excitation) motors throughout Article 430. These energy-efficient designs typically have higher locked-rotor currents, so check the 2026 Table 430.52 row for the motor type before applying a percentage.

Instantaneous Trip Circuit Breakers & MCPs (NEC 430.52(C)(3))

An instantaneous trip circuit breaker (commonly termed a Motor Circuit Protector or MCP ) has an adjustable magnetic trip dial with no thermal overload unit. Because an MCP has no thermal element, if an installer wired an MCP to directly feed a motor without overload relays, a mechanical overload or stalled rotor would cause the conductors and motor to incinerate without tripping the breaker!

To prevent catastrophic fires, NEC 430.52(C)(3) establishes strict statutory conditions for MCPs:

Listed Combination Assembly: An instantaneous trip circuit breaker is permitted only as part of a listed combination motor controller that incorporates coordinated overload protection in the same assembly.

Maximum Initial Setting: The magnetic trip setting shall not exceed 800 % 800\% 800% of motor Table FLC (or 1100 % 1100\% 1100% for Design B energy-efficient motors).

Starting Surge Exception: Where the setting specified in Table 430.52 is not sufficient for the starting current of the motor, the setting may be increased over 800 % 800\% 800% , but shall in no case exceed 1300 % 1300\% 1300% of motor full-load current for standard motors, or 1700 % 1700\% 1700% for Design B energy-efficient motors (NEC 430.52(C)(3) Exception No. 1).

  • Step-by-Step Worked SCGF Protection Calculations
  • Example 1: 3-Phase Motor Protected by Dual-Element Fuses

A continuous-duty 10 HP, 208-volt, 3-phase squirrel-cage induction motor is to be protected by dual-element time-delay fuses. What is the maximum standard rating of fuses permitted for branch-circuit short-circuit and ground-fault protection?

Step 1: Find Table FLC

From NEC Table 430.250, a 10 HP, 208V, 3-phase motor has a full-load current of 30.8 A 30.8\text{ A} 30.8 A .

Step 2: Identify Table 430.52 Multiplier

For a squirrel-cage motor protected by dual-element (time-delay) fuses, the multiplier is 175 % 175\% 175% ( 1.75 1.75 1.75 ).

Step 3: Calculate Maximum Protective Rating

Maximum Fuse Rating = 30.8 A × 1.75 = 53.9 A \text{Maximum Fuse Rating} = 30.8\text{ A} \times 1.75 = 53.9\text{ A} Maximum Fuse Rating = 30.8 A × 1.75 = 53.9 A

Step 4: Apply Exception No. 1 (Round UP to Standard Size)

Review standard ratings in NEC 240.6(A): 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 60 , 70 A 15, 20, 25, 30, 35, 40, 45, 50, 60, 70\text{ A} 15 , 20 , 25 , 30 , 35 , 40 , 45 , 50 , 60 , 70 A .

Because 53.9 A 53.9\text{ A} 53.9 A is not a standard rating, Exception No. 1 allows the next higher standard rating: Permitted Standard Dual-Element Fuse = 60 A \text{Permitted Standard Dual-Element Fuse} = \mathbf{60\text{ A}} Permitted Standard Dual-Element Fuse = 60 A

Example 2: 3-Phase Motor Protected by Inverse-Time Circuit Breaker

A continuous-duty 25 HP, 460-volt, 3-phase squirrel-cage motor (Design B) has a Table 430.250 full-load current of 34 A 34\text{ A} 34 A . An inverse-time circuit breaker is selected for branch-circuit SCGF protection. What is the maximum standard breaker rating permitted?

Step 1: Table FLC & Multiplier

Table FLC = 34 A 34\text{ A} 34 A .

Table 430.52 multiplier for inverse-time circuit breaker = 250 % 250\% 250% ( 2.50 2.50 2.50 ).

Step 2: Calculate Rating

Maximum Breaker Setting = 34 A × 2.50 = 85.0 A \text{Maximum Breaker Setting} = 34\text{ A} \times 2.50 = 85.0\text{ A} Maximum Breaker Setting = 34 A × 2.50 = 85.0 A

Step 3: Apply Exception No. 1 (Next Higher Standard Size)

Standard ratings in NEC 240.6(A) near 85A are 70 , 80 , 90 , 100 A 70, 80, 90, 100\text{ A} 70 , 80 , 90 , 100 A .

Sizing at 80A would be less than 85A. Under Exception No. 1, rounding up to the next higher standard size is permitted: Permitted Standard Inverse-Time Breaker = 90 A \text{Permitted Standard Inverse-Time Breaker} = \mathbf{90\text{ A}} Permitted Standard Inverse-Time Breaker = 90 A

Example 3: Single-Phase Motor with Nontime-Delay Fuses

A 7.5 HP, 230-volt single-phase motor has a Table 430.248 full-load current of 40 A 40\text{ A} 40 A . Nontime-delay fuses are installed. What is the maximum standard fuse rating permitted under Table 430.52 and Section 430.52(C)(1) Exception No. 1?

Step 1: Table FLC & Multiplier

Table FLC = 40 A 40\text{ A} 40 A .

Table 430.52 multiplier for nontime-delay fuse = 300 % 300\% 300% ( 3.00 3.00 3.00 ).

Step 2: Calculate Maximum Fuse Rating

Maximum Fuse Rating = 40 A × 3.00 = 120.0 A \text{Maximum Fuse Rating} = 40\text{ A} \times 3.00 = 120.0\text{ A} Maximum Fuse Rating = 40 A × 3.00 = 120.0 A

Step 3: Select Standard Size (NEC 240.6(A))

Standard ratings near 120A are 100 , 110 , 125 , 150 A 100, 110, 125, 150\text{ A} 100 , 110 , 125 , 150 A .

Since 120A is non-standard, Exception No. 1 permits rounding up to 125 A 125\text{ A} 125 A : Permitted Standard Nontime-Delay Fuse = 125 A \text{Permitted Standard Nontime-Delay Fuse} = \mathbf{125\text{ A}} Permitted Standard Nontime-Delay Fuse = 125 A

Example 4: Motor Starting Failure Escalation (Exception No. 2)

Suppose the 25 HP motor in Example 2 ( I FLC = 34 A I_{\text{FLC}} = 34\text{ A} I FLC ​ = 34 A ) drives a heavy industrial rock crusher. When energized, the 90A inverse-time breaker trips due to high mechanical inertia during acceleration. What is the absolute maximum inverse-time circuit breaker rating that can be installed under NEC 430.52(C)(1) Exception No. 2?

Because the motor full-load current is 34 A 34\text{ A} 34 A (which is ≤ 100 A \le 100\text{ A} ≤ 100 A ), Exception No. 2(c) permits increasing the rating up to 400 % 400\% 400% : Absolute Maximum Breaker = 34 A × 4.00 = 136.0 A \text{Absolute Maximum Breaker} = 34\text{ A} \times 4.00 = 136.0\text{ A} Absolute Maximum Breaker = 34 A × 4.00 = 136.0 A

Under Exception No. 2, the rating shall not exceed 400%. The largest standard rating that does not exceed 136 A 136\text{ A} 136 A is 125 A 125\text{ A} 125 A (or 150 A 150\text{ A} 150 A if interpreted with next-size rules under local inspection policy; however, 400% represents a hard statutory cap).

Several Motors on One Branch Circuit (NEC 430.53)

Two or more motors may share one branch circuit only under one of these conditions, and each motor still needs its own overload protection:

Condition Rule

Small motors (430.53(A)) Several motors, each not over 1 hp , on a nominal 120 V branch circuit protected at not over 20 A , or a branch circuit of 1000 V or less protected at not over 15 A, where each motor's full-load rating is not over 6 A and the SCGF rating marked on any controller is not exceeded

Smallest motor protected (430.53(B)) The branch-circuit SCGF device does not exceed the value 430.52 allows for the smallest motor, and it will not open under the most severe normal operating conditions

Group installation (430.53(C)) Motor controllers and overload devices are listed for group installation , or installed as a listed factory assembly, and the branch-circuit fuses or inverse-time breakers do not exceed the marked maximum ratings

Example: three ½ hp, 115 V fan motors each have a full-load current of 9.8 A in Table 430.248. They cannot use the small-motor rule of 430.53(A), because 9.8 A exceeds 6 A. They need individual branch circuits, a branch-circuit device sized for the smallest motor under 430.53(B), or listed group-installation components.

  • Practical Exam Scenarios & Trap Avoidance
  • Trap 1: Rounding Down on Motor Branch Circuits

Exam Trap: A student calculates 30.8 A × 1.75 = 53.9 A 30.8\text{ A} \times 1.75 = 53.9\text{ A} 30.8 A × 1.75 = 53.9 A and rounds down to a 50A fuse, assuming normal overcurrent rules apply.

Correction: Under NEC 430.52(C)(1) Exception No. 1 , motor branch circuits explicitly allow rounding UP to the next higher standard rating (60A in this case). Note that this is the exact opposite of feeder overcurrent protection under 430.62, which mandates rounding down !

Trap 2: Using the 125% Conductor Multiplier for Overcurrent Sizing

Exam Trap: Multiplying the conductor ampacity ( 1.25 × I FLC 1.25 \times I_{\text{FLC}} 1.25 × I FLC ​ ) by the Table 430.52 percentage.

Correction: Table 430.52 percentages apply directly to the unmultiplied Table FLC , not to the 125% conductor ampacity. For example, for an inverse-time breaker, calculate I table × 2.50 I_{\text{table}} \times 2.50 I table ​ × 2.50 , NOT ( I table × 1.25 ) × 2.50 (I_{\text{table}} \times 1.25) \times 2.50 ( I table ​ × 1.25 ) × 2.50 .

Trap 3: Confusing Fuse Multipliers (Dual Element vs. Nontime Delay)

Exam Trap: Using 300% for a dual-element fuse or 175% for a nontime-delay fuse.

Correction: Remember that dual-element fuses have time delay , so they require only 175% . Nontime-delay fuses blow instantly , so they require a massive 300% window to survive motor starting.