Study guide

15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI)

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI)

Key Takeaways Explain This Topic AI

A motor disconnecting means must be within sight of the motor and its driven machinery, unless the controller disconnect is lockable in the open position and a disconnect at the motor is impracticable or the site is an industrial establishment with written safety procedures (430.102(B)).

Motor disconnecting means must have an ampere rating of at least 115% of the motor's full-load current for motors rated 1000 V or less (430.110(A)).

For a stationary motor of 2 hp or less at 300 V or less, a general-use switch rated at least twice the motor full-load current may serve as the disconnecting means (430.109(C)(2)).

Conductors supplying adjustable-speed drive equipment must have an ampacity of at least 125% of the drive's rated input current (430.122(A)).

The 2026 NEC 430.98(A) requires a motor control center supplied by a feeder to be marked with the location of the means to disconnect all power to it.

Last updated: October 2026

Motor controllers (Article 430, Part VII)

A controller is any switch or device used to start and stop a motor by making and breaking the motor circuit current. It may be a magnetic starter, manual motor starter, drive, or, for small motors, a switch or breaker.

Rule Requirement

Rating (430.83(A)) Horsepower rating at the application voltage not lower than the motor's; a circuit breaker rated in amperes may also serve as a controller

Small motors (430.83(C)) For stationary motors of 2 hp or less at 300 V or less : a general-use switch rated at least twice the motor full-load current, or an AC general-use snap switch where the motor full-load current does not exceed 80% of the switch rating

Voltage (430.83(E)) Slash-rated controllers (for example 480Y/277 V) only on solidly grounded systems within both values

Conductors opened (430.84) A controller need not open all conductors to the motor, unless it also serves as the disconnecting means

One controller per motor (430.87) Each motor needs its own controller, with limited exceptions for groups of motors at 1000 V or less driving parts of a single machine, or in a single room within sight of the controller

  • Disconnecting means (Article 430, Part IX)
  • Location (430.102)

Controller disconnect (A): an individual disconnecting means must be provided ahead of each controller and within sight from the controller location.

Motor disconnect (B): a disconnecting means must also be located within sight from the motor location and the driven machinery . The controller disconnect may serve as the motor disconnect if it is within sight of the motor.

Exception: the motor disconnect is not required if the controller disconnect is lockable in the open position (110.25) and either a disconnect at the motor is impracticable or would introduce additional or increased hazards , or the installation is in an industrial establishment with written safety procedures where only qualified persons service the equipment.

"Within sight" means visible and not more than 50 ft away (110.29).

Operation and accessibility (430.103 to 430.107)

The disconnecting means must open all ungrounded supply conductors simultaneously and be designed so it cannot close automatically.

It must plainly indicate whether it is open (off) or closed (on) .

At least one of the disconnecting means must be readily accessible .

Type (430.109)

Permitted types include a listed motor-circuit switch rated in horsepower, a listed molded-case circuit breaker , a listed molded-case switch , an instantaneous-trip circuit breaker that is part of a listed combination motor controller, a listed self-protected combination motor controller , a listed manual motor controller marked "Suitable as Motor Disconnect" (on the load side of the final branch-circuit short-circuit protective device), and listed system isolation equipment. Special cases:

  • Motor Permitted disconnecting means
  • Stationary, ⅛ hp or less The branch-circuit OCPD

Stationary, 2 hp or less, 300 V or less A general-use switch rated at least twice the full-load current, or an AC general-use snap switch where the full-load current is not more than 80% of its rating

Cord-and-plug connected A horsepower-rated attachment plug and receptacle, or for portable motors of ⅓ hp or less, an attachment plug and receptacle

Rating (430.110)

For motors of 1000 V or less, the disconnecting means must have an ampere rating of at least 115% of the motor's Table full-load current. Where a disconnect serves several motors or other loads, its rating is found by adding the full-load currents and the locked-rotor currents of all loads and converting to an equivalent horsepower using Table 430.251(A) or (B) .

Example: a 25 hp, 460 V, three-phase motor has a Table 430.250 full-load current of 34 A. The disconnect must be rated at least 34 × 1.15 = 39.1 34 \times 1.15 = 39.1 34 × 1.15 = 39.1 A and at least 25 hp at 460 V, so a 60 A, 25 hp or larger switch is typical.

Control circuits (Article 430, Part VI)

Overcurrent protection (430.72): motor control circuit conductors tapped from the branch circuit need protection sized from Table 430.72(B); control transformers need protection under 430.72(C).

Arrangement (430.74): an accidental ground in the control circuit must not start the motor or bypass shutdown devices.

Disconnection (430.75): control circuits must be disconnected from all sources by the disconnecting means; where a control transformer is in the controller enclosure, it must be on the load side of the disconnect.

Adjustable-speed drives (Article 430, Part X)

  • Rule Requirement
  • Conductors (430.122(A)) Ampacity at least 125% of the rated input current of the power conversion equipment

Bypass device (430.122(B)) Where a bypass is provided, conductors are sized for the larger of 125% of the drive input current or 125% of the motor full-load current

Overload protection (430.124) Provided by the drive if it is marked as providing it; otherwise separate overload protection is required

Disconnecting means (430.128) Permitted in the incoming line to the conversion equipment, rated at least 115% of its rated input current

Motor control centers (Article 430, Part VIII)

Motor control centers must be protected under Article 240, meet working space rules, and be marked with their ratings. The 2026 NEC 430.98(A) requires an MCC supplied by a feeder to be marked with the location of the means to disconnect all power to the MCC, so a worker can find the upstream disconnect quickly.

Worked example: a rooftop exhaust fan

A 3 hp, 208 V, three-phase exhaust fan on a roof is controlled by a starter in an electrical room two floors below.

Table FLC: Table 430.250 gives 10.6 A for 3 hp at 208 V.

Controller disconnect: within sight of the starter in the electrical room.

Motor disconnect: the electrical room is not within sight of the fan, so a disconnect is needed at the fan, unless the controller disconnect is lockable and the conditions of the exception apply. A disconnect at a rooftop fan is practical, so install one.

Rating: at least 10.6 × 1.15 = 12.2 10.6 \times 1.15 = 12.2 10.6 × 1.15 = 12.2 A, and horsepower rated for 3 hp at 208 V, such as a 30 A, 3-pole horsepower-rated switch.