Study guide

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22)

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22)

Key Takeaways Explain This Topic AI

Under NEC 430.6(A)(1), motor branch-circuit conductor ampacity, disconnect ratings, and short-circuit/ground-fault protective device ratings must be calculated using the Table Full-Load Current (FLC) values from NEC Tables 430.247 through 430.250, never the motor nameplate current.

The motor nameplate full-load current rating is reserved strictly for sizing separate motor overload protective devices (such as thermal overload relays or heater coils) under NEC 430.6(A)(1) and NEC 430.32.

Under NEC 430.22, branch-circuit conductors supplying a single continuous-duty motor must have an allowable ampacity of not less than 125 percent of the motor table FLC rating ( I conductor ≥ 1.25 × I table I_{\text{conductor}} \ge 1.25 \times I_{\text{table}} I conductor ​ ≥ 1.25 × I table ​ ).

Conductor selection must evaluate terminal temperature ratings under NEC 110.14(C); equipment rated 100 A or less uses the 60°C column of Table 310.16 unless marked for 75°C, while equipment rated over 100 A uses the 75°C column.

For motors operating on non-continuous duty or specialized duty cycles (short-time, intermittent, periodic, or varying duty), conductor ampacity percentages are determined using NEC Table 430.22(E), ranging from 85% up to 200% of motor nameplate current.

Last updated: October 2026

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22)

Quick Answer: Under NEC 430.6(A)(1) , motor branch-circuit conductors, disconnect switches, and short-circuit protective devices must be sized using Table Full-Load Current (FLC) from NEC Tables 430.247 through 430.250 , rather than the motor's actual nameplate rating. The nameplate current is used only for sizing separate motor overload devices under NEC 430.32 . Under NEC 430.22 , conductors supplying a single continuous-duty motor must have an allowable ampacity of not less than 125 percent of the motor table FLC ( I conductor ≥ 1.25 × I table I_{\text{conductor}} \ge 1.25 \times I_{\text{table}} I conductor ​ ≥ 1.25 × I table ​ ).

Electric motors represent inductive, dynamic loads that behave fundamentally differently from resistive heating or general lighting circuits. When energized across the line, an AC induction motor draws an instantaneous inrush or locked-rotor current typically equal to 400% to 800% of its normal operating current . Furthermore, mechanical loading varies continuously, motors generate internal heat that must dissipate through their enclosures, and motors may stall or cycle repeatedly. Consequently, NEC Article 430 contains specialized, standalone engineering rules that override the general wiring and overcurrent protection requirements found in Articles 210 and 240.

For Minnesota journeyworker candidates, mastering Article 430 calculations is essential. The licensing examination regularly presents multi-step calculation problems requiring candidates to navigate Table FLC lookups, apply the 125% continuous sizing factor, evaluate conductor ampacity under NEC Table 310.16 , verify terminal temperature ratings under NEC 110.14(C) , and apply ambient temperature and raceway fill adjustments.

Structure & Map of NEC Article 430

Article 430 is one of the longest and most structured articles in the National Electrical Code. To assist electricians in navigating its rules, NEC Figure 430.1 establishes an architectural roadmap dividing motor circuits into distinct functional segments:

Unlike general branch circuits—where a single fuse or circuit breaker simultaneously protects conductors against both sustained overloads and high-magnitude short circuits—a motor branch circuit separates these two protective duties:

Overload Protection (Part III): Protects the motor windings, controller, and branch conductors from moderate, sustained overheating caused by motor mechanical overloads or failure to start.

Branch-Circuit Short-Circuit and Ground-Fault (SCGF) Protection (Part IV): Protects the circuit conductors and equipment against catastrophic, high-magnitude fault currents resulting from phase-to-phase short circuits or ground faults.

The Golden Rule of Motor Current: Table FLC vs. Nameplate (NEC 430.6(A)(1))

The single most critical rule in all motor circuit design is established in NEC Section 430.6(A)(1) : Table FLC (Tables 430.247–430.250) ⟹ Conductor Sizing, Disconnects, SCGF Protection Nameplate Current ⟹ Separate Motor Overload Protection Only \begin{aligned}

  • \textbf{Table FLC (Tables 430.247–430.250)} &\implies \text{Conductor Sizing, Disconnects, SCGF Protection} \\
  • \textbf{Nameplate Current} &\implies \text{Separate Motor Overload Protection Only}

\end{aligned} Table FLC (Tables 430.247–430.250) Nameplate Current ​ ⟹ Conductor Sizing, Disconnects, SCGF Protection ⟹ Separate Motor Overload Protection Only ​

Why Does the Code Mandate Table FLC for Conductor & Short-Circuit Sizing?

Motor nameplates reflect the specific operating current of that individual manufactured motor. However, if a motor fails in service, maintenance personnel frequently replace it with a motor of identical horsepower and speed rating from a different manufacturer. If the original branch circuit conductors, raceways, and protective devices were sized to a uniquely low nameplate current, the replacement motor could overheat the wiring or nuisance-trip the breaker. Standard table values represent conservative, industry-wide worst-case full-load currents for motors of standard horsepower, speed, and voltage ratings.

The Four NEC Motor Current Tables

Electricians must select the appropriate table based on the system electrical characteristics:

NEC Table 430.247: Full-Load Current in Amperes for Direct-Current (DC) Motors .

NEC Table 430.248: Full-Load Current in Amperes for Single-Phase Alternating-Current Motors (operating at 115V, 200V, 208V, 230V).

NEC Table 430.249: Full-Load Current in Amperes for Two-Phase AC Motors (4-wire).

NEC Table 430.250: Full-Load Current in Amperes for Three-Phase AC Induction & Synchronous Motors (operating at 115V, 200V, 208V, 230V, 460V, 575V, 2300V).

Voltage Adjustments and Footnotes

When motor voltages vary from standard table headings, the footnotes of Tables 430.248 and 430.250 govern:

For motors operating at 200 volts , take the current listed under the 230-volt column and increase it by 15 percent ( I 200 V = I 230 V × 1.15 I_{200\text{V}} = I_{230\text{V}} \times 1.15 I 200 V ​ = I 230 V ​ × 1.15 ), or use the designated 200V column if provided.

For motors rated at 208 volts , use the explicit 208-volt column in Table 430.250 (which reflects approximately a 10% increase over 230V values).

Motor Horsepower (HP) 3-Phase 208V FLC (A) 3-Phase 230V FLC (A) 3-Phase 460V FLC (A) 1-Phase 115V FLC (A) 1-Phase 230V FLC (A)

  • 1/2 HP — — — 9.8 A 9.8\text{ A} 9.8 A 4.9 A 4.9\text{ A} 4.9 A
  • 3/4 HP — — — 13.8 A 13.8\text{ A} 13.8 A 6.9 A 6.9\text{ A} 6.9 A

1 HP 4.6 A 4.6\text{ A} 4.6 A 4.2 A 4.2\text{ A} 4.2 A 2.1 A 2.1\text{ A} 2.1 A 16.0 A 16.0\text{ A} 16.0 A 8.0 A 8.0\text{ A} 8.0 A

1.5 HP 6.6 A 6.6\text{ A} 6.6 A 6.0 A 6.0\text{ A} 6.0 A 3.0 A 3.0\text{ A} 3.0 A 20.0 A 20.0\text{ A} 20.0 A 10.0 A 10.0\text{ A} 10.0 A

2 HP 7.5 A 7.5\text{ A} 7.5 A 6.8 A 6.8\text{ A} 6.8 A 3.4 A 3.4\text{ A} 3.4 A 24.0 A 24.0\text{ A} 24.0 A 12.0 A 12.0\text{ A} 12.0 A

3 HP 10.6 A 10.6\text{ A} 10.6 A 9.6 A 9.6\text{ A} 9.6 A 4.8 A 4.8\text{ A} 4.8 A 34.0 A 34.0\text{ A} 34.0 A 17.0 A 17.0\text{ A} 17.0 A

5 HP 16.7 A 16.7\text{ A} 16.7 A 15.2 A 15.2\text{ A} 15.2 A 7.6 A 7.6\text{ A} 7.6 A 56.0 A 56.0\text{ A} 56.0 A 28.0 A 28.0\text{ A} 28.0 A

7.5 HP 24.2 A 24.2\text{ A} 24.2 A 22.0 A 22.0\text{ A} 22.0 A 11.0 A 11.0\text{ A} 11.0 A 80.0 A 80.0\text{ A} 80.0 A 40.0 A 40.0\text{ A} 40.0 A

10 HP 30.8 A 30.8\text{ A} 30.8 A 28.0 A 28.0\text{ A} 28.0 A 14.0 A 14.0\text{ A} 14.0 A 100.0 A 100.0\text{ A} 100.0 A 50.0 A 50.0\text{ A} 50.0 A

  • 15 HP 46.2 A 46.2\text{ A} 46.2 A 42.0 A 42.0\text{ A} 42.0 A 21.0 A 21.0\text{ A} 21.0 A — —
  • 20 HP 59.4 A 59.4\text{ A} 59.4 A 54.0 A 54.0\text{ A} 54.0 A 27.0 A 27.0\text{ A} 27.0 A — —
  • 25 HP 74.8 A 74.8\text{ A} 74.8 A 68.0 A 68.0\text{ A} 68.0 A 34.0 A 34.0\text{ A} 34.0 A — —
  • 30 HP 88.0 A 88.0\text{ A} 88.0 A 80.0 A 80.0\text{ A} 80.0 A 40.0 A 40.0\text{ A} 40.0 A — —
  • 40 HP 114.0 A 114.0\text{ A} 114.0 A 104.0 A 104.0\text{ A} 104.0 A 52.0 A 52.0\text{ A} 52.0 A — —
  • 50 HP 143.0 A 143.0\text{ A} 143.0 A 130.0 A 130.0\text{ A} 130.0 A 65.0 A 65.0\text{ A} 65.0 A — —
  • 75 HP 211.0 A 211.0\text{ A} 211.0 A 192.0 A 192.0\text{ A} 192.0 A 96.0 A 96.0\text{ A} 96.0 A — —
  • 100 HP 273.0 A 273.0\text{ A} 273.0 A 248.0 A 248.0\text{ A} 248.0 A 124.0 A 124.0\text{ A} 124.0 A — —
  • Single Motor Branch-Circuit Conductor Sizing (NEC 430.22)

Under NEC 430.22 , conductors that supply a single motor used in a continuous-duty application shall have an ampacity of not less than 125 percent of the motor full-load current rating as determined by Section 430.6(A)(1):

I conductor minimum = I table FLC × 1.25 I_{\text{conductor minimum}} = I_{\text{table FLC}} \times 1.25 I conductor minimum ​ = I table FLC ​ × 1.25

Why 125 Percent?

Continuous-duty motors generate internal losses that conduct through their frame into terminal connection boxes. Operating at full load continuously induces thermal accumulation in conductors adjacent to the motor housing. Sizing conductors at 125% provides thermal margin and ensures conductors do not operate at their absolute thermal limit.

Terminal Temperature Limitations (NEC 110.14(C))

Once the minimum required ampacity ( 1.25 × I table 1.25 \times I_{\text{table}} 1.25 × I table ​ ) is calculated, the conductor size is selected from NEC Table 310.16 . However, the allowable ampacity column depends on the temperature ratings of the terminals:

NEC 110.14(C)(1)(a) (Circuits Rated 100A or Less / 14 AWG through 1 AWG): Unless the motor controller, switch, and motor terminal box are specifically listed and marked for 75 ∘ C 75^\circ\text{C} 7 5 ∘ C , conductors must be sized based on the 60 ∘ C 60^\circ\text{C} 6 0 ∘ C column of Table 310.16.

NEC 110.14(C)(1)(b) (Circuits Rated Over 100A / Conductors Larger than 1 AWG): Permitted to use the 75 ∘ C 75^\circ\text{C} 7 5 ∘ C column of Table 310.16 unless marked otherwise.

Modern Motor Terminals: While nearly all modern conductors installed in commercial work are rated for 90 ∘ C 90^\circ\text{C} 9 0 ∘ C (e.g., THHN/THWN-2, XHHW-2), motor terminals and circuit breakers are almost universally listed for a maximum of 75 ∘ C 75^\circ\text{C} 7 5 ∘ C . Therefore, the 75 ∘ C 75^\circ\text{C} 7 5 ∘ C ampacity serves as the absolute maximum permitted load ampacity for termination purposes.

Exemption from Small Conductor Rules (NEC 240.4(G))

A critical code rule frequently tested on the Minnesota examination is that motor circuits are exempt from the small conductor overcurrent limitations of NEC 240.4(D) . Under NEC 240.4(G) , the overcurrent protection of motor conductors is governed exclusively by Article 430 Parts IV and V. For example, a 14 AWG copper conductor (with an ampacity of 20A at 75°C or 25A at 90°C) is not restricted to a 15A breaker when used in a motor branch circuit; it may be protected by a 30A or 40A inverse-time circuit breaker if authorized under Table 430.52!

Conductor Ampacity Derating for Motors (NEC 310.15)

When motor branch-circuit conductors are installed in environments with elevated ambient temperatures or in raceways containing more than three current-carrying conductors, the ampacity must be adjusted in accordance with NEC 310.15(B)(1) (ambient temperature correction) and NEC 310.15(C)(1) (raceway fill adjustment):

Derated Ampacity = I Table 310.16 (90°C) × C temp × C fill \text{Derated Ampacity} = I_{\text{Table 310.16 (90°C)}} \times C_{\text{temp}} \times C_{\text{fill}} Derated Ampacity = I Table 310.16 (90°C) ​ × C temp ​ × C fill ​

The Two-Step Derating Verification Rule

When working with 90 ∘ C 90^\circ\text{C} 9 0 ∘ C rated conductors (such as THHN) terminated on 75 ∘ C 75^\circ\text{C} 7 5 ∘ C terminals:

Step 1 (Raceway / Ambient Derating): Multiply the 90 ∘ C 90^\circ\text{C} 9 0 ∘ C base ampacity from Table 310.16 by the adjustment factors ( C temp C_{\text{temp}} C temp ​ and C fill C_{\text{fill}} C fill ​ ). The resulting derated ampacity must be greater than or equal to 1.25 × I table 1.25 \times I_{\text{table}} 1.25 × I table ​ .

Step 2 (Terminal Rating Check): The continuous motor load ( 1.25 × I table 1.25 \times I_{\text{table}} 1.25 × I table ​ ) must not exceed the allowable ampacity of the selected conductor from the 75 ∘ C 75^\circ\text{C} 7 5 ∘ C column of Table 310.16.

Duty Cycle Classifications Other Than Continuous (NEC Table 430.22(E))

Not all motors operate continuously. Applications such as overhead crane hoists, freight elevators, valve actuators, and drawbridges operate intermittently or for very short durations. Under NEC 430.22(E) , where a motor is used in other than continuous duty, the conductor ampacity shall not be less than the percentage of motor nameplate current specified in NEC Table 430.22(E) :

Classification of Service 5-Minute Rated Motor 15-Minute Rated Motor 30- & 60-Minute Rated Continuous Rated Motor

Short-Time Duty (Operating valves, roll-up doors, hoists) 110 % 110\% 110% 120 % 120\% 120% 150 % 150\% 150% —

Intermittent Duty (Freight elevators, tool heads, pumps) 85 % 85\% 85% 85 % 85\% 85% 90 % 90\% 90% 140 % 140\% 140%

Periodic Duty (Rolls, ore- and coal-handling equipment) 85 % 85\% 85% 90 % 90\% 90% 95 % 95\% 95% 140 % 140\% 140%

Varying Duty (Loads varying substantially under process) 110 % 110\% 110% 120 % 120\% 120% 150 % 150\% 150% 200 % 200\% 200%

Exam Tip: Notice that for non-continuous duty cycles under Table 430.22(E), calculations use the motor nameplate current rating , because the duty-cycle ratings are certified on the manufacturer's nameplate rather than standardized tables.

  • Step-by-Step Worked Conductor Sizing Calculations
  • Example 1: Standard 3-Phase 460V Industrial Motor

A continuous-duty, 3-phase, 460-volt, 25 HP squirrel-cage induction motor with Design B characteristics is installed in a manufacturing plant. The motor nameplate lists a full-load current of 31 A 31\text{ A} 31 A , a service factor of 1.15 1.15 1.15 , and a temperature rise of 40 ∘ C 40^\circ\text{C} 4 0 ∘ C . The branch circuit will be wired with THHN copper conductors in EMT conduit to terminals rated for 75 ∘ C 75^\circ\text{C} 7 5 ∘ C . The ambient temperature is 30 ∘ C 30^\circ\text{C} 3 0 ∘ C ( 86 ∘ F 86^\circ\text{F} 8 6 ∘ F ).

Step 1: Determine Governing Full-Load Current

Under NEC 430.6(A)(1) , branch-circuit conductor sizing must use the value from NEC Table 430.250 , NOT the nameplate rating ( 31 A 31\text{ A} 31 A ).

Locate 25 HP under the 460V column in Table 430.250: I table FLC = 34 A I_{\text{table FLC}} = 34\text{ A} I table FLC ​ = 34 A

Step 2: Apply the 125% Continuous Duty Sizing Factor (NEC 430.22)

I conductor minimum = 34 A × 1.25 = 42.5 A I_{\text{conductor minimum}} = 34\text{ A} \times 1.25 = \mathbf{42.5\text{ A}} I conductor minimum ​ = 34 A × 1.25 = 42.5 A

Step 3: Select Conductor Size from NEC Table 310.16

Terminal rating is 75 ∘ C 75^\circ\text{C} 7 5 ∘ C . Review the 75 ∘ C 75^\circ\text{C} 7 5 ∘ C copper column of Table 310.16:

10 AWG copper has an ampacity of 35 A 35\text{ A} 35 A ( 35 A < 42.5 A 35\text{ A} < 42.5\text{ A} 35 A < 42.5 A — insufficient).

8 AWG copper has an ampacity of 50 A 50\text{ A} 50 A ( 50 A ≥ 42.5 A 50\text{ A} \ge 42.5\text{ A} 50 A ≥ 42.5 A — acceptable).

Conclusion: Sizing requires 8 AWG THHN copper conductors.

Example 2: Commercial Single-Phase 115V Motor

A commercial exhaust fan is powered by a continuous-duty, 1.5 HP, 115-volt single-phase motor. The motor nameplate indicates 18.2 A 18.2\text{ A} 18.2 A . The terminals are marked for 75 ∘ C 75^\circ\text{C} 7 5 ∘ C . What is the minimum required conductor ampacity and the smallest copper THHN conductor permitted?

Step 1: Determine Governing Full-Load Current

Under NEC 430.6(A)(1) , use NEC Table 430.248 for single-phase AC motors.

Locate 1.5 HP at 115V in Table 430.248: I table FLC = 20.0 A I_{\text{table FLC}} = 20.0\text{ A} I table FLC ​ = 20.0 A

Step 2: Calculate Minimum Conductor Ampacity

I conductor minimum = 20.0 A × 1.25 = 25.0 A I_{\text{conductor minimum}} = 20.0\text{ A} \times 1.25 = \mathbf{25.0\text{ A}} I conductor minimum ​ = 20.0 A × 1.25 = 25.0 A

Step 3: Select Conductor Size from NEC Table 310.16

Review Table 310.16 ( 75 ∘ C 75^\circ\text{C} 7 5 ∘ C copper):

14 AWG copper = 20 A 20\text{ A} 20 A (insufficient).

12 AWG copper = 25 A 25\text{ A} 25 A ( 25 A ≥ 25.0 A 25\text{ A} \ge 25.0\text{ A} 25 A ≥ 25.0 A — acceptable).

Conclusion: The branch circuit requires 12 AWG THHN copper conductors.

Example 3: 3-Phase Motor with Elevated Ambient Temperature & Bundling

A continuous-duty 50 HP, 208-volt, 3-phase induction motor is installed in a boiler room with an ambient temperature of 42 ∘ C 42^\circ\text{C} 4 2 ∘ C ( 108 ∘ F 108^\circ\text{F} 10 8 ∘ F ). The raceway contains six current-carrying THHN copper conductors. Equipment terminals are rated for 75 ∘ C 75^\circ\text{C} 7 5 ∘ C . What is the minimum size THHN copper conductor required?

Step 1: Table FLC and Base Sizing

From NEC Table 430.250, a 50 HP motor at 208V has a full-load current of 143 A 143\text{ A} 143 A .

Minimum conductor ampacity under NEC 430.22: I min = 143 A × 1.25 = 178.75 A I_{\text{min}} = 143\text{ A} \times 1.25 = \mathbf{178.75\text{ A}} I min ​ = 143 A × 1.25 = 178.75 A

Step 2: Determine Derating Correction Factors

Ambient Temperature Correction ( 42 ∘ C 42^\circ\text{C} 4 2 ∘ C ): From Table 310.15(B)(1) ( 90 ∘ C 90^\circ\text{C} 9 0 ∘ C column), the factor is 0.87 0.87 0.87 .

Raceway Fill Adjustment (6 conductors): From Table 310.15(C)(1) (4–6 conductors), the factor is 0.80 0.80 0.80 (80%).

Combined derating multiplier: 0.87 × 0.80 = 0.696 0.87 \times 0.80 = 0.696 0.87 × 0.80 = 0.696 .

Step 3: Conductor Evaluation

The conductor derated ampacity must satisfy: Base Ampacity (90°C) × 0.696 ≥ 178.75 A \text{Base Ampacity (90°C)} \times 0.696 \ge 178.75\text{ A} Base Ampacity (90°C) × 0.696 ≥ 178.75 A .

Minimum required 90 ∘ C 90^\circ\text{C} 9 0 ∘ C base ampacity: Base Ampacity ≥ 178.75 A 0.696 = 256.8 A \text{Base Ampacity} \ge \frac{178.75\text{ A}}{0.696} = 256.8\text{ A} Base Ampacity ≥ 0.696 178.75 A ​ = 256.8 A

Check Table 310.16 ( 90 ∘ C 90^\circ\text{C} 9 0 ∘ C copper column):

4/0 AWG copper has a 90 ∘ C 90^\circ\text{C} 9 0 ∘ C rating of 260 A 260\text{ A} 260 A . Derated ampacity: 260 × 0.696 = 180.96 A ≥ 178.75 A 260 \times 0.696 = 180.96\text{ A} \ge 178.75\text{ A} 260 × 0.696 = 180.96 A ≥ 178.75 A (acceptable).

Check 75 ∘ C 75^\circ\text{C} 7 5 ∘ C terminal rating:

4/0 AWG copper in the 75 ∘ C 75^\circ\text{C} 7 5 ∘ C column is rated for 230 A 230\text{ A} 230 A . Because 230 A > 178.75 A 230\text{ A} > 178.75\text{ A} 230 A > 178.75 A , the terminal capacity is fully satisfied.

Conclusion: Sizing requires 4/0 AWG THHN copper conductors.

  • Practical Exam Scenarios & Trap Avoidance
  • Trap 1: Using Nameplate Full-Load Amperes for Conductor Sizing

Exam Trap: A question states: "A 15 HP, 230V, 3-phase motor has a nameplate current of 38A. What is the minimum conductor ampacity?"

Common Error: Calculating 38 A × 1.25 = 47.5 A 38\text{ A} \times 1.25 = 47.5\text{ A} 38 A × 1.25 = 47.5 A .

Correction: Under NEC 430.6(A)(1) , you must ignore the nameplate current for conductor sizing. Look up Table 430.250: 15 HP at 230V is 42 A 42\text{ A} 42 A . Correct calculation: 42 A × 1.25 = 52.5 A 42\text{ A} \times 1.25 = \mathbf{52.5\text{ A}} 42 A × 1.25 = 52.5 A .

Trap 2: Applying NEC 240.4(D) Small Conductor Limits to Motors

Exam Trap: Believing that a 14 AWG copper wire supplying a motor cannot be protected by a breaker larger than 15A.

Correction: Under NEC 240.4(G) , motor branch circuits are governed by Article 430. Table 310.16 ampacities apply without restriction from 240.4(D). A 14 AWG THHN copper conductor can carry up to 20A (at 75°C) or 25A (at 90°C) and be protected by a 30A or 35A breaker under Table 430.52.

Trap 3: Confusing 200V vs. 208V Table Lookups

Exam Trap: Sizing a 208-volt motor using the 230-volt column without adjustment or using the 200-volt footnote.

Correction: In Table 430.250, there is a dedicated 208V column . Always use the exact 208V column rather than mathematical approximations.