Study guide

18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590)

Minnesota Journeyman Electrician Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Minnesota Exam, Licensing & Electrical Law

1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement

2 Electrical Theory, Math & Power Calculations

2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting

3 NEC Structure & General Requirements

3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)

4 Conductors, Identification & Ampacity

4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors

5 Branch Circuits, GFCI/AFCI & Required Outlets

5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)

6 Load Calculations (2026 NEC Article 120)

6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)

7 Feeders, Outside Wiring & Services

7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)

8 Overcurrent Protection

8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction

9 System Grounding & Grounding Electrodes

9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems

10 Bonding & Equipment Grounding

10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding

11 General Wiring Methods & Underground Installations

11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)

12 Raceways, Cables & Conduit Fill

12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)

13 Boxes, Conduit Bodies & Cabinets

13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)

14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances

14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)

15 Motors, Controllers & Air Conditioning

15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)

16 Transformers, Generators & Equipment Over 1000 Volts

16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)

17 Hazardous (Classified) Locations

17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)

18 Health Care, Assembly, Agricultural & Mobile Occupancies

18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)

19 Signs, Elevators, Pools, Solar & Other Specific Equipment

19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)

20 Emergency, Standby & Interconnected Power Sources

20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)

21 Limited-Energy, Fire Alarm & Communications Systems

21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)

18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590)

Key Takeaways Explain This Topic AI

Article 518 applies to buildings or portions of buildings designed or intended for the gathering of 100 or more persons for purposes such as deliberation, worship, entertainment, eating, drinking, or awaiting transportation.

Amusement rides and attractions must be at least 15 ft in any direction from overhead conductors of 600 V or less, except the conductors supplying the ride (Article 525).

Temporary electrical power for holiday decorative lighting is limited to 90 days, and temporary wiring must be removed immediately when construction or the purpose for which it was installed is complete (590.3).

All 125 V, single-phase, 15-, 20-, and 30-ampere receptacle outlets that are not part of the permanent building wiring and are used by personnel during construction must have GFCI protection (590.6(A)).

On construction sites, receptacles may not be installed on branch circuits that supply temporary lighting (590.4(D)).

Last updated: October 2026

Places of assembly (Article 518)

Article 518 covers buildings or portions of buildings designed or intended for 100 or more persons : auditoriums, conference rooms, churches, restaurants, dance halls, gymnasiums, bowling alleys, museums, places of awaiting transportation, and similar. Theaters with stages are covered by Article 520.

Rule Requirement

General wiring methods (518.4(A)) Metal raceways , flexible metal raceways, nonmetallic raceways encased in at least 2 in. of concrete , Type MI , MC , or AC cable containing an insulated EGC sized from Table 250.122

Nonrated construction (518.4(B)) Where the building or portion is not required by the building code to be of fire-rated construction, NM cable, AC cable, ENT, and PVC or RTRC conduit are also permitted

Spaces with finish ratings (518.4(C)) ENT and PVC or RTRC may be installed in concealed spaces of walls, floors, and ceilings behind a thermal barrier with at least a 15-minute finish rating

Temporary wiring (518.3) Temporary wiring for exhibition booths may follow Article 590, with flexible cords and cables approved for hard or extra-hard usage

Portable switchboards and stage equipment Article 520 applies

Minnesota's State Building Code determines whether a portion of a building must be of fire-rated construction, which in turn decides whether NM cable may be used.

Carnivals, circuses, fairs, and similar events (Article 525)

The 2026 NEC restructured and rewrote Article 525 for clarity, separating disconnecting means rules for moving and nonmoving equipment and adding rules for portable and vehicle- or trailer-mounted generators.

Rule Requirement

Overhead conductor clearances Vertical clearances to the public follow 225.18; amusement rides and attractions must be maintained at least 15 ft in any direction from overhead conductors operating at 600 V or less, except the conductors that supply the ride

Services and power sources Service equipment may not be installed in a location accessible to unqualified persons unless lockable; generators and other sources must be protected from public contact

Wiring methods Flexible cords and cables must be listed for extra-hard usage , and where used outdoors, also listed for wet locations and sunlight resistant

Protection Cords and cables accessible to the public must be arranged to minimize tripping and covered with nonconductive matting where run across walkways

Boxes and fittings A box or fitting is required at each connection point, outlet, switch point, or junction

GFCI protection 125 V, single-phase, 15- and 20-ampere nonlocking receptacles used for disassembly and reassembly, or readily accessible to the public, must be GFCI protected; egress lighting may not be GFCI protected

Grounding and bonding All equipment requiring grounding is connected to an EGC; the 2026 NEC adds an exception for portable inverter generators manufactured with no grounded-conductor connection to the frame

  • Temporary installations (Article 590)
  • Time constraints (590.3)
  • Use Time limit
  • Construction, remodeling, maintenance, repair, or demolition For the duration of the work
  • Holiday decorative lighting and similar purposes Not more than 90 days
  • Emergencies and tests For the duration of the emergency or test, such as developmental work

Removal Temporary wiring must be removed immediately upon completion of construction or the purpose for which it was installed

Wiring rules (590.4)

Services must meet Article 230.

Feeders must originate in an approved distribution center, and may use multiconductor cord or cable listed for hard or extra-hard usage .

Branch circuits must originate in an approved power outlet or panelboard, and may use multiconductor cord or cable of the same types. All conductors of a circuit, including the EGC, run together.

Receptacles must be grounding type, electrically connected to an EGC, and on construction sites they may not be installed on branch circuits that supply temporary lighting .

Disconnecting means: suitable disconnecting switches or plug connectors at the distribution center to disconnect all ungrounded conductors of each temporary circuit; multiwire branch circuits need simultaneous disconnection of all ungrounded conductors.

Lamp protection: lamps for general illumination must be protected from accidental contact or breakage by a suitable luminaire or lampholder with a guard.

Splices: on construction sites, a box is not required for splices in multiconductor cord or cable assemblies if equipment grounding continuity is maintained, with or without the box.

Protection and support: cords and cables must be protected from accidental damage, sharp corners, and pinch points, and supported at intervals that protect them. Vegetation may not support overhead spans of branch circuits or feeders, except for holiday lighting with strain relief and other protections.

GFCI protection (590.6)

590.6(A): all 125 V, single-phase, 15-, 20-, and 30-ampere receptacle outlets that are not part of the permanent wiring of the building or structure and are used by personnel must have GFCI protection for personnel. This includes receptacles on portable generators and those supplied from permanent wiring but used for temporary power, unless already protected.

590.6(B): other receptacle outlets used for temporary power, such as 250 V or higher-amperage receptacles, must also have ground-fault protection as described in 590.6(B), which recognizes Class A GFCIs and special-purpose GFCIs for higher-voltage circuits.

Listed cord sets or devices with GFCI protection may be used in some cases where permanent GFCI protection is not available.

Worked example: a Minnesota county fair

A county fair midway has a ride supplied from a portable generator and food stands supplied from temporary panels.

Ride location: keep the ride at least 15 ft in any direction from overhead distribution lines of 600 V or less, other than its own supply conductors.

Cords: listed extra-hard usage , wet-location and sunlight-resistant cords; across walkways, cover them with nonconductive mats.

Receptacles: 125 V, 15- and 20-ampere receptacles readily accessible to the public or used for setup are GFCI protected.

Temporary panels for the food stands: grounding-type receptacles, GFCI protected, with the wiring removed when the fair ends.