Study guide
19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680)
Minnesota Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Minnesota Exam, Licensing & Electrical Law
1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement
2 Electrical Theory, Math & Power Calculations
2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting
3 NEC Structure & General Requirements
3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)
4 Conductors, Identification & Ampacity
4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors
5 Branch Circuits, GFCI/AFCI & Required Outlets
5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)
6 Load Calculations (2026 NEC Article 120)
6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)
7 Feeders, Outside Wiring & Services
7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)
8 Overcurrent Protection
8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction
9 System Grounding & Grounding Electrodes
9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems
10 Bonding & Equipment Grounding
10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding
11 General Wiring Methods & Underground Installations
11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)
12 Raceways, Cables & Conduit Fill
12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)
13 Boxes, Conduit Bodies & Cabinets
13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)
14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances
14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)
15 Motors, Controllers & Air Conditioning
15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)
16 Transformers, Generators & Equipment Over 1000 Volts
16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)
17 Hazardous (Classified) Locations
17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)
18 Health Care, Assembly, Agricultural & Mobile Occupancies
18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)
19 Signs, Elevators, Pools, Solar & Other Specific Equipment
19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)
20 Emergency, Standby & Interconnected Power Sources
20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)
21 Limited-Energy, Fire Alarm & Communications Systems
21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)
19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680)
Key Takeaways Explain This Topic AI
NEC Article 680 establishes critical safety protocols to prevent Electric Shock Drowning (ESD) and electrocution in swimming pools, spas, hot tubs, and decorative fountains.
Equipotential bonding under NEC 680.26 eliminates voltage gradients across the pool shell, deck, water, and metal equipment by interconnecting them with a minimum 8 AWG solid copper conductor.
Perimeter surface bonding must extend 3 feet (1.0 m) horizontally beyond the inside walls of the pool, constructed with bonded structural steel, a copper conductor grid, or an 8 AWG solid copper conductor positioned 18 to 24 inches from the pool wall and 4 to 6 inches below subgrade.
Pool water bonding (NEC 680.26(C)) requires an intentional conductive surface of at least 9 square inches (5,800 mm²) in continuous direct contact with the pool water, connected to the equipotential bonding grid.
Outlets supplying pool motors need GFCI protection under 680.21(C) and 680.5: a Class A GFCI at 150 V or less to ground on single-phase circuits of 60 A or less and three-phase circuits of 100 A or less, and a special-purpose GFCI above 150 V to ground.
Last updated: October 2026
19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680)
Quick Answer: Under NEC Article 680 , swimming pools, spas, and hot tubs require an equipotential bonding grid constructed with a minimum 8 AWG solid copper conductor (NEC 680.26). This grid must bond the conductive pool shell , all perimeter surfaces extending 3 feet 3\text{ feet} 3 feet ( 1.0 m 1.0\text{ m} 1.0 m ) beyond the pool wall, all metallic pool components (ladders, handrails), all electrical circulation equipment (pump motors, heaters), and the pool water itself via a conductive surface of not less than 9 square inches 9\text{ square inches} 9 square inches ( 5,800 mm 2 5{,}800\text{ mm}^2 5 , 800 mm 2 ) . Under NEC 680.21(C) , all single-phase pool pump motors rated 60 A 60\text{ A} 60 A or less , operating at either 120 V 120\text{ V} 120 V or 240 V 240\text{ V} 240 V , must be equipped with GFCI protection to prevent Electric Shock Drowning (ESD) .
Water and electricity represent an intrinsically lethal combination. When a person is immersed in water, human body resistance drops dramatically—from thousands of ohms down to approximately 500 Ω 500\ \Omega 500 Ω —because moisture completely saturates the high-resistance outer skin layers. In this saturated state, electrical currents as tiny as 10 to 15 milliamperes (mA) 10\text{ to }15\text{ milliamperes (mA)} 10 to 15 milliamperes (mA) cause involuntary skeletal muscle paralysis ( tetany ). In a swimming pool, tetany prevents a swimmer from kicking, treading water, or calling for help, causing immediate submersion and death. This silent tragedy is known as Electric Shock Drowning (ESD) . Unlike standard electrocution, ESD victims show no electrical burns; the autopsy records drowning as the cause of death. To eliminate the electrical gradients that cause ESD, NEC Article 680 establishes comprehensive standards for equipotential bonding grids, pool water bonding, wiring raceways, luminaire enclosures, and mandatory GFCI protection.
Equipotential Bonding vs. Equipment Grounding: Distinct Safety Functions
One of the most frequent misconceptions on the Minnesota Journeyman exam is confusing equipment grounding under Article 250 with equipotential bonding under Article 680:
Safety Engineering Characteristic Equipment Grounding (NEC Article 250) Equipotential Bonding (NEC Article 680)
Primary Objective Establish an effective ground-fault current path to trip circuit breakers or fuses during an electrical fault. Eliminate voltage gradients across surfaces and water to prevent electrical current from flowing through swimmers.
Governing Conductor Sized per NEC Table 250.122 based on the branch-circuit overcurrent device rating (minimum 14, 12, or 10 AWG). Sized per NEC 680.26: Minimum 8 AWG solid copper conductor (bare or insulated).
Terminating Location Connects from equipment frames back to the grounding bus of the electrical distribution panelboard. Interconnects all conductive metal pool components, deck rebar, and water into a local conductive web.
Return to Earth Required? YES: Must connect back to the electrical source neutral/grounding electrode system to clear faults. NO: Does NOT require connection to an electrical panelboard or earth ground rod to perform its function!
In an unbonded swimming pool, stray voltage from an underground utility line, a faulty pool light, or a damaged pump motor can elevate the voltage of the concrete deck to 12 V 12\text{ V} 12 V while the pool water remains at 0 V 0\text{ V} 0 V . When a swimmer steps onto the deck while holding the metal ladder, the 12 V 12\text{ V} 12 V differential drives 24 mA 24\text{ mA} 24 mA across the chest cavity, causing instantaneous paralysis and drowning. In contrast, when the pool shell, deck, ladder, and water are interconnected into an equipotential bonding grid , all components rise to the exact same electrical potential ( 12 V 12\text{ V} 12 V ). Because there is zero potential difference ( Δ V = 0 V \Delta V = 0\text{ V} Δ V = 0 V ) between the swimmer's hands and feet, no current flows , and the swimmer remains completely unharmed.
The Equipotential Bonding Grid Components (NEC 680.26)
Under NEC 680.26(B) , an equipotential bonding grid must interconnect the following six discrete elements using a minimum 8 AWG solid copper conductor (bare or insulated) with listed non-reversible pressure connectors, listed exothermic welds, or stainless steel / copper ground clamps:
1. Conductive Pool Shell (NEC 680.26(B)(1))
Poured Concrete, Gunite, or Shotcrete Pools: The structural reinforcing steel rebar embedded within the pool floor and walls forms the primary bonding grid. Rebar sections must be secured together using standard steel tie wires at all intersections. If epoxy-coated rebar is used, it cannot serve as the bonding grid; an alternate grid must be installed.
Copper Grid Alternative: Where structural reinforcing steel is not available or is encapsulated in a nonconductive compound (such as epoxy-coated rebar) in a conductive shell, a copper grid of minimum 8 AWG bare solid copper conductors, arranged in a 12 in. by 12 in. network with a tolerance of 4 in., conforming to the contour of the pool and secured within or under the shell no more than 6 in. from its outer contour, is required.
Nonconductive Pool Shells (Fiberglass, Vinyl Liner): a nonconductive shell does not itself require a bonding grid, but the perimeter surfaces, metal parts, equipment, and pool water must still be bonded.
2. Perimeter Surfaces (NEC 680.26(B)(2))
The equipotential plane must extend horizontally 3 feet 3\text{ feet} 3 feet ( 1.0 m 1.0\text{ m} 1.0 m ) beyond the inside walls of the pool, covering all walking decks, paved copings, and unpaved soil surfaces surrounding the pool perimeter:
Paved Surfaces with Structural Steel (Concrete Decks): Structural steel reinforcing rebar or welded wire reinforcement mesh within the concrete walking deck must be bonded to the pool shell grid at a minimum of four points uniformly spaced around the pool perimeter.
Unpaved Surfaces, Pavers, or Decks Without Structural Steel: Where the deck consists of unreinforced concrete, brick pavers, wood decking, or bare turf, a perimeter copper bonding loop must be installed:
Constructed of a single continuous minimum 8 AWG solid copper conductor .
Installed between 18 inches 18\text{ inches} 18 inches and 24 inches 24\text{ inches} 24 inches ( 450 to 600 mm 450\text{ to }600\text{ mm} 450 to 600 mm ) horizontally from the inside wall of the pool.
Buried between 4 inches 4\text{ inches} 4 inches and 6 inches 6\text{ inches} 6 inches ( 100 to 150 mm 100\text{ to }150\text{ mm} 100 to 150 mm ) below finished subgrade.
Secured and bonded to the pool shell conductive grid at a minimum of four uniformly distributed points around the pool perimeter.
3. Metallic Components (NEC 680.26(B)(5))
All metal fittings and structural components within or attached to the pool structure must be bonded to the 8 AWG grid. This includes metal ladder anchor sockets, stainless steel handrails, diving board metal supports, and motorized pool cover mounting tracks.
Small Part Exception (NEC 680.26(B)(5) Ex.): Isolated metal parts not exceeding 4 inches 4\text{ inches} 4 inches ( 100 mm 100\text{ mm} 100 mm ) in any dimension that do not penetrate the pool structure and are not likely to become energized (such as decorative tile trim or nameplates) are not required to be bonded.
4. Underwater Lighting Forming Shells (NEC 680.26(B)(4))
The wet-niche forming shells and mounting brackets for all underwater luminaires must be bonded directly to the 8 AWG solid copper equipotential grid.
5. Electrical Equipment (NEC 680.26(B)(6))
All metal housings and mounting frames of electrical pool equipment must be bonded to the 8 AWG grid, including circulation pump motors, electric pool heaters, heat pumps, automated chemical controllers, and air blowers.
Double-Insulated Pump Motor Exception (NEC 680.26(B)(6)(a)): Where a listed double-insulated pool pump motor is installed, an 8 AWG solid copper bonding wire must still be run from the equipotential grid to the pump motor equipment pad. The bonding conductor is coiled and left available at the pump pad so that if the double-insulated pump is replaced in the future with a conventional metal-framed motor, an approved bonding connection is immediately available.
Pool Water Bonding Mandates (NEC 680.26(C))
Prior to the 2008 NEC, electricians bonded the metal shell, ladder, and pump, but neglected the pool water itself. Because water is an electrical conductor, an electrical charge can accumulate in the water mass relative to earth. A bather sitting on a bonded concrete deck who dips their hand or foot into unbonded water can receive a paralyzing ESD shock.
Under NEC 680.26(C) , the pool water must be intentionally bonded to the equipotential grid with an approved conductive surface satisfying the following criteria:
Minimum Surface Area: The conductive bonding component must provide not less than 9 square inches 9\text{ square inches} 9 square inches ( 5,800 mm 2 5{,}800\text{ mm}^2 5 , 800 mm 2 ) of exposed conductive surface in direct contact with the pool water at all times.
Corrosion Resistance: The bonding surface must be constructed of listed corrosion-resistant materials (such as stainless steel, brass, copper, or titanium sacrificial anodes).
Continuous Water Contact: The component must remain in contact with the water under normal pool operation, located either:
In the pool wall (such as an embedded conductive plate).
Inside the skimmer basket assembly (such as a bonded stainless steel skimmer plate).
Inside the pool water circulation piping system (such as an in-line metallic pipe spool piece or metallic heater manifold).
Forming Shell Compliance: A wet-niche underwater luminaire with a brass or stainless steel forming shell providing at least 9 sq inches 9\text{ sq inches} 9 sq inches of water contact area satisfies the water bonding requirement without requiring an additional pipe fitting.
GFCI Protection for Pool Equipment & Receptacles (NEC 680.21 & 680.22)
Ground-Fault Circuit-Interrupters provide the secondary line of defense against electrocution by de-energizing branch circuits within 25 milliseconds 25\text{ milliseconds} 25 milliseconds when ground-fault leakage current exceeds 4 to 6 mA 4\text{ to }6\text{ mA} 4 to 6 mA .
Pool Pump Motors (NEC 680.21(C) and 680.5)
Under NEC 680.21(C) , outlets supplying pool motors must have ground-fault protection meeting 680.5 : a Class A GFCI where the circuit is 150 V or less to ground and rated 60 A or less single-phase or 100 A or less three-phase , and a special-purpose GFCI (SPGFCI) where the circuit is over 150 V to ground . When a pool pump motor is replaced for maintenance or repair, the replacement must also have GFCI protection (680.21(D)).
Critical Journeyman Rule: The 240-volt pool pump motor is NOT exempt from GFCI protection! Even hard-wired, permanently installed 240 V 240\text{ V} 240 V two-pole pump motors require two-pole GFCI circuit breakers.
Receptacle Placement and Protection (NEC 680.22(A))
Prohibited Zone (0 to 6 Feet): Receptacles are strictly prohibited within 6 feet 6\text{ feet} 6 feet ( 1.8 m 1.8\text{ m} 1.8 m ) of the inside walls of a swimming pool.
Circulation and Sanitation Receptacles (NEC 680.22(A)(2)): Receptacles supplying water-pump motors or other circulation and sanitation loads must be at least 6 feet (1.8 m) from the inside walls of the pool and must be GFCI protected . The older 6-to-10-foot single locking receptacle option no longer applies.
Mandatory Convenience Receptacle (NEC 680.22(A)(1)): For permanently installed pools at dwelling units, at least one 125-volt, 15- or 20-ampere general-purpose receptacle must be installed between 6 feet 6\text{ feet} 6 feet and 20 feet 20\text{ feet} 20 feet ( 1.8 to 6.0 m 1.8\text{ to }6.0\text{ m} 1.8 to 6.0 m ) from the inside wall of the pool, located not more than 6 feet , 6 inches 6\text{ feet }, 6\text{ inches} 6 feet , 6 inches ( 2.0 m 2.0\text{ m} 2.0 m ) above the deck.
Universal GFCI Mandate (NEC 680.22(A)(4)): All 15- and 20-ampere, single-phase, 125-volt through 250-volt receptacles located within 20 feet 20\text{ feet} 20 feet ( 6.0 m 6.0\text{ m} 6.0 m ) of the inside walls of a pool or fountain must be provided with GFCI protection.
Luminaires, Lighting Outlets & Ceiling Fans (NEC 680.22(B))
Clearance Height: New outdoor luminaires, lighting outlets, and ceiling fans installed directly over a pool or within 5 feet 5\text{ feet} 5 feet ( 1.5 m 1.5\text{ m} 1.5 m ) horizontally from the inside walls must be installed not less than 12 feet 12\text{ feet} 12 feet ( 3.7 m 3.7\text{ m} 3.7 m ) above the maximum water level. The 2026 NEC applies these heights to festoon lighting as well.
GFCI Exception: Existing luminaires located less than 5 feet 5\text{ feet} 5 feet horizontally from the pool edge may remain if installed at least 5 feet 5\text{ feet} 5 feet above maximum water level and protected by a GFCI.
Low-Voltage Contact Limit (NEC 680.2): Luminaires operating at or below the low-voltage contact limit ( 15 V 15\text{ V} 15 V RMS AC or 30 V 30\text{ V} 30 V continuous DC ) and supplied by a listed swimming pool isolation transformer or power supply are permitted closer to the water without individual GFCI protection, as their potential is insufficient to drive dangerous current through human tissue.
- Underwater Luminaires & Junction Boxes (NEC 680.23 & 680.24)
- Wet-Niche Luminaire Wiring & Grounding (NEC 680.23)
Wet-niche luminaires operate submerged in water inside an open forming shell:
Raceway Requirement: Conduit must extend from the wet-niche forming shell to a suitable junction box or enclosure. Metal conduit must be brass or another approved corrosion-resistant metal ; where nonmetallic conduit is used, an 8 AWG insulated (solid or stranded) copper bonding jumper must be installed in it, unless a listed low-voltage lighting system not requiring grounding is used.
Insulated Equipment Grounding Conductor: An insulated copper equipment grounding conductor , sized in accordance with NEC Table 250.122 but never smaller than 12 AWG copper , must be pulled inside the raceway.
Potting Compound (NEC 680.23(B)(2)(b)): Where PVC conduit is used, the termination of the 8 AWG insulated copper bonding jumper inside the wet-niche forming shell must be encapsulated in a listed potting compound (such as two-part epoxy) to protect the copper terminal from chlorine and saltwater corrosion.
Swimming Pool Junction Boxes (NEC 680.24)
Junction boxes connecting submerged underwater luminaires must be specialized, listed swimming pool junction boxes constructed of cast brass, bronze, stainless steel, or heavy-duty nonmetallic polymers:
Distance from Pool Edge (NEC 680.24(A)(2)(b)): The junction box must be installed not less than 4 feet 4\text{ feet} 4 feet ( 1.2 m 1.2\text{ m} 1.2 m ) horizontally from the inside wall of the pool (unless separated by a permanent solid wall or barrier).
Elevation Above Ground/Deck (NEC 680.24(A)(2)(a)): The junction box must be installed not less than 4 inches 4\text{ inches} 4 inches ( 100 mm 100\text{ mm} 100 mm ) above the finished ground level or pool deck surface.
Elevation Above Maximum Water Level (NEC 680.24(A)(2)(a)): The junction box must be installed not less than 8 inches 8\text{ inches} 8 inches ( 200 mm 200\text{ mm} 200 mm ) above the maximum pool water level (whichever elevation is higher). This critical elevation prevents water from siphoning back through the conduit into the electrical system if conduit seals fail.