Study guide
21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)
Minnesota Journeyman Electrician Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Minnesota Exam, Licensing & Electrical Law
1.1 Exam Format, Provided References, Scoring & Scheduling 1.2 The Minnesota Electrical Act, Board of Electricity & Code Adoption 1.3 Personal Licenses, Scope of Work & Electrical Contractors 1.4 Experience Credit, Registration, Reciprocity, Renewal & Continuing Education 1.5 Direct Supervision, Ratios & Licensing Exemptions 1.6 Electrical Permits, Inspections, Condemnation & Enforcement
2 Electrical Theory, Math & Power Calculations
2.1 Exam Math, Ohm's Law, Watt's Law & Series/Parallel Circuits 2.2 AC Fundamentals: Reactance, Impedance & Power Factor 2.3 Three-Phase Systems: Wye vs. Delta Calculations 2.4 Voltage Drop Calculations & Chapter 9 Conductor Properties 2.5 Transformer Ratios, Connections, Taps & Available Fault Current 2.6 Motor Connections, Control Circuits & Troubleshooting
3 NEC Structure & General Requirements
3.1 Navigating the 2026 NEC: Article 90, Code Structure & Article 100 Definitions 3.2 NEC Article 110: Working Clearances, Dedicated Space & Termination Ratings 3.3 Over-1000-Volt Installations, Guarding & Manholes (Article 110, Parts III–V)
4 Conductors, Identification & Ampacity
4.1 Conductor Insulation Types, Copper vs. Aluminum & Table 310.16 Allowable Ampacities 4.2 Ampacity Derating: Ambient Temperature Correction & Raceway Bundling Adjustments 4.3 Conductor Identification, Splices & Parallel Conductors
5 Branch Circuits, GFCI/AFCI & Required Outlets
5.1 Branch Circuit Sizing, Overcurrent Ratings & Multiwire Branch Circuits 5.2 GFCI & AFCI Protection Requirements (NEC 210.8 & 210.12) 5.3 Dwelling Receptacle Outlets, Required Circuits & Lighting Outlets (NEC 210.11, 210.52, 210.63 & 210.70)
6 Load Calculations (2026 NEC Article 120)
6.1 Article 120 Basics: Dwelling Lighting, Small-Appliance & Laundry Loads 6.2 Dwelling Standard Method: Appliances, Dryers, Ranges, Heating, EVSE & Neutral 6.3 Optional Methods: Single Dwelling, Existing Dwelling & Multifamily (2026 NEC 120.82–120.85) 6.4 Commercial Lighting, Receptacle, Sign & Show-Window Loads (Table 120.42(A) & 120.44) 6.5 Commercial Kitchens, Schools & Restaurants (2026 NEC 120.56, 120.86 & 120.88) 6.6 Farm Load Calculations (2026 NEC 120.102 & 120.103) 6.7 Feeder & Service Neutral Sizing (2026 NEC 120.61)
7 Feeders, Outside Wiring & Services
7.1 Feeder Design & Sizing Requirements (NEC Article 215) 7.2 Outside Feeders & Separate Buildings (Article 225 & 250.32) 7.3 Service Clearances, Overhead Drops & Underground Service Laterals 7.4 Service Equipment, Disconnecting Means, Surge Protection & GFPE (2026 NEC Article 230)
8 Overcurrent Protection
8.1 Overcurrent Protective Devices: Fuses, Breakers & Standard Ampere Ratings 8.2 Conductor Overcurrent Protection & Feeder Tap Rules (NEC 240.4 & 240.21) 8.3 OCPD Location, Breaker Voltage Ratings, Handle Ties & Arc Energy Reduction
9 System Grounding & Grounding Electrodes
9.1 Grounding vs. Bonding Principles & System Grounding (NEC Article 250 Parts I-II) 9.2 Grounding Electrode System: Permitted Electrodes & Installation (NEC 250.50 & 250.52) 9.3 Grounding Electrode Conductor (GEC) Sizing & Protection (NEC Table 250.66) 9.4 Main Bonding Jumper, System Bonding Jumper & Separately Derived Systems
10 Bonding & Equipment Grounding
10.1 Equipment Grounding Conductor (EGC) Types, Identification & Sizing (NEC Table 250.122) 10.2 Proportional Upsizing of EGC for Voltage Drop (NEC 250.122(B)) 10.3 Bonding of Interior Metal Piping, Structural Steel & Other Systems (NEC 250.104) 10.4 Bonding Methods, Equipment Requiring Grounding & Receptacle Grounding
11 General Wiring Methods & Underground Installations
11.1 General Wiring Methods & Mechanical Protection (NEC Article 300) 11.2 Underground Wiring Cover Requirements (NEC Table 300.7) 11.3 Securing & Supporting, Plenums, Firestopping & Raceway Installation (Article 300)
12 Raceways, Cables & Conduit Fill
12.1 Metal (RMC, IMC, EMT) & Nonmetallic (PVC, RTRC, LFNC) Raceways 12.2 Flexible Conduits, ENT, Wireways, Auxiliary Gutters & Surface Raceways 12.3 Busways & Cable Tray Systems (Articles 368 & 392) 12.4 Cable Assemblies (NM, UF, MC) & Minnesota Cold-Weather Installation Rules 12.5 Conduit & Tubing Fill Calculations (Chapter 9 & Annex C)
13 Boxes, Conduit Bodies & Cabinets
13.1 Box Installation, Support, Accessibility & Luminaire and Fan Boxes (Article 314) 13.2 Outlet, Switch & Junction Box Fill Calculations (NEC 314.16) 13.3 Pull and Junction Box Sizing for Conductors 4 AWG & Larger (NEC 314.28) 13.4 Cabinets, Cutout Boxes & Wire Bending Space (NEC Article 312)
14 Cords, Wiring Devices, Panelboards, Luminaires & Appliances
14.1 Flexible Cords, Flexible Cables & Fixture Wires (Articles 400 & 402) 14.2 Switches, Receptacles & Wiring Devices (Articles 404 & 406) 14.3 Panelboards, Switchboards & Switchgear (NEC Article 408) 14.4 Luminaires, Lampholders, Lighting Track & Low-Voltage Lighting (Articles 410 & 411) 14.5 Appliances, Fixed Electric Space Heating & Deicing Equipment (Articles 422, 424 & 426)
15 Motors, Controllers & Air Conditioning
15.1 Motor Full-Load Current Determination & Conductor Sizing (NEC 430.6 & 430.22) 15.2 Motor Branch-Circuit Short-Circuit & Ground-Fault Protection (NEC Table 430.52) 15.3 Motor Overload Protection & Feeder Calculations for Multiple Motors (NEC 430.32 & 430.24) 15.4 Motor Controllers, Disconnecting Means, Drives & Motor Control Centers (Article 430 Parts VII–XI) 15.5 Air Conditioning & Refrigeration Equipment (NEC Article 440)
16 Transformers, Generators & Equipment Over 1000 Volts
16.1 Transformer Overcurrent Protection & Sizing (NEC Article 450) 16.2 Generators & Transfer Switches (NEC Article 445) 16.3 Capacitors, Transformers Over 1000 V & Medium-Voltage Equipment (Articles 460, 450 & 495)
17 Hazardous (Classified) Locations
17.1 Hazardous (Classified) Locations: Classes, Divisions & Zones (NEC Articles 500-506) 17.2 Class I Locations: Wiring Methods & Conduit Seal-Offs (NEC Article 501) 17.3 Class II & Class III Locations and the Zone System (Articles 502, 503, 505 & 506) 17.4 Commercial Garages & Motor Fuel Dispensing Facilities (NEC Articles 511 & 514) 17.5 Spray Areas, Aircraft Hangars, Hazardous-Location Bonding & Intrinsic Safety (Articles 500, 504, 513 & 516)
18 Health Care, Assembly, Agricultural & Mobile Occupancies
18.1 Health Care Facilities: Patient Care Spaces & Redundant Grounding (NEC Article 517) 18.2 Places of Assembly, Carnivals & Fairs, and Temporary Installations (Articles 518, 525 & 590) 18.3 Agricultural Buildings, Equipotential Planes & Farm Distribution Points (Article 547) 18.4 Mobile & Manufactured Homes, RV Parks, and Marinas & Docks (Articles 550, 551 & 555)
19 Signs, Elevators, Pools, Solar & Other Specific Equipment
19.1 Signs & Outline Lighting, Office Partitions, IT Rooms & Irrigation Machines (Articles 600, 605, 645 & 675) 19.2 Elevators, Escalators & Platform Lifts (Article 620) 19.3 Swimming Pools, Spas & Water Features: Equipotential Bonding & GFCI (NEC Article 680) 19.4 Spas, Hot Tubs, Hydromassage Bathtubs, Fountains & Natural Bodies of Water (Article 680 Parts IV–VII & Article 682) 19.5 Solar Photovoltaic Systems (Article 690) 19.6 Small Wind Systems, Fire Pumps & Electric Vehicle Charging (Articles 694, 695 & 625)
20 Emergency, Standby & Interconnected Power Sources
20.1 Emergency Systems vs. Legally Required vs. Optional Standby (NEC Articles 700, 701, 702) 20.2 Interconnected Power Sources, Energy Storage & Power Control Systems (Articles 705, 706, 480 & 130)
21 Limited-Energy, Fire Alarm & Communications Systems
21.1 Remote-Control, Signaling & Power-Limited Circuits: Class 1, 2 & 3 (2026 Articles 206, 720–725) 21.2 Class 4 Fault-Managed Power, Tray Cables, Fire-Resistive Cable Systems & Limited-Energy Grounding (Articles 726, 727, 742, 750 & 772) 21.3 Fire Alarm Systems: NPLFA vs. PLFA Wiring & Overcurrent Protection (NEC Article 760) 21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)
21.4 Optical Fiber Cables & Communications Systems Entering Buildings (2026 Articles 720–723, 800, 810, 820)
Key Takeaways Explain This Topic AI
Optical fiber cables are nonconductive (OFN types, no metallic members), conductive (OFC types, with non-current-carrying metallic members), or composite (fibers plus current-carrying conductors).
Nonconductive optical fiber cables may share a raceway or cable tray with power, Class 1, or nonpower-limited fire alarm conductors of 1000 V or less, but conductive optical fiber cables may not.
Unlisted outside plant communications or optical fiber cable may extend no more than 50 ft inside a building from its point of entrance before terminating in an enclosure or listed protector.
The bonding conductor for a communications primary protector must be copper, insulated, at least 14 AWG, and, at one- and two-family dwellings, not longer than 20 ft unless a separate electrode is used and bonded to the power electrode system with 6 AWG copper.
In the 2026 NEC, Article 800 covers only communications wiring outside and entering buildings; inside buildings, communications cabling follows the Chapter 7 limited-energy rules.
Last updated: October 2026
What changed in 2026
The 2026 NEC removed the independence of Chapter 8 and consolidated limited-energy wiring:
Articles 770 (Optical Fiber Cables) and 805 (Communications Circuits) were deleted. Their inside-the-building requirements moved into Articles 720 (general wiring methods), 722 (cables, including listing, marking, and substitutions), and 723 (raceways, cable routing assemblies, and cable trays).
Article 800 now covers communications systems outside and entering buildings : entrance cables, primary protection, and bonding at the entrance.
Article 742 covers overvoltage protection and Article 750 covers grounding and bonding for limited-energy systems.
Articles 810 (radio and television equipment), 820 (community antenna television and radio distribution), 830 (network-powered broadband), and 840 (premises-powered broadband) continue for their specific systems.
Optical fiber cable types
Type Construction Markings
Nonconductive No metallic members; strength members are nonmetallic, such as aramid yarn OFNP (plenum), OFNR (riser), OFNG or OFN (general purpose)
Conductive Non-current-carrying conductive members, such as metallic strength members, armor, or vapor barriers OFCP , OFCR , OFCG or OFC
Composite Optical fibers plus current-carrying electrical conductors Listed and marked under the article for the electrical conductors, such as power or Class 2
Cable substitutions
A cable with a higher fire rating may replace a lower one in the same space: plenum cable may be used where riser or general-purpose cable is required, and riser cable where general-purpose cable is required. Nonconductive cable may substitute for conductive cable of the same or lower rating (for example, OFNP for OFCP or OFCR), but conductive cable may not substitute for nonconductive cable. Plenum spaces need plenum-rated cable or cable in a raceway suitable for the plenum.
Optical fiber with electrical conductors
Situation Rule
Nonconductive fiber in the same raceway or cable tray with conductors of electric light, power, Class 1, NPLFA, or medium-power broadband circuits of 1000 V or less Permitted
Conductive fiber in the same raceway or cable tray with those conductors Not permitted
Composite fiber cables containing only power or Class 1 conductors of 1000 V or less May share enclosures and raceways with power and Class 1 conductors of 1000 V or less
Nonconductive fiber in the same cabinet, box, panel, or enclosure that houses the terminations of power, Class 1, or NPLFA circuits Not permitted , unless the fiber is functionally associated with that equipment, in factory- or field-assembled control centers, or in industrial establishments with qualified maintenance
Fiber with Class 2, Class 3, communications, and PLFA cables Permitted in the same raceway, enclosure, or cable tray
Installation inside buildings (Articles 720 to 723)
Cables must be supported by the building structure , not by ceiling grids or ceiling-support wires, and installed so they do not block access to equipment above suspended ceilings.
Penetrations of fire-resistant-rated walls, floors, and ceilings must be firestopped .
Abandoned optical fiber and communications cables: the accessible portion must be removed, unless tagged for future use.
Cables in plenums must be plenum rated; cables in vertical risers between floors must be riser rated or in a raceway or fireproof shaft as permitted.
Raceways and cable routing assemblies used for these cables must have the same fire rating as the space (plenum, riser, or general purpose).
- Communications entering buildings (Article 800)
- Entrance cables
Unlisted outside plant cable: unlisted communications or optical fiber cable may be installed in building spaces other than risers and plenums where the length within the building , measured from the point of entrance , does not exceed 50 ft , and the cable terminates in an enclosure or on a listed primary protector. The point of entrance may be extended by enclosing the entrance cable in RMC or IMC to the point of emergence.
Conductive members: the metallic members of conductive optical fiber cable and the metallic sheath of communications cable entering a building must be bonded or grounded as close as practicable to the point of entrance .
Primary protectors and bonding
A listed primary protector is required on each communications circuit that is exposed to lightning or accidental contact with power conductors, located as close as practicable to the point of entrance.
Bonding conductor: copper or other corrosion-resistant conductive material, insulated , at least 14 AWG , with a current-carrying capacity at least equal to the outer sheath or protected conductors, run as straight as practicable , and protected where exposed to physical damage.
Connection point: to the building's intersystem bonding termination (250.94), or to the grounding electrode system, the power service equipment enclosure, the grounding electrode conductor, or another permitted point.
Length at one- and two-family dwellings: the bonding conductor or grounding electrode conductor must be as short as practicable and not longer than 20 ft . If 20 ft cannot be achieved, a separate electrode (such as a ground rod) may be installed for the protector and bonded to the power grounding electrode system with at least 6 AWG copper .
Antennas and CATV
Radio and television antennas (Article 810): masts and metal structures supporting antennas, and the antenna discharge unit, must be bonded to the building's grounding means with a copper bonding conductor of at least 10 AWG for receiving stations; outdoor antennas and lead-ins must be kept away from power conductors and may not be attached to poles carrying power circuits over 250 V.
CATV (Article 820): the outer conductive shield of coaxial cable entering a building must be bonded as close as practicable to the point of entrance, with the same 14 AWG minimum and 20 ft dwelling limit for the bonding conductor; unlisted outside coaxial cable may extend no more than 50 ft inside.
Worked example: fiber in a commercial building
A contractor brings a single-mode fiber cable with a steel armor (conductive, OFC-type outside plant cable) into a building and runs it to a telecom room 120 ft away.
Entrance: the unlisted outside plant cable may extend only 50 ft inside unless enclosed in RMC or IMC from the point of entrance; at the 50 ft limit, splice it in an enclosure to a listed indoor cable.
Bonding: bond the steel armor as close as practicable to the point of entrance, to the intersystem bonding termination.
Indoor cable: the route passes through a return-air plenum, so the indoor cable must be OFNP or OFCP , or be in a plenum-rated raceway.
Shared raceway: if it must share a raceway with 277 V lighting conductors, only a nonconductive (OFN-type) cable is permitted.