Study guide
10.5 Foam Plastic Insulation & Interior Finishes (Drywall)
Minnesota General Contractor Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Minnesota Licensing Statutes & DLI Regulatory Framework
1.1 Scope of Practice, License Types & DLI Administration 1.2 Qualifying Person Requirements & Continuing Education 1.3 Exemptions, Prohibited Acts & DLI Enforcement
2 Chapter 2: Minnesota Contract Law & Statutory Home Warranties
2.1 Essential Terms of Construction Contracts & Change Orders 2.2 Statutory Warranties under Minn. Stat. Chapter 327A 2.3 Insurance Deductible Rebates & Contractor Recovery Fund
3 Chapter 3: Minnesota Mechanics Lien Law (Minn. Stat. Chapter 514)
Section 3.1: Pre-Lien Notice Requirements for Prime & Subcontractors Section 3.2: Recording Mechanics Liens & The 120-Day Filing Deadline Section 3.3: Foreclosure Actions, Priority & Lien Waivers
4 Chapter 4: Business Management, Accounting & Taxes
4.1 Financial Statements, Cash vs. Accrual Accounting & Cash Flow 4.2 Minnesota Business Structures, State Taxes & Capital Improvements 4.3 Payroll Management, Prevailing Wage & Employer Tax Obligations
5 Chapter 5: Risk Management, Insurance & Surety Bonds
Section 5.1: Commercial General Liability & Workers' Compensation Insurance Section 5.2: Surety Bonds vs. Insurance (Bid, Performance & Payment Bonds) Section 5.3: Risk Assessment, Subcontractor Certificates & Indemnification
6 Chapter 6: Jobsite Safety & Minnesota OSHA Compliance
6.1 MN OSHA Regulations, Inspections & Employer Rights 6.2 Fall Protection, Scaffolding & Personal Protective Equipment 6.3 Trenching, Excavation, Hazard Communication & Silica Standards
7 Chapter 7: Minnesota State Building Code Administration & Permits
7.1 MN Rules Chapter 1300 (Administration, Permits & Plan Review) 7.2 Building Inspections, Code Violations & Certificates of Occupancy 7.4 Building Planning: Means of Egress, Stairways, Exit Doors & Garage Separation 7.5 Life Safety: Smoke Alarms, Safety Glazing, Natural Light, Ceiling Heights & Replacement Windows 7.3 Site Preparation, Surveying & Soil Bearing Capacity
8 Chapter 8: Foundations, Footings, Concrete & Masonry
8.1 Frost Depth Requirements, Soils & Footing Design 8.2 Foundation Wall Systems, Waterproofing & Damp-Proofing 8.3 Concrete Specifications, Reinforcement & Cold-Weather Concreting
9 Chapter 9: Wood Framing, Structural Systems & Load Requirements
9.1 Floor Systems, Girders & Joist Spanning 9.2 Wall Framing, Shear Walls & Structural Headers 9.3 Roof Framing, Trusses, Snow Load & Wind Load Design 9.4 Decks, Balconies, Stairs, Decay Protection & Wood Foundations
10 Chapter 10: Building Enclosure, Energy Code & Environmental Systems
10.1 Roofing Underlayment, Ice Dam Protection & Flashing Details 10.2 Insulation (R-Values), Vapor Retarders & MN Energy Code (Chapter 1322) 10.3 Radon Control Measures (Chapter 1303) & Indoor Air Quality 10.4 Exterior Finishes: House Wrap, Flashing, Siding, Stucco & Brick Veneer 10.5 Foam Plastic Insulation & Interior Finishes (Drywall) 10.6 Roof Covering Materials: Asphalt, Rolled Roofing & Wood Shingles/Shakes 10.7 Associated Issues: Electrical & Plumbing Awareness for Builders
10.5 Foam Plastic Insulation & Interior Finishes (Drywall)
Key Takeaways Explain This Topic AI
Foam plastic insulation must be tested to a maximum flame spread index of 75 and smoke-developed index of 450, but that rating alone does not permit the foam to be left exposed inside a dwelling.
A thermal barrier — typically 1/2-inch gypsum wallboard, limiting unexposed-surface temperature rise to 250°F after 15 minutes of fire exposure — is required wherever foam plastic is installed on the interior of occupiable space.
A lighter-duty ignition barrier (such as 1.5-inch mineral fiber insulation, 3/8-inch particleboard, or 3/8-inch gypsum) satisfies foam plastic exposed within attics or crawl spaces accessed for more than utility service.
The exposed-foam exception in attics/crawl spaces accessed only for utility service applies only when both the limited-access condition and a specific tested product listing (commonly AC377 Appendix X) are met.
Ceiling gypsum board requires 5/8-inch minimum thickness at 24-inch framing spacing (versus 1/2-inch at tighter spacing) to resist sag, and water-resistant gypsum board may not be used as a tile backer inside tub or shower enclosures.
Last updated: July 2026
Foam Plastic Insulation & Interior Finishes (Drywall)
Minnesota's 2020 Residential Code incorporates IRC Section R316 (foam plastic) and R702 (interior covering) with statewide amendments. Because foam plastic insulation is a combustible material even when it performs well thermally, the code layers multiple fire-separation requirements on top of the standard R-value rules — and this is where exam candidates most often lose points by confusing "thermal barrier" with "ignition barrier."
1. Flame Spread and Smoke-Developed Limits
All foam plastic insulation installed in a dwelling — rigid board, spray polyurethane, or foam sheathing — must be tested per ASTM E84 or UL 723 and carry a maximum:
- Flame spread index of 75
- Smoke-developed index of 450
This rating alone does not permit foam plastic to be left exposed inside a home. It only establishes that the material is acceptable for use behind a required fire-separation layer.
2. Thermal Barriers: The Interior Separation Requirement
Wherever foam plastic insulation is installed on the interior of a building — for example, spray foam on the underside of roof sheathing in a finished attic, or rigid foam on a basement wall — it must be separated from the habitable space by an approved thermal barrier equal to 1/2-inch gypsum wallboard , or another material demonstrated by testing to limit the average temperature rise of the unexposed surface to not more than 250°F after 15 minutes of fire exposure.
- Requirement Thermal Barrier
- Standard compliance material 1/2-inch gypsum wallboard
- Performance standard ≤250°F average surface temperature rise after 15 minutes of fire exposure
Where required Interior side of foam plastic in habitable/occupiable space (walls, ceilings, finished basements)
- Exception Specific foam products tested as an assembly and listed without a separate thermal barrier
- 3. Ignition Barriers: Attics and Crawl Spaces
A less stringent but still mandatory layer applies where foam plastic is exposed within an attic or crawl space that is entered for reasons beyond servicing utilities (e.g., storage attics, mechanical rooms). Because a full 1/2-inch gypsum thermal barrier is often impractical to install against a roof deck or foundation wall in these spaces, the code instead permits an ignition barrier , consisting of any one of:
- 1.5-inch-thick mineral fiber insulation
- 0.5-inch-thick structural cellulosic insulating board
- 0.25-inch-thick hardboard
- 0.375-inch-thick particleboard
- 0.375-inch gypsum board
- Corrosion-resistant steel a minimum of 0.016 inch thick
- Any other material tested and listed as an ignition barrier for the specific foam product
Exception (attic/crawl space access-only): An ignition barrier is not required where the attic or crawl space is accessed only to service utilities (not used for storage) and the installed spray foam product has been specifically tested and listed for exposed application without an ignition barrier (commonly certified under AC377 Appendix X). This exception is a frequent trick point on the exam — the exemption depends on both limited access and a specific product listing, not on either condition alone.
4. Exterior Continuous Insulation (Foam Sheathing)
Rigid foam sheathing applied to the exterior of framing as continuous insulation is treated differently because it sits outside the structural wall, not inside occupied space. It must still be covered by an approved exterior wall covering (siding, stucco, or brick veneer) fastened per the manufacturer's or code-prescribed schedule, and it must integrate with — not replace — the water-resistive barrier unless the specific foam product is also listed as a WRB with taped, sealed seams. Where foam sheathing thickness exceeds what standard-length siding nails can penetrate through into framing, longer fasteners or an engineered furring/fastening system rated for the additional foam thickness is required to maintain both structural attachment and weather-tightness.
5. Interior Finishes: Gypsum Board (R702)
Gypsum wallboard thickness and fastening are governed by framing spacing, since sag resistance decreases as spacing increases:
- Application Framing Spacing Minimum Thickness
- Wall, perpendicular application 16" o.c. 1/2 inch
- Wall, perpendicular application 24" o.c. 1/2 inch
- Ceiling, perpendicular application 16" o.c. 1/2 inch
- Ceiling, perpendicular application 24" o.c. 5/8 inch
Ceilings at wider 24-inch spacing require the thicker 5/8-inch board specifically to resist visible sag between joists over time — a detail candidates should remember as "wider ceiling spacing needs thicker board," even without memorizing every table cell.
Fastening spacing also tightens for ceilings versus walls: nails are typically spaced no more than 7 inches on center on ceilings and 8 inches on center on walls, while screws allow wider spacing (around 12 inches on center in the field) because their holding power per fastener is greater than a nail's.
6. Water-Resistant Gypsum Board in Wet Areas
Water-resistant gypsum board ("greenboard") may be used as a general wall substrate in bathrooms and kitchens, but it has firm limits:
It may not be used as a tile backer directly inside tub or shower enclosures — cement board, fiber-cement backer board, or another moisture-rated tile substrate is required there instead.
It may not be installed over a vapor retarder within a shower or tub enclosure, since trapped moisture behind the board accelerates core deterioration.
It is unsuitable in areas of sustained high humidity without mechanical ventilation, such as unvented steam shower enclosures.
Exam Takeaway
Two separate fire-protection concepts govern foam plastic — a thermal barrier (1/2-inch gypsum standard) for occupied interior space, and a lighter ignition barrier for attics/crawl spaces, with a narrow access-and-listing exception between them. Layer that distinction on top of standard gypsum board thickness and moisture-substrate rules, and this section becomes a set of predictable, memorizable comparisons rather than a wall of code citations.