Study guide
10.6 Roof Covering Materials: Asphalt, Rolled Roofing & Wood Shingles/Shakes
Minnesota General Contractor Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Minnesota Licensing Statutes & DLI Regulatory Framework
1.1 Scope of Practice, License Types & DLI Administration 1.2 Qualifying Person Requirements & Continuing Education 1.3 Exemptions, Prohibited Acts & DLI Enforcement
2 Chapter 2: Minnesota Contract Law & Statutory Home Warranties
2.1 Essential Terms of Construction Contracts & Change Orders 2.2 Statutory Warranties under Minn. Stat. Chapter 327A 2.3 Insurance Deductible Rebates & Contractor Recovery Fund
3 Chapter 3: Minnesota Mechanics Lien Law (Minn. Stat. Chapter 514)
Section 3.1: Pre-Lien Notice Requirements for Prime & Subcontractors Section 3.2: Recording Mechanics Liens & The 120-Day Filing Deadline Section 3.3: Foreclosure Actions, Priority & Lien Waivers
4 Chapter 4: Business Management, Accounting & Taxes
4.1 Financial Statements, Cash vs. Accrual Accounting & Cash Flow 4.2 Minnesota Business Structures, State Taxes & Capital Improvements 4.3 Payroll Management, Prevailing Wage & Employer Tax Obligations
5 Chapter 5: Risk Management, Insurance & Surety Bonds
Section 5.1: Commercial General Liability & Workers' Compensation Insurance Section 5.2: Surety Bonds vs. Insurance (Bid, Performance & Payment Bonds) Section 5.3: Risk Assessment, Subcontractor Certificates & Indemnification
6 Chapter 6: Jobsite Safety & Minnesota OSHA Compliance
6.1 MN OSHA Regulations, Inspections & Employer Rights 6.2 Fall Protection, Scaffolding & Personal Protective Equipment 6.3 Trenching, Excavation, Hazard Communication & Silica Standards
7 Chapter 7: Minnesota State Building Code Administration & Permits
7.1 MN Rules Chapter 1300 (Administration, Permits & Plan Review) 7.2 Building Inspections, Code Violations & Certificates of Occupancy 7.4 Building Planning: Means of Egress, Stairways, Exit Doors & Garage Separation 7.5 Life Safety: Smoke Alarms, Safety Glazing, Natural Light, Ceiling Heights & Replacement Windows 7.3 Site Preparation, Surveying & Soil Bearing Capacity
8 Chapter 8: Foundations, Footings, Concrete & Masonry
8.1 Frost Depth Requirements, Soils & Footing Design 8.2 Foundation Wall Systems, Waterproofing & Damp-Proofing 8.3 Concrete Specifications, Reinforcement & Cold-Weather Concreting
9 Chapter 9: Wood Framing, Structural Systems & Load Requirements
9.1 Floor Systems, Girders & Joist Spanning 9.2 Wall Framing, Shear Walls & Structural Headers 9.3 Roof Framing, Trusses, Snow Load & Wind Load Design 9.4 Decks, Balconies, Stairs, Decay Protection & Wood Foundations
10 Chapter 10: Building Enclosure, Energy Code & Environmental Systems
10.1 Roofing Underlayment, Ice Dam Protection & Flashing Details 10.2 Insulation (R-Values), Vapor Retarders & MN Energy Code (Chapter 1322) 10.3 Radon Control Measures (Chapter 1303) & Indoor Air Quality 10.4 Exterior Finishes: House Wrap, Flashing, Siding, Stucco & Brick Veneer 10.5 Foam Plastic Insulation & Interior Finishes (Drywall) 10.6 Roof Covering Materials: Asphalt, Rolled Roofing & Wood Shingles/Shakes 10.7 Associated Issues: Electrical & Plumbing Awareness for Builders
10.6 Roof Covering Materials: Asphalt, Rolled Roofing & Wood Shingles/Shakes
Key Takeaways Explain This Topic AI
Asphalt shingles require a minimum 4:12 slope for single-layer underlayment, or 2:12 with double-layer underlayment; slopes under 2:12 prohibit asphalt shingles entirely.
Standard asphalt shingle fastening is four nails per shingle, increasing to a six-nail pattern in Minnesota's higher wind-exposure areas per manufacturer instructions.
Rolled roofing has a minimum 1:12 slope and is limited in practice to low-slope accessory roofs, not primary dwelling roof coverings.
Wood shingles and shakes require a minimum 3:12 slope, offset course joints, felt interlayment for shakes, and open valley construction with metal flashing.
Minnesota's 24-inch ice barrier membrane requirement at eaves applies to asphalt shingle and wood shingle/shake roofs alike, independent of the covering material chosen.
Last updated: July 2026
Roof Covering Materials: Asphalt, Rolled Roofing & Wood Shingles/Shakes
Beyond underlayment and flashing (covered in Section 10.1), the exam separately tests the roof covering material itself — the slope limits, fastening schedules, and application details specific to asphalt shingles, rolled roofing, and wood shingles/shakes under the Minnesota Residential Code (MN Rules Chapter 1309 / IRC Chapter 9).
1. Asphalt Shingles (IRC R905.2)
Asphalt shingles remain the dominant residential roof covering in Minnesota, but their use is governed by strict slope thresholds:
- Roof Slope Asphalt Shingle Status
- Less than 2:12 Prohibited — requires a low-slope membrane system (TPO, EPDM, modified bitumen)
- 2:12 up to less than 4:12 Permitted, but requires double-layer underlayment (see Section 10.1)
- 4:12 or greater Permitted with standard single-layer underlayment
Fastening: Each shingle requires a minimum of four nails , driven flush and positioned per the manufacturer's nailing pattern (typically just above the cutout slots). In Minnesota's higher wind-exposure areas, or wherever the manufacturer's listing calls for it, the schedule increases to a six-nail pattern per shingle . Nails must penetrate through the shingle and underlayment and at least 3/4 inch into the roof sheathing, or completely through sheathing thinner than 3/4 inch.
Starter course and ridge: A starter strip — either a factory starter product or field-cut shingles with tabs removed — is installed at the eave with sealant strip facing up and out, so the first full course bonds to it and its own tabs are shielded from wind uplift. Hip and ridge caps use manufacturer-specified ridge shingles fastened with two nails each, lapped so no fastener is exposed.
Ice barrier recall: Because Minnesota has a documented history of ice damming statewide, an ice barrier membrane is required at eaves on steep-slope roof coverings (asphalt shingles, wood shingles/shakes), extending from the eave edge to a point at least 24 inches inside the interior line of the exterior wall — this is the same rule covered in Section 10.1 and it applies regardless of which shingle material is used above it.
2. Rolled Roofing (IRC R905.4)
Rolled roofing is a mineral-surfaced asphalt roll product used mainly on low-slope accessory structures — porch roofs, shed roofs, and other secondary roof areas — rather than as a primary dwelling roof covering.
Minimum slope: 1:12, applied with exposed-nail or concealed-nail construction depending on the specific product and manufacturer instructions.
Application limitations: Because rolled roofing has a shorter service life and lower wind and hail resistance than shingles, its use is generally limited to low-visibility, low-slope accessory areas rather than the main roof plane of a dwelling. It is not an acceptable substitute for asphalt shingles on slopes suited to shingle installation.
Double-coverage option: Where a slightly longer service life is needed on a qualifying low-slope area, rolled roofing can be installed with double coverage (each course overlapping more than half its width), which improves water-shedding performance compared with single-coverage exposed-nail application, though it still does not extend rolled roofing's use onto primary steep-slope roof planes.
3. Wood Shingles and Shakes (IRC R905.7 / R905.8)
Wood shingles and shakes are a traditional, higher-maintenance roof covering still specified on some Minnesota homes for appearance, and the exam tests their distinct slope and spacing rules separately from asphalt shingles.
- Requirement Wood Shingles Wood Shakes
- Minimum slope 3:12 3:12
Underlayment Breather-type or felt per manufacturer Felt interlayment (typically 18-inch-wide strip) woven between courses
Exposure/spacing Side lap joints offset a minimum of 1-1/2 inches from the course below Same offset principle; shakes are thicker and split, requiring wider joints for expansion
Ice barrier Required at eaves per the statewide ice-dam rule Required at eaves per the statewide ice-dam rule
Spacing for expansion: Wood shingles and shakes must be installed with a small gap between adjacent pieces in the same course (typically 1/4 to 3/8 inch depending on the wood's moisture content at installation) to allow for seasonal swelling; joints between courses must be offset so no two consecutive courses share a common joint line, which prevents a direct water path through the assembly.
Valleys: Wood shingle and shake roofs require open valley construction with a metal valley flashing (minimum 26-gauge corrosion-resistant metal), because the closed/woven valley techniques used with flexible asphalt shingles do not work with rigid wood pieces. The flashing must extend a minimum distance up each side of the valley centerline, and shingles/shakes are trimmed to the valley line rather than woven across it.
Cross-reference to ice barrier and underlayment: Both the eave ice barrier membrane and the general underlayment requirements are detailed fully in Section 10.1 (Roofing Underlayment, Ice Dam Protection & Flashing Details); this section focuses on the covering material itself, but a contractor should remember the two topics are inspected together — a correctly slotted wood shake roof with no ice barrier underneath still fails inspection in Minnesota's climate.
4. Quick Comparison for the Exam
- Material Min. Slope Key Fastening/Application Note
- Asphalt shingles 4:12 (single layer); 2:12 (double layer) 4 nails/shingle standard, 6 nails in high-wind areas
- Rolled roofing 1:12 Low-slope accessory roofs only, not a primary dwelling covering
- Wood shingles/shakes 3:12 Offset joints, felt interlayment for shakes, open valley metal flashing