Study guide
9.4 Decks, Balconies, Stairs, Decay Protection & Wood Foundations
Minnesota General Contractor Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Minnesota Licensing Statutes & DLI Regulatory Framework
1.1 Scope of Practice, License Types & DLI Administration 1.2 Qualifying Person Requirements & Continuing Education 1.3 Exemptions, Prohibited Acts & DLI Enforcement
2 Chapter 2: Minnesota Contract Law & Statutory Home Warranties
2.1 Essential Terms of Construction Contracts & Change Orders 2.2 Statutory Warranties under Minn. Stat. Chapter 327A 2.3 Insurance Deductible Rebates & Contractor Recovery Fund
3 Chapter 3: Minnesota Mechanics Lien Law (Minn. Stat. Chapter 514)
Section 3.1: Pre-Lien Notice Requirements for Prime & Subcontractors Section 3.2: Recording Mechanics Liens & The 120-Day Filing Deadline Section 3.3: Foreclosure Actions, Priority & Lien Waivers
4 Chapter 4: Business Management, Accounting & Taxes
4.1 Financial Statements, Cash vs. Accrual Accounting & Cash Flow 4.2 Minnesota Business Structures, State Taxes & Capital Improvements 4.3 Payroll Management, Prevailing Wage & Employer Tax Obligations
5 Chapter 5: Risk Management, Insurance & Surety Bonds
Section 5.1: Commercial General Liability & Workers' Compensation Insurance Section 5.2: Surety Bonds vs. Insurance (Bid, Performance & Payment Bonds) Section 5.3: Risk Assessment, Subcontractor Certificates & Indemnification
6 Chapter 6: Jobsite Safety & Minnesota OSHA Compliance
6.1 MN OSHA Regulations, Inspections & Employer Rights 6.2 Fall Protection, Scaffolding & Personal Protective Equipment 6.3 Trenching, Excavation, Hazard Communication & Silica Standards
7 Chapter 7: Minnesota State Building Code Administration & Permits
7.1 MN Rules Chapter 1300 (Administration, Permits & Plan Review) 7.2 Building Inspections, Code Violations & Certificates of Occupancy 7.4 Building Planning: Means of Egress, Stairways, Exit Doors & Garage Separation 7.5 Life Safety: Smoke Alarms, Safety Glazing, Natural Light, Ceiling Heights & Replacement Windows 7.3 Site Preparation, Surveying & Soil Bearing Capacity
8 Chapter 8: Foundations, Footings, Concrete & Masonry
8.1 Frost Depth Requirements, Soils & Footing Design 8.2 Foundation Wall Systems, Waterproofing & Damp-Proofing 8.3 Concrete Specifications, Reinforcement & Cold-Weather Concreting
9 Chapter 9: Wood Framing, Structural Systems & Load Requirements
9.1 Floor Systems, Girders & Joist Spanning 9.2 Wall Framing, Shear Walls & Structural Headers 9.3 Roof Framing, Trusses, Snow Load & Wind Load Design 9.4 Decks, Balconies, Stairs, Decay Protection & Wood Foundations
10 Chapter 10: Building Enclosure, Energy Code & Environmental Systems
10.1 Roofing Underlayment, Ice Dam Protection & Flashing Details 10.2 Insulation (R-Values), Vapor Retarders & MN Energy Code (Chapter 1322) 10.3 Radon Control Measures (Chapter 1303) & Indoor Air Quality 10.4 Exterior Finishes: House Wrap, Flashing, Siding, Stucco & Brick Veneer 10.5 Foam Plastic Insulation & Interior Finishes (Drywall) 10.6 Roof Covering Materials: Asphalt, Rolled Roofing & Wood Shingles/Shakes 10.7 Associated Issues: Electrical & Plumbing Awareness for Builders
9.4 Decks, Balconies, Stairs, Decay Protection & Wood Foundations
Key Takeaways Explain This Topic AI
Wood sill plates on concrete/masonry in contact with earth, and posts embedded in concrete exposed to ground or weather, must be naturally durable or preservative-treated wood under IRC R317 as adopted by Minnesota Rules Chapter 1309.
Ground-contact preservative-treated lumber must be fastened with hot-dipped galvanized (ASTM A153) or stainless-steel hardware because modern copper-based preservatives corrode standard electroplated steel fasteners.
Straight-run stairways are limited to a 7-3/4 inch maximum riser height and a 10-inch minimum tread depth, with no more than 3/8 inch of variance across any single flight.
Attached decks require a minimum of two lateral load connectors rated at 1,500 pounds each (IRC R507.9.2), corrosion-resistant ledger flashing, and post footings extending below the local frost depth.
Guards are required whenever a deck, balcony, or stair walking surface is more than 30 inches above grade, with a minimum 36-inch height and openings that block a 4-inch sphere.
Last updated: July 2026
Decks, Balconies, Stairs, Decay Protection & Wood Foundations
Minnesota's freeze-thaw cycles, seasonal ground moisture, and heavy snow loads make wood decay protection one of the highest-stakes carpentry topics on the licensing exam. The Minnesota Residential Code (MN Rules Chapter 1309 / IRC) requires naturally durable or preservative-treated wood at every location where framing members are exposed to ground contact, concrete contact, or persistent moisture, and it layers additional prescriptive rules onto stairs, decks, and below-grade wood foundation systems.
1. Protection Against Decay (IRC R317)
Wood framing members must be naturally durable wood (heartwood of redwood, cedar, black locust, or similar decay-resistant species) or preservative-treated wood rated for the exposure condition whenever they occur at any of the following locations:
Location Requirement
Wood sill plates on a concrete or masonry foundation in direct contact with earth Preservative-treated or naturally durable
Wood girders entering masonry/concrete walls with less than 1/2 inch clearance on top, sides, and end Preservative-treated or naturally durable
Floor joists or girders closer than 18 inches, or wood siding/sheathing closer than 6 inches, to exposed earth in a crawl space Preservative-treated or naturally durable
Posts or columns supporting permanent structures, embedded in concrete/masonry in contact with the ground, or embedded in concrete exposed to weather Preservative-treated or naturally durable
Wood structural members supporting a permanent structure where the member rests on an exterior concrete slab (walkway, patio) less than 8 inches from grade Preservative-treated or naturally durable
A contractor must also know the fastener rule : modern preservative treatments (ACQ, copper azole) contain far more copper than the older CCA formula, which dramatically accelerates galvanic corrosion of ordinary electroplated steel fasteners and connectors. Ground-contact and exterior preservative-treated lumber must be fastened with hot-dipped galvanized (ASTM A153) or stainless-steel nails, bolts, and structural connectors. Any field-cut end of pressure-treated lumber that exposes untreated wood below the treated shell must be re-treated on site with an approved copper naphthenate solution before it is placed in service.
2. Stairs — Carpentry Geometry Recall
Stair geometry is a recurring exam trap because the numbers are close together and easy to transpose. Baseline dimensional requirements adopted under Minnesota Rules Chapter 1309 for a straight-run stairway serving a one- or two-family dwelling:
Maximum riser height: 7-3/4 inches; the greatest riser within any flight cannot exceed the smallest by more than 3/8 inch.
Minimum tread depth: 10 inches (measured horizontally, nose to nose), with a matching 3/8-inch maximum variance rule across the flight.
Minimum headroom: 6 feet 8 inches, measured vertically from the sloped plane connecting the tread nosings.
Minimum stairway width: 36 inches clear above the permitted handrail height.
Handrail height: 34 to 38 inches above the tread nosing, with a continuous, graspable profile on at least one side of any stairway with four or more risers.
Winder treads: permitted with a minimum tread depth of 10 inches measured 12 inches from the narrow edge, and not less than 6 inches at the narrow end.
Every landing at the top and bottom of a stairway must have a dimension, measured in the direction of travel, at least equal to the stairway's width.
3. Decks and Balconies (IRC R507)
Deck ledger failure is the leading cause of deck collapse, which is why the code carries a detailed prescriptive package for attached decks:
Ledger attachment: The ledger board must bear directly on the dwelling's structural band or rim joist — never on cantilevered floor joists, brick veneer, stucco, or exterior insulation finish systems. Attachment is made with 1/2-inch lag screws or through-bolts, staggered in two rows at spacing set by prescriptive tables tied to joist span and ledger/band-joist thickness, with minimum edge and end distances.
Flashing: Corrosion-resistant flashing must be installed between the ledger and the exterior wall sheathing to shed water away from the connection — trapped moisture at an unflashed ledger is the leading cause of band-joist rot preceding a collapse.
Lateral load connectors: Under IRC R507.9.2, an attached deck must include a minimum of two lateral load connectors, each rated for at least 1,500 pounds , unless an engineered hold-down design is substituted. These devices resist the deck pulling straight away from the house — a distinct failure mode from vertical ledger pull-through.
Footings and frost depth: Deck posts, whether supporting an attached or a freestanding deck, require footings that bear below the jurisdiction's frost depth, identical to the standard applied to the dwelling's own foundation. In the Twin Cities metro area this is commonly 42 inches, with northern Minnesota counties often requiring deeper footings under local amendments; an accessory deck footing gets no frost-depth shortcut.
Guards: A guard is required wherever a walking surface (deck, balcony, porch, or stair) is more than 30 inches above grade or the floor below , measured at any point within 36 inches horizontally of the edge. Guard height must be at least 36 inches for one- and two-family dwellings, and openings must be small enough that a 4-inch sphere cannot pass through (a 6-inch sphere is allowed at triangular openings formed by stair stringers and risers).
4. Chimneys and Chases — Fireblocking Note
Wood-framed chimney chases and any wood framing surrounding a chimney require fireblocking at floor and ceiling levels within the concealed space, and wherever the chase penetrates a floor/ceiling assembly, so a concealed vertical shaft cannot act as a chimney for fire spread. Combustible framing must maintain a minimum 2-inch air clearance to a masonry chimney unless a listed factory-built chimney's own labeling specifies otherwise — contractors should always check the listing label rather than assume a single universal clearance.
5. Permanent Wood Foundations (PWF)
Minnesota recognizes the Permanent Wood Foundation (PWF) as an alternative below-grade foundation system, engineered under the APA/American Wood Council Permanent Wood Foundation Design Manual rather than under the standard concrete/masonry footing provisions.
Key requirements a builder must confirm before construction:
Design documents: PWF construction requires project-specific design documents identifying lumber species, grade, and preservative retention, because PWF-rated treatment carries a higher retention level than standard ground-contact lumber and must be certified as such.
Gravel drainage layer: The footing plate bears on a minimum 4-inch layer of clean gravel or crushed stone that provides positive drainage, extending beyond the foundation footprint to daylight or a sump — this layer functions in place of a concrete footing.
Polyethylene damp-proofing: A 6-mil polyethylene sheet is applied to the exterior of the below-grade wall, lapped and sealed at every seam, replacing the bituminous damp-proofing used on concrete foundation walls.
Framing as insulation cavity: Because the wall studs are both structural and the insulation cavity, vapor retarder placement must be coordinated carefully with Minnesota's Climate Zone 6/7 energy code requirements to avoid trapping moisture inside the wall assembly.