Study guide
1.3 Certification Renewal, Continuing Education & Compliance
Missouri Water and Wastewater Operator Certification Study Guide Exam
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: Missouri State Laws, Regulations & Operator Certification
1.1 MoDNR Regulatory Framework & Operator Classification 1.2 Operator Certification, Experience Requirements & Reciprocity 1.3 Certification Renewal, Continuing Education & Compliance 1.4 Federal & State Drinking Water & Clean Water Acts 1.5 Missouri Design Standards, Construction Permits & the Design Guides 1.6 Utility Management, Administration & Recordkeeping
2 Chapter 2: Water Sources, Hydrology & Raw Water Quality
2.1 Hydrologic Cycle, Groundwater & Surface Water Sources 2.2 Well Construction, Sanitary Protection & Groundwater Hydraulics 2.3 Physical, Chemical & Biological Characteristics of Raw Water 2.4 Water Chemistry Fundamentals for Operators
3 Chapter 3: Coagulation, Flocculation & Sedimentation Processes
3.1 Coagulation Principles & Chemical Additives 3.2 Flocculation Hydraulics & Floc Formation 3.3 Sedimentation Basin Design, Clarifiers & Solids Separation 3.4 Aeration, Taste & Odor Control 3.5 Jar Testing Procedure & Chemical Feed Equipment
4 Chapter 4: Granular Media Filtration & Membrane Technologies
4.1 Conventional Rapid Sand & Dual/Multi-Media Filtration 4.2 Filter Operations, Backwashing & Turbidity Optimization 4.3 Membrane Filtration: Microfiltration, Ultrafiltration, Nanofiltration & Reverse Osmosis
5 Chapter 5: Water Disinfection & Chemical Handling Safety
5.1 Chlorination Chemistry, Breakpoint & Residual Monitoring 5.2 Alternative Disinfectants: Chloramines, Chlorine Dioxide, Ozone & UV 5.3 Disinfection Byproducts & Regulatory Compliance 5.4 Chlorine Gas Safety, Storage & Emergency Containment 5.5 CT Values, Contact Time & Log Inactivation Compliance 5.6 Wastewater Effluent Disinfection & Dechlorination
6 Chapter 6: Softening, Stabilization, Iron/Manganese Removal & Fluoridation
6.1 Lime-Soda Ash Softening & Ion Exchange Demineralization 6.2 Iron and Manganese Removal Technologies 6.3 Corrosion Control, Lead & Copper Rule & Stabilization 6.4 Fluoridation Chemistry, Feed Equipment & Safety
7 Chapter 7: Water Distribution Systems & Infrastructure Operations
7.1 Distribution Piping, Main Installation & Appurtenances 7.2 Distribution Storage Facilities & Pressure Management 7.3 Valves, Fire Hydrants & Metering Systems 7.4 Cross-Connection Control & Backflow Prevention
8 Chapter 8: Wastewater Characteristics, Preliminary & Primary Treatment
8.1 Wastewater Characteristics, Flow Variations & Sampling 8.2 Preliminary Treatment: Screening, Grinding & Grit Removal 8.3 Primary Clarification & Sedimentation Operations
9 Chapter 9: Biological Wastewater Treatment & Secondary Processes
9.1 Activated Sludge Fundamentals & Microbiology 9.2 Activated Sludge Process Control & Operational Parameters 9.3 Activated Sludge Variations: Extended Aeration, Oxidation Ditches & SBRs 9.4 Fixed-Film Processes & Waste Stabilization Ponds
10 Chapter 10: Advanced Wastewater Treatment, Nutrient Removal & Sludge Management
10.1 Biological & Chemical Phosphorus Removal 10.2 Biological Nitrogen Removal: Nitrification & Denitrification 10.3 Sludge Thickening, Stabilization & Digestion 10.4 Biosolids Dewatering, Land Application & 40 CFR Part 503 10.5 Thermal Solids Reduction & Sewage Sludge Incineration
11 Chapter 11: Wastewater Collection Systems & Lift Station Maintenance
11.1 Gravity Sewer Design, Hydraulics & Inflow/Infiltration 11.2 Lift Stations, Pumps & Level Control Systems 11.3 Collection System Operation, Cleaning & Inspection
12 Chapter 12: Water & Wastewater Laboratory Methods, Process Math & Safety
12.1 Water & Wastewater Laboratory Procedures & QA/QC 12.2 Applied Math: Pounds Formula, Chemical Feed & Flow Conversions 12.3 Applied Math: Process Loading, Weir Rates, SVI & Sludge Age 12.4 Plant Safety, Confined Space Entry, Chemical Hazards & Emergency Protocols 12.5 Pumps, Motors, Electrical Controls & Flow Measurement
1.3 Certification Renewal, Continuing Education & Compliance
Key Takeaways Explain This Topic AI
Missouri operator certificates are renewed at least every three years, and the department mails a renewal notice at least 60 days before expiration, but non-receipt does not excuse a late renewal.
Drinking water renewal training is set by level in 10 CSR 60-14 Table 4: 30 hours for A, B, C and DS-III; 20 hours for D and DS-II; 10 hours for DS-I. Wastewater requires 30 hours at every level.
No more than one-half of the required renewal hours may come from safety, supervisory, management, administration, financial or general computer courses.
A certificate not renewed within two months after expiration is lapsed, and a lapsed certificate requires a new application and re-examination rather than a late payment.
Late renewal costs $37.50 per month up to $75 for drinking water certificates and $10 per month up to $20 for wastewater certificates.
Last updated: September 2026
Operator certification in Missouri is not a lifetime credential; it is a professional license that requires continuous renewal and ongoing education. To protect public health and the environment, 10 CSR 60-14 and 10 CSR 20-9 mandate that operators stay current with advancing technology, emerging contaminants, process optimizations, and evolving state and federal environmental regulations.
The Three-Year Renewal Cycle
All Missouri drinking water treatment (Levels A–D), distribution (DS-I to DS-III) and wastewater treatment (Levels A–D) certificates are renewed at least every three (3) years , unless the department prorates a cycle to align multiple certificates.
The department sends a renewal notice to the operator's last known address at least sixty (60) days before expiration . Critically, failure of the department to send that notice does not relieve the operator of the responsibility for renewing.
An individual is not certified while holding an expired certificate. There is no informal "still working on it" status.
The operator must apply for renewal on the department's form, before the certificate lapses , and submit the associated fee for each certificate held.
Operators must notify the department in writing of any change of address, name, telephone number or employer; email and fax are acceptable written communication for this purpose.
Renewals, training histories and contact updates are handled through MoDNR's Operator Certification Information System at apps5.mo.gov/operator, which also hosts the public operator search.
Renewal Training Hours Are Not the Same for Every Certificate
This is the single most misquoted fact in Missouri operator certification. Drinking water renewal training requirements are set by certificate level in 10 CSR 60-14.020, Table 4 — they are not a flat 30 hours:
- Certification level Minimum training required per renewal cycle
- A 30 hours
- B 30 hours
- C 30 hours
- D 20 hours
- DS-III 30 hours
- DS-II 20 hours
- DS-I 10 hours
Wastewater is different again: under 10 CSR 20-9 , the applicant must obtain thirty (30) hours of approved renewal training, without the level-by-level reduction the drinking water table applies.
So a DS-I operator needs 10 hours, a Drinking Water D or DS-II operator needs 20 , and everyone else needs 30 . An operator holding both a Wastewater C and a DS-I certificate must satisfy both requirements separately.
What counts, and the one-half rule
Only training related to water system operations and maintenance, treatment facilities or distribution systems, and approved by the department, receives credit. Training requirements are based on the level of certification held, and training should include an update on new regulation requirements.
Not more than one-half (1/2) of the total renewal training hours required in a renewal period may be credited from safety, supervisory, management, administration, financial and general computer courses. A DS-III operator needing 30 hours can therefore count at most 15 hours from that category.
Credit is based on actual contact time. Breaks and meal times must be shown on the agenda and are not counted.
For multi-day courses , 80% attendance of the course hours is required for credit.
Training providers must submit course details to the department for approval at least thirty (30) days before the training, and must submit the attendance roster afterwards; no credit is issued until the department issues a course identification number.
Acceptable subjects include regulations, operations, maintenance, construction, testing, record keeping and repair of pumps, control valves, altitude valves, fire hydrants, chlorinators, chemical feeders, elevated tanks, standpipes, reservoirs, pressure tanks, filters, backflow devices, meters, control systems and standby generators; process control of aeration, rapid mix, flocculation, sedimentation, filtration, disinfection, chemical oxidation, chemical precipitation, pH adjustment, stabilization, fluoridation, adsorption, ion exchange, reverse osmosis, sludge handling, sequestration and corrosion control; mathematics, chemistry, geology, hydrology, limnology, meteorology, microbiology, hydraulics, cartography and epidemiology; sampling and laboratory technique; safety practices including CPR, first aid, confined space entry, shoring and trenching, hazardous materials handling, electrical safety, traffic control, SCBA, chlorine repair kits and tower climbing; flushing programs, system disinfection, main repair, pressure testing, fire flow measurement, leak detection, tower inspection, draw-down testing and loss/leakage calculations; and computer classes intended for water utilities such as SCADA.
Unacceptable subjects are listed explicitly: introduction to English, history, welding, small motor repair, lawnmower safety and commercial driver's licence training.
Expiration, the Two-Month Window, and Lapse
Missouri's grace window is short and specific. Under 10 CSR 60-14.020(8)(F) :
Any certificate not renewed within the two (2) months following the expiration date will be considered lapsed.
An operator with a lapsed certificate cannot simply pay a late fee — they must submit a new application and re-examine .
Stage Status
Before expiration, complete application filed Certificate renewed; if the department cannot issue the replacement in time through no fault of the operator, the current certificate stays valid until the department acts
- Expiration date passes Not certified. Cannot legally serve as chief operator or make process control decisions
- Within 2 months after expiration Renewable on payment of the renewal fee plus a late fee
- More than 2 months after expiration Lapsed — new application and re-examination required
Late fees: drinking water certificates are charged $37.50 per month up to a total of $75 ; wastewater certificates are charged $10 per month up to a total of $20 .
Suspension adds a wrinkle: if a suspended certificate falls due for renewal during the suspension, the operator must still submit the renewal application and fee before the expiration date, and the department holds the renewed certificate until the suspension ends.
Compliance, Enforcement and Falsification
The department may suspend or revoke a certificate for fraud or deceit in obtaining certification , or for wilful violation of any provision of 10 CSR 60 , with the severity of action based on the frequency and severity of the conduct. Grounds specifically named include misleading or lying to a government official, sample tampering or selective sampling , and falsification. Notice of suspension or revocation is delivered by hand or certified mail and must state the reasons; appeals go to the Administrative Hearing Commission under section 621.250, RSMo.
Falsifying chlorine residual data, laboratory bench sheets, Monthly Operating Reports or Discharge Monitoring Reports is not merely an administrative matter — knowing falsification of records required under the Safe Drinking Water Act or Clean Water Act carries federal criminal exposure in addition to state revocation and civil penalties.