Study guide

12.3 Applied Math: Process Loading, Weir Rates, SVI & Sludge Age

Missouri Water and Wastewater Operator Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Missouri State Laws, Regulations & Operator Certification

1.1 MoDNR Regulatory Framework & Operator Classification 1.2 Operator Certification, Experience Requirements & Reciprocity 1.3 Certification Renewal, Continuing Education & Compliance 1.4 Federal & State Drinking Water & Clean Water Acts 1.5 Missouri Design Standards, Construction Permits & the Design Guides 1.6 Utility Management, Administration & Recordkeeping

2 Chapter 2: Water Sources, Hydrology & Raw Water Quality

2.1 Hydrologic Cycle, Groundwater & Surface Water Sources 2.2 Well Construction, Sanitary Protection & Groundwater Hydraulics 2.3 Physical, Chemical & Biological Characteristics of Raw Water 2.4 Water Chemistry Fundamentals for Operators

3 Chapter 3: Coagulation, Flocculation & Sedimentation Processes

3.1 Coagulation Principles & Chemical Additives 3.2 Flocculation Hydraulics & Floc Formation 3.3 Sedimentation Basin Design, Clarifiers & Solids Separation 3.4 Aeration, Taste & Odor Control 3.5 Jar Testing Procedure & Chemical Feed Equipment

4 Chapter 4: Granular Media Filtration & Membrane Technologies

4.1 Conventional Rapid Sand & Dual/Multi-Media Filtration 4.2 Filter Operations, Backwashing & Turbidity Optimization 4.3 Membrane Filtration: Microfiltration, Ultrafiltration, Nanofiltration & Reverse Osmosis

5 Chapter 5: Water Disinfection & Chemical Handling Safety

5.1 Chlorination Chemistry, Breakpoint & Residual Monitoring 5.2 Alternative Disinfectants: Chloramines, Chlorine Dioxide, Ozone & UV 5.3 Disinfection Byproducts & Regulatory Compliance 5.4 Chlorine Gas Safety, Storage & Emergency Containment 5.5 CT Values, Contact Time & Log Inactivation Compliance 5.6 Wastewater Effluent Disinfection & Dechlorination

6 Chapter 6: Softening, Stabilization, Iron/Manganese Removal & Fluoridation

6.1 Lime-Soda Ash Softening & Ion Exchange Demineralization 6.2 Iron and Manganese Removal Technologies 6.3 Corrosion Control, Lead & Copper Rule & Stabilization 6.4 Fluoridation Chemistry, Feed Equipment & Safety

7 Chapter 7: Water Distribution Systems & Infrastructure Operations

7.1 Distribution Piping, Main Installation & Appurtenances 7.2 Distribution Storage Facilities & Pressure Management 7.3 Valves, Fire Hydrants & Metering Systems 7.4 Cross-Connection Control & Backflow Prevention

8 Chapter 8: Wastewater Characteristics, Preliminary & Primary Treatment

8.1 Wastewater Characteristics, Flow Variations & Sampling 8.2 Preliminary Treatment: Screening, Grinding & Grit Removal 8.3 Primary Clarification & Sedimentation Operations

9 Chapter 9: Biological Wastewater Treatment & Secondary Processes

9.1 Activated Sludge Fundamentals & Microbiology 9.2 Activated Sludge Process Control & Operational Parameters 9.3 Activated Sludge Variations: Extended Aeration, Oxidation Ditches & SBRs 9.4 Fixed-Film Processes & Waste Stabilization Ponds

10 Chapter 10: Advanced Wastewater Treatment, Nutrient Removal & Sludge Management

10.1 Biological & Chemical Phosphorus Removal 10.2 Biological Nitrogen Removal: Nitrification & Denitrification 10.3 Sludge Thickening, Stabilization & Digestion 10.4 Biosolids Dewatering, Land Application & 40 CFR Part 503 10.5 Thermal Solids Reduction & Sewage Sludge Incineration

11 Chapter 11: Wastewater Collection Systems & Lift Station Maintenance

11.1 Gravity Sewer Design, Hydraulics & Inflow/Infiltration 11.2 Lift Stations, Pumps & Level Control Systems 11.3 Collection System Operation, Cleaning & Inspection

12 Chapter 12: Water & Wastewater Laboratory Methods, Process Math & Safety

12.1 Water & Wastewater Laboratory Procedures & QA/QC 12.2 Applied Math: Pounds Formula, Chemical Feed & Flow Conversions 12.3 Applied Math: Process Loading, Weir Rates, SVI & Sludge Age 12.4 Plant Safety, Confined Space Entry, Chemical Hazards & Emergency Protocols 12.5 Pumps, Motors, Electrical Controls & Flow Measurement

12.3 Applied Math: Process Loading, Weir Rates, SVI & Sludge Age

Key Takeaways Explain This Topic AI

Surface Overflow Rate (SOR = Flow gpd / Surface Area sq ft) and Weir Overflow Rate (WOR = Flow gpd / Weir Length ft) control clarifier hydraulic kinetics to prevent solids carryover.

Rapid sand and dual-media filter hydraulic loading is quantified as FLR = Flow (gpm) / Filter Area (sq ft), while backwash rise rate in inches/minute equals gpm/sq ft × 1.604.

Sludge Volume Index (SVI = [SSV30 mL/L × 1,000] / MLSS mg/L) diagnoses settling quality; optimal settling occurs at 80–150 mL/g, while SVI > 150 mL/g signals filamentous bulking.

Food-to-Microorganism ratio (F/M = Influent BOD lbs/day / MLVSS Inventory lbs) and Mean Cell Residence Time (MCRT = Aeration Solids lbs / [WAS lbs/day + Effluent TSS lbs/day]) serve as primary operational levers in activated sludge.

Treatment removal efficiency is calculated as Removal % = [(Influent Concentration - Effluent Concentration) / Influent Concentration] × 100%.

Last updated: September 2026

12.3 Applied Math: Process Loading, Weir Rates, SVI & Sludge Age

Controlling biological, chemical, and physical unit operations in water and wastewater facilities requires rigorous mathematical process control. Operators adjust flow splits, chemical coagulant doses, return activated sludge ( RAS ) rates, and waste activated sludge ( WAS ) volumes based on physical loading rates and biological growth kinetics. Sizing clarifiers, maintaining filter flux rates, optimizing activated sludge floc settling, and balancing microbial food supplies prevent solids carryover and ensure compliance with strict environmental standards.

  • Clarifier Surface Overflow Rate (SOR) & Weir Overflow Rate (WOR)
  • Surface Overflow Rate (SOR)

The Surface Overflow Rate (SOR) (or surface loading rate) measures the upward vertical hydraulic velocity of water leaving a sedimentation basin or secondary clarifier, expressed in gallons per day per square foot ( gpd/sq ft \text{gpd/sq ft} gpd/sq ft ) . For particles to settle by gravity, their settling velocity must exceed the upward liquid overflow velocity: Surface Overflow Rate (SOR, gpd/sq ft) = Influent Flow Rate (gpd) Clarifier Surface Area (sq ft) = Flow (MGD) × 1 , 000 , 000 Surface Area (sq ft) \text{Surface Overflow Rate (SOR, gpd/sq ft)} = \frac{\text{Influent Flow Rate (gpd)}}{\text{Clarifier Surface Area (sq ft)}} = \frac{\text{Flow (MGD)} \times 1,000,000}{\text{Surface Area (sq ft)}} Surface Overflow Rate (SOR, gpd/sq ft) = Clarifier Surface Area (sq ft) Influent Flow Rate (gpd) ​ = Surface Area (sq ft) Flow (MGD) × 1 , 000 , 000 ​

Surface Area Formulas :

Rectangular Basin: Surface Area (sq ft) = Length (ft) × Width (ft) \text{Surface Area (sq ft)} = \text{Length (ft)} \times \text{Width (ft)} Surface Area (sq ft) = Length (ft) × Width (ft)

Circular Clarifier: Surface Area (sq ft) = π × r 2 = 0.7854 × Diameter 2 (ft 2 ) \text{Surface Area (sq ft)} = \pi \times r^2 = 0.7854 \times \text{Diameter}^2\text{ (ft}^2\text{)} Surface Area (sq ft) = π × r 2 = 0.7854 × Diameter 2 (ft 2 )

Typical Design Ranges :

Primary Clarifiers: 800 − 1 , 200 gpd/sq ft 800 - 1,200\text{ gpd/sq ft} 800 − 1 , 200 gpd/sq ft at average design flow

Secondary Clarifiers (Activated Sludge): 400 − 800 gpd/sq ft 400 - 800\text{ gpd/sq ft} 400 − 800 gpd/sq ft ( 1 , 000 − 1 , 200 gpd/sq ft 1,000 - 1,200\text{ gpd/sq ft} 1 , 000 − 1 , 200 gpd/sq ft at peak storm flow)

Weir Overflow Rate (WOR)

The Weir Overflow Rate (WOR) quantifies the volume of clarified effluent discharging over each linear foot of effluent weir crest, expressed in gallons per day per linear foot ( gpd/linear ft \text{gpd/linear ft} gpd/linear ft ) . Excessive weir overflow rates create localized upward velocity currents that pull settling flocs up and over the effluent launders: Weir Overflow Rate (WOR, gpd/linear ft) = Influent Flow Rate (gpd) Total Active Weir Length (ft) \text{Weir Overflow Rate (WOR, gpd/linear ft)} = \frac{\text{Influent Flow Rate (gpd)}}{\text{Total Active Weir Length (ft)}} Weir Overflow Rate (WOR, gpd/linear ft) = Total Active Weir Length (ft) Influent Flow Rate (gpd) ​

Weir Length Calculations :

Rectangular Clarifier: Total end weir length (or perimeter length of internal launder troughs).

Circular Clarifier (Outer Perimeter Weir): Weir Length (ft) = π × Diameter (ft) = 3.1416 × D \text{Weir Length (ft)} = \pi \times \text{Diameter (ft)} = 3.1416 \times D Weir Length (ft) = π × Diameter (ft) = 3.1416 × D

Typical Design Standard : Maximum allowable WOR is generally 10 , 000 − 20 , 000 gpd/linear ft 10,000 - 20,000\text{ gpd/linear ft} 10 , 000 − 20 , 000 gpd/linear ft .

Worked Example 1: Clarifier SOR & WOR Calculation

Problem : A circular secondary clarifier has a diameter of 70 feet 70\text{ feet} 70 feet and is equipped with a peripheral effluent weir along its entire outer perimeter wall. The plant flow rate is 2.8 MGD 2.8\text{ MGD} 2.8 MGD . Calculate:

The Surface Overflow Rate in gpd/sq ft \text{gpd/sq ft} gpd/sq ft ;

The Weir Overflow Rate in gpd/linear ft \text{gpd/linear ft} gpd/linear ft .

Step 1: Calculate clarifier surface area Area (sq ft) = 0.7854 × ( 70 ft ) 2 = 0.7854 × 4 , 900 = 3 , 848.46 sq ft \text{Area (sq ft)} = 0.7854 \times (70\text{ ft})^2 = 0.7854 \times 4,900 = 3,848.46\text{ sq ft} Area (sq ft) = 0.7854 × ( 70 ft ) 2 = 0.7854 × 4 , 900 = 3 , 848.46 sq ft

Step 2: Calculate Surface Overflow Rate (SOR) SOR = 2 , 800 , 000 gpd 3 , 848.46 sq ft = 727.56 gpd/sq ft ≈ 728 gpd/sq ft \text{SOR} = \frac{2,800,000\text{ gpd}}{3,848.46\text{ sq ft}} = 727.56\text{ gpd/sq ft} \approx 728\text{ gpd/sq ft} SOR = 3 , 848.46 sq ft 2 , 800 , 000 gpd ​ = 727.56 gpd/sq ft ≈ 728 gpd/sq ft

Step 3: Calculate total peripheral weir length Weir Length (ft) = 3.1416 × 70 ft = 219.91 ft \text{Weir Length (ft)} = 3.1416 \times 70\text{ ft} = 219.91\text{ ft} Weir Length (ft) = 3.1416 × 70 ft = 219.91 ft

Step 4: Calculate Weir Overflow Rate (WOR) WOR = 2 , 800 , 000 gpd 219.91 ft = 12 , 732.48 gpd/linear ft ≈ 12 , 732 gpd/linear ft \text{WOR} = \frac{2,800,000\text{ gpd}}{219.91\text{ ft}} = 12,732.48\text{ gpd/linear ft} \approx 12,732\text{ gpd/linear ft} WOR = 219.91 ft 2 , 800 , 000 gpd ​ = 12 , 732.48 gpd/linear ft ≈ 12 , 732 gpd/linear ft

Filter Loading Rate (FLR) & Backwash Rise Rate

In granular media filtration (rapid sand or dual-media anthracite/sand filters):

Filter Loading Rate (Hydraulic Flux) Filter Loading Rate (FLR, gpm/sq ft) = Flow Rate (gpm) Filter Surface Area (sq ft) = Flow Rate (gpd) 1 , 440 min/day × Filter Area (sq ft) \text{Filter Loading Rate (FLR, gpm/sq ft)} = \frac{\text{Flow Rate (gpm)}}{\text{Filter Surface Area (sq ft)}} = \frac{\text{Flow Rate (gpd)}}{1,440\text{ min/day} \times \text{Filter Area (sq ft)}} Filter Loading Rate (FLR, gpm/sq ft) = Filter Surface Area (sq ft) Flow Rate (gpm) ​ = 1 , 440 min/day × Filter Area (sq ft) Flow Rate (gpd) ​

Standard rapid sand filtration rate: 2.0 − 4.0 gpm/sq ft 2.0 - 4.0\text{ gpm/sq ft} 2.0 − 4.0 gpm/sq ft ; High-rate dual-media filters: 4.0 − 8.0 gpm/sq ft 4.0 - 8.0\text{ gpm/sq ft} 4.0 − 8.0 gpm/sq ft .

Filter Backwash Rate & Bed Expansion Rise Rate

Backwash flow is expressed in gpm/sq ft \text{gpm/sq ft} gpm/sq ft (typically 15 − 20 gpm/sq ft 15 - 20\text{ gpm/sq ft} 15 − 20 gpm/sq ft ). To convert backwash rate to vertical upward rise rate in inches per minute ( in/min \text{in/min} in/min ) : Backwash Rise Rate (in/min) = Backwash Rate (gpm/sq ft) × 12 in/ft 7.48 gal/cu ft = Backwash Rate (gpm/sq ft) × 1.604 \text{Backwash Rise Rate (in/min)} = \frac{\text{Backwash Rate (gpm/sq ft)} \times 12\text{ in/ft}}{7.48\text{ gal/cu ft}} = \text{Backwash Rate (gpm/sq ft)} \times 1.604 Backwash Rise Rate (in/min) = 7.48 gal/cu ft Backwash Rate (gpm/sq ft) × 12 in/ft ​ = Backwash Rate (gpm/sq ft) × 1.604

Worked Example 2: Filter Hydraulic & Backwash Calculations

Problem : A water plant operates four dual-media filters, each measuring 15 ft 15\text{ ft} 15 ft wide by 20 ft 20\text{ ft} 20 ft long. Total plant flow is 4 , 800 gpm 4,800\text{ gpm} 4 , 800 gpm split equally across all four active filters. During backwash of one filter, the backwash pump delivers 4 , 500 gpm 4,500\text{ gpm} 4 , 500 gpm . Calculate:

  • Filter Loading Rate (FLR) per operating filter in gpm/sq ft \text{gpm/sq ft} gpm/sq ft ;
  • Backwash rate in gpm/sq ft \text{gpm/sq ft} gpm/sq ft ;

Backwash vertical rise rate in inches/minute \text{inches/minute} inches/minute .

Step 1: Calculate surface area of one filter Area = 15 ft × 20 ft = 300 sq ft \text{Area} = 15\text{ ft} \times 20\text{ ft} = 300\text{ sq ft} Area = 15 ft × 20 ft = 300 sq ft

Step 2: Flow per operating filter Flow/filter = 4 , 800 gpm 4 filters = 1 , 200 gpm/filter \text{Flow/filter} = \frac{4,800\text{ gpm}}{4\text{ filters}} = 1,200\text{ gpm/filter} Flow/filter = 4 filters 4 , 800 gpm ​ = 1 , 200 gpm/filter

Step 3: Calculate Filter Loading Rate (FLR) FLR = 1 , 200 gpm 300 sq ft = 4.0 gpm/sq ft \text{FLR} = \frac{1,200\text{ gpm}}{300\text{ sq ft}} = 4.0\text{ gpm/sq ft} FLR = 300 sq ft 1 , 200 gpm ​ = 4.0 gpm/sq ft

Step 4: Calculate Backwash Rate Backwash Rate = 4 , 500 gpm 300 sq ft = 15.0 gpm/sq ft \text{Backwash Rate} = \frac{4,500\text{ gpm}}{300\text{ sq ft}} = 15.0\text{ gpm/sq ft} Backwash Rate = 300 sq ft 4 , 500 gpm ​ = 15.0 gpm/sq ft

Step 5: Calculate Backwash Rise Rate (in/min) Rise Rate = 15.0 gpm/sq ft × 1.604 = 24.06 in/min \text{Rise Rate} = 15.0\text{ gpm/sq ft} \times 1.604 = 24.06\text{ in/min} Rise Rate = 15.0 gpm/sq ft × 1.604 = 24.06 in/min

Sludge Volume Index (SVI) & Settleability

Sludge Volume Index (SVI) is a standard process control metric defining the volume in milliliters occupied by 1.0 gram 1.0\text{ gram} 1.0 gram of mixed liquor suspended solids after 30 minutes 30\text{ minutes} 30 minutes of quiescent settling in a 1.0 -liter 1.0\text{-liter} 1.0 -liter graduated cylinder or settleometer: SVI (mL/g) = Settled Sludge Volume after 30 min (SSV 30 , mL/L) × 1 , 000 Mixed Liquor Suspended Solids (MLSS, mg/L) \text{SVI (mL/g)} = \frac{\text{Settled Sludge Volume after 30 min (SSV}_{30}\text{, mL/L)} \times 1,000}{\text{Mixed Liquor Suspended Solids (MLSS, mg/L)}} SVI (mL/g) = Mixed Liquor Suspended Solids (MLSS, mg/L) Settled Sludge Volume after 30 min (SSV 30 ​ , mL/L) × 1 , 000 ​ +-----------------------------------------------------------------------------------------+

  • | SVI PROCESS DIAGNOSTIC MATRIX |
  • +-----------------------------------------------------------------------------------------+
  • | SVI < 70 mL/g: |
  • | - Rapid-settling, dense, granular pin-point floc. |
  • | - Old sludge age, over-oxidized; generates turbid effluent with straggler pin flocs. |
  • | - Action: Increase WAS rate (lower sludge age) to rejuvenate active biological growth. |
  • +-----------------------------------------------------------------------------------------+
  • | SVI = 80 to 150 mL/g (IDEAL OPERATING RANGE): |
  • | - Excellent settling flocs, uniform compaction, crystal-clear supernatant. |
  • | - Optimal balance of filamentous backbones and floc-forming heterotrophic bacteria. |
  • | - Action: Maintain current operational RAS/WAS equilibrium. |
  • +-----------------------------------------------------------------------------------------+
  • | SVI > 150 to 200+ mL/g: |
  • | - Slow settling, bulky, high blanket, poor compaction. |
  • | - Filamentous bulking (*Microthrix parvicella*, *Nocardia*, Type 021N) or young sludge.|
  • | - Risk of severe solids washout over secondary clarifier weirs. |
  • | - Action: Increase DO, adjust F/M, dose chlorine/hydrogen peroxide to RAS if needed. |
  • +-----------------------------------------------------------------------------------------+
  • Worked Example 3: SVI Calculation

Problem : An operator performs a 30 -minute 30\text{-minute} 30 -minute settleability test on mixed liquor. The settled sludge volume at 30 minutes 30\text{ minutes} 30 minutes is 270 mL/L 270\text{ mL/L} 270 mL/L . Laboratory analysis reveals an MLSS concentration of 2 , 250 mg/L 2,250\text{ mg/L} 2 , 250 mg/L . Calculate SVI.

Step 1: Apply SVI formula SVI (mL/g) = 270 mL/L × 1 , 000 2 , 250 mg/L = 270 , 000 2 , 250 = 120 mL/g \text{SVI (mL/g)} = \frac{270\text{ mL/L} \times 1,000}{2,250\text{ mg/L}} = \frac{270,000}{2,250} = 120\text{ mL/g} SVI (mL/g) = 2 , 250 mg/L 270 mL/L × 1 , 000 ​ = 2 , 250 270 , 000 ​ = 120 mL/g

Step 2: Process Interpretation The SVI of 120 mL/g 120\text{ mL/g} 120 mL/g falls squarely within the ideal range ( 80 − 150 mL/g 80 - 150\text{ mL/g} 80 − 150 mL/g ), indicating excellent settling kinetics and a stable biological floc matrix.

Food-to-Microorganism Ratio (F/M)

The Food-to-Microorganism (F/M) Ratio expresses the daily organic loading (food) applied relative to the active microbial population (microorganisms) maintained under aeration: F/M = Influent BOD 5 Applied (lbs/day) Mixed Liquor Volatile Suspended Solids Under Aeration (lbs MLVSS) \text{F/M} = \frac{\text{Influent BOD}_5\text{ Applied (lbs/day)}}{\text{Mixed Liquor Volatile Suspended Solids Under Aeration (lbs MLVSS)}} F/M = Mixed Liquor Volatile Suspended Solids Under Aeration (lbs MLVSS) Influent BOD 5 ​ Applied (lbs/day) ​ F/M = Influent Flow (MGD) × Influent BOD 5 (mg/L) × 8.34 Aeration Basin Volume (MG) × MLVSS (mg/L) × 8.34 \text{F/M} = \frac{\text{Influent Flow (MGD)} \times \text{Influent BOD}_5\text{ (mg/L)} \times 8.34}{\text{Aeration Basin Volume (MG)} \times \text{MLVSS (mg/L)} \times 8.34} F/M = Aeration Basin Volume (MG) × MLVSS (mg/L) × 8.34 Influent Flow (MGD) × Influent BOD 5 ​ (mg/L) × 8.34 ​

Typical Operating Ranges :

Conventional Activated Sludge: 0.20 − 0.50 lb BOD/lb MLVSS/day 0.20 - 0.50\text{ lb BOD/lb MLVSS/day} 0.20 − 0.50 lb BOD/lb MLVSS/day

Extended Aeration / Oxidation Ditch: 0.05 − 0.15 lb BOD/lb MLVSS/day 0.05 - 0.15\text{ lb BOD/lb MLVSS/day} 0.05 − 0.15 lb BOD/lb MLVSS/day

High-Rate Activated Sludge: 0.50 − 1.00 lb BOD/lb MLVSS/day 0.50 - 1.00\text{ lb BOD/lb MLVSS/day} 0.50 − 1.00 lb BOD/lb MLVSS/day

Worked Example 4: F/M Ratio Calculation

Problem : A wastewater plant treats 3.5 MGD 3.5\text{ MGD} 3.5 MGD with an influent BOD 5 \text{BOD}_5 BOD 5 ​ of 210 mg/L 210\text{ mg/L} 210 mg/L . The total aeration basin volume is 2.0 MG 2.0\text{ MG} 2.0 MG . Laboratory testing indicates an MLSS concentration of 2 , 800 mg/L 2,800\text{ mg/L} 2 , 800 mg/L with a volatile fraction of 75 % 75\% 75% (MLVSS = 2 , 800 × 0.75 = 2 , 100 mg/L = 2,800 \times 0.75 = 2,100\text{ mg/L} = 2 , 800 × 0.75 = 2 , 100 mg/L ). Calculate the operational F/M ratio.

Step 1: Calculate daily food load (lbs BOD/day) Food (lbs BOD/day) = 3.5 MGD × 210 mg/L × 8.34 = 6 , 129.9 lbs/day \text{Food (lbs BOD/day)} = 3.5\text{ MGD} \times 210\text{ mg/L} \times 8.34 = 6,129.9\text{ lbs/day} Food (lbs BOD/day) = 3.5 MGD × 210 mg/L × 8.34 = 6 , 129.9 lbs/day

Step 2: Calculate active biological mass under aeration (lbs MLVSS) Microorganisms (lbs MLVSS) = 2.0 MG × 2 , 100 mg/L × 8.34 = 35 , 028.0 lbs \text{Microorganisms (lbs MLVSS)} = 2.0\text{ MG} \times 2,100\text{ mg/L} \times 8.34 = 35,028.0\text{ lbs} Microorganisms (lbs MLVSS) = 2.0 MG × 2 , 100 mg/L × 8.34 = 35 , 028.0 lbs

Step 3: Calculate F/M ratio F/M = 6 , 129.9 lbs BOD/day 35 , 028.0 lbs MLVSS = 0.175 lb BOD/lb MLVSS/day \text{F/M} = \frac{6,129.9\text{ lbs BOD/day}}{35,028.0\text{ lbs MLVSS}} = 0.175\text{ lb BOD/lb MLVSS/day} F/M = 35 , 028.0 lbs MLVSS 6 , 129.9 lbs BOD/day ​ = 0.175 lb BOD/lb MLVSS/day

Mean Cell Residence Time (MCRT / Sludge Age)

Mean Cell Residence Time (MCRT) (or Solids Retention Time, SRT ) represents the average number of days that biological microorganisms remain within the activated sludge system before being deliberately wasted or inadvertently lost in the final effluent: MCRT (days) = Total Suspended Solids in System (lbs MLSS) TSS Lost per Day (lbs WAS/day + lbs Effluent TSS/day) \text{MCRT (days)} = \frac{\text{Total Suspended Solids in System (lbs MLSS)}}{\text{TSS Lost per Day (lbs WAS/day + lbs Effluent TSS/day)}} MCRT (days) = TSS Lost per Day (lbs WAS/day + lbs Effluent TSS/day) Total Suspended Solids in System (lbs MLSS) ​ MCRT (days) = Aeration Vol (MG) × MLSS (mg/L) × 8.34 [ WAS Flow (MGD) × WAS SS (mg/L) × 8.34 ] + [ Effluent Flow (MGD) × Effluent TSS (mg/L) × 8.34 ] \text{MCRT (days)} = \frac{\text{Aeration Vol (MG)} \times \text{MLSS (mg/L)} \times 8.34}{[\text{WAS Flow (MGD)} \times \text{WAS SS (mg/L)} \times 8.34] + [\text{Effluent Flow (MGD)} \times \text{Effluent TSS (mg/L)} \times 8.34]} MCRT (days) = [ WAS Flow (MGD) × WAS SS (mg/L) × 8.34 ] + [ Effluent Flow (MGD) × Effluent TSS (mg/L) × 8.34 ] Aeration Vol (MG) × MLSS (mg/L) × 8.34 ​

(Note: When clarifier solids inventory is included in calculation: Total System Solids = ( Aeration Vol × MLSS × 8.34 ) + ( Clarifier Vol × Clarifier SS × 8.34 ) \text{Total System Solids} = (\text{Aeration Vol} \times \text{MLSS} \times 8.34) + (\text{Clarifier Vol} \times \text{Clarifier SS} \times 8.34) Total System Solids = ( Aeration Vol × MLSS × 8.34 ) + ( Clarifier Vol × Clarifier SS × 8.34 ) .)

Worked Example 5: MCRT Determination

Problem : An activated sludge facility has an aeration basin volume of 1.5 MG 1.5\text{ MG} 1.5 MG and maintains an MLSS of 2 , 400 mg/L 2,400\text{ mg/L} 2 , 400 mg/L . The operator wastes sludge (WAS) at a rate of 0.035 MGD 0.035\text{ MGD} 0.035 MGD ( 35 , 000 gpd 35,000\text{ gpd} 35 , 000 gpd ) with a WAS concentration of 6 , 500 mg/L 6,500\text{ mg/L} 6 , 500 mg/L . Final effluent flow is 3.0 MGD 3.0\text{ MGD} 3.0 MGD with an effluent TSS of 8.0 mg/L 8.0\text{ mg/L} 8.0 mg/L . Calculate the system MCRT in days.

Step 1: Calculate solids inventory in aeration basin (lbs) Aeration Solids = 1.5 MG × 2 , 400 mg/L × 8.34 = 30 , 024.0 lbs \text{Aeration Solids} = 1.5\text{ MG} \times 2,400\text{ mg/L} \times 8.34 = 30,024.0\text{ lbs} Aeration Solids = 1.5 MG × 2 , 400 mg/L × 8.34 = 30 , 024.0 lbs

Step 2: Calculate daily solids wasted via WAS (lbs/day) WAS Solids = 0.035 MGD × 6 , 500 mg/L × 8.34 = 1 , 897.35 lbs/day \text{WAS Solids} = 0.035\text{ MGD} \times 6,500\text{ mg/L} \times 8.34 = 1,897.35\text{ lbs/day} WAS Solids = 0.035 MGD × 6 , 500 mg/L × 8.34 = 1 , 897.35 lbs/day

Step 3: Calculate daily solids lost in final effluent (lbs/day) Effluent Solids = 3.0 MGD × 8.0 mg/L × 8.34 = 200.16 lbs/day \text{Effluent Solids} = 3.0\text{ MGD} \times 8.0\text{ mg/L} \times 8.34 = 200.16\text{ lbs/day} Effluent Solids = 3.0 MGD × 8.0 mg/L × 8.34 = 200.16 lbs/day

Step 4: Calculate total daily solids removed from system Total Daily Loss = 1 , 897.35 + 200.16 = 2 , 097.51 lbs/day \text{Total Daily Loss} = 1,897.35 + 200.16 = 2,097.51\text{ lbs/day} Total Daily Loss = 1 , 897.35 + 200.16 = 2 , 097.51 lbs/day

Step 5: Calculate MCRT MCRT = 30 , 024.0 lbs 2 , 097.51 lbs/day = 14.314 days ≈ 14.3 days \text{MCRT} = \frac{30,024.0\text{ lbs}}{2,097.51\text{ lbs/day}} = 14.314\text{ days} \approx 14.3\text{ days} MCRT = 2 , 097.51 lbs/day 30 , 024.0 lbs ​ = 14.314 days ≈ 14.3 days

Treatment Removal Efficiency

Permits require tracking unit process and whole-plant removal efficiencies: Removal Efficiency (%) = Influent Concentration (or Load) − Effluent Concentration (or Load) Influent Concentration (or Load) × 100 % \text{Removal Efficiency (\%)} = \frac{\text{Influent Concentration (or Load)} - \text{Effluent Concentration (or Load)}}{\text{Influent Concentration (or Load)}} \times 100\% Removal Efficiency (%) = Influent Concentration (or Load) Influent Concentration (or Load) − Effluent Concentration (or Load) ​ × 100%

Worked Example 6: Plant Removal Efficiency

Problem : Raw influent wastewater contains 280 mg/L BOD 5 280\text{ mg/L BOD}_5 280 mg/L BOD 5 ​ . Final discharge effluent contains 14 mg/L BOD 5 14\text{ mg/L BOD}_5 14 mg/L BOD 5 ​ . Calculate the facility's overall BOD 5 \text{BOD}_5 BOD 5 ​ removal efficiency.

Calculation : Removal Efficiency = 280 mg/L − 14 mg/L 280 mg/L × 100 % = 266 280 × 100 % = 95.0 % \text{Removal Efficiency} = \frac{280\text{ mg/L} - 14\text{ mg/L}}{280\text{ mg/L}} \times 100\% = \frac{266}{280} \times 100\% = 95.0\% Removal Efficiency = 280 mg/L 280 mg/L − 14 mg/L ​ × 100% = 280 266 ​ × 100% = 95.0%

Loading diagram... Activated Sludge Mass Balance & Process Control Dynamic Control Loops