Study guide

3.1 Coagulation Principles & Chemical Additives

Missouri Water and Wastewater Operator Certification Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: Missouri State Laws, Regulations & Operator Certification

1.1 MoDNR Regulatory Framework & Operator Classification 1.2 Operator Certification, Experience Requirements & Reciprocity 1.3 Certification Renewal, Continuing Education & Compliance 1.4 Federal & State Drinking Water & Clean Water Acts 1.5 Missouri Design Standards, Construction Permits & the Design Guides 1.6 Utility Management, Administration & Recordkeeping

2 Chapter 2: Water Sources, Hydrology & Raw Water Quality

2.1 Hydrologic Cycle, Groundwater & Surface Water Sources 2.2 Well Construction, Sanitary Protection & Groundwater Hydraulics 2.3 Physical, Chemical & Biological Characteristics of Raw Water 2.4 Water Chemistry Fundamentals for Operators

3 Chapter 3: Coagulation, Flocculation & Sedimentation Processes

3.1 Coagulation Principles & Chemical Additives 3.2 Flocculation Hydraulics & Floc Formation 3.3 Sedimentation Basin Design, Clarifiers & Solids Separation 3.4 Aeration, Taste & Odor Control 3.5 Jar Testing Procedure & Chemical Feed Equipment

4 Chapter 4: Granular Media Filtration & Membrane Technologies

4.1 Conventional Rapid Sand & Dual/Multi-Media Filtration 4.2 Filter Operations, Backwashing & Turbidity Optimization 4.3 Membrane Filtration: Microfiltration, Ultrafiltration, Nanofiltration & Reverse Osmosis

5 Chapter 5: Water Disinfection & Chemical Handling Safety

5.1 Chlorination Chemistry, Breakpoint & Residual Monitoring 5.2 Alternative Disinfectants: Chloramines, Chlorine Dioxide, Ozone & UV 5.3 Disinfection Byproducts & Regulatory Compliance 5.4 Chlorine Gas Safety, Storage & Emergency Containment 5.5 CT Values, Contact Time & Log Inactivation Compliance 5.6 Wastewater Effluent Disinfection & Dechlorination

6 Chapter 6: Softening, Stabilization, Iron/Manganese Removal & Fluoridation

6.1 Lime-Soda Ash Softening & Ion Exchange Demineralization 6.2 Iron and Manganese Removal Technologies 6.3 Corrosion Control, Lead & Copper Rule & Stabilization 6.4 Fluoridation Chemistry, Feed Equipment & Safety

7 Chapter 7: Water Distribution Systems & Infrastructure Operations

7.1 Distribution Piping, Main Installation & Appurtenances 7.2 Distribution Storage Facilities & Pressure Management 7.3 Valves, Fire Hydrants & Metering Systems 7.4 Cross-Connection Control & Backflow Prevention

8 Chapter 8: Wastewater Characteristics, Preliminary & Primary Treatment

8.1 Wastewater Characteristics, Flow Variations & Sampling 8.2 Preliminary Treatment: Screening, Grinding & Grit Removal 8.3 Primary Clarification & Sedimentation Operations

9 Chapter 9: Biological Wastewater Treatment & Secondary Processes

9.1 Activated Sludge Fundamentals & Microbiology 9.2 Activated Sludge Process Control & Operational Parameters 9.3 Activated Sludge Variations: Extended Aeration, Oxidation Ditches & SBRs 9.4 Fixed-Film Processes & Waste Stabilization Ponds

10 Chapter 10: Advanced Wastewater Treatment, Nutrient Removal & Sludge Management

10.1 Biological & Chemical Phosphorus Removal 10.2 Biological Nitrogen Removal: Nitrification & Denitrification 10.3 Sludge Thickening, Stabilization & Digestion 10.4 Biosolids Dewatering, Land Application & 40 CFR Part 503 10.5 Thermal Solids Reduction & Sewage Sludge Incineration

11 Chapter 11: Wastewater Collection Systems & Lift Station Maintenance

11.1 Gravity Sewer Design, Hydraulics & Inflow/Infiltration 11.2 Lift Stations, Pumps & Level Control Systems 11.3 Collection System Operation, Cleaning & Inspection

12 Chapter 12: Water & Wastewater Laboratory Methods, Process Math & Safety

12.1 Water & Wastewater Laboratory Procedures & QA/QC 12.2 Applied Math: Pounds Formula, Chemical Feed & Flow Conversions 12.3 Applied Math: Process Loading, Weir Rates, SVI & Sludge Age 12.4 Plant Safety, Confined Space Entry, Chemical Hazards & Emergency Protocols 12.5 Pumps, Motors, Electrical Controls & Flow Measurement

3.1 Coagulation Principles & Chemical Additives

Key Takeaways Explain This Topic AI

Colloidal particles in raw water range from 0.001 to 1.0 µm and carry a negative electrical charge, maintaining stability via an electrostatic repulsive barrier measured by zeta potential (-15 to -30 mV).

Primary coagulants destabilize colloids through four distinct mechanisms: double-layer compression, charge neutralization, sweep flocculation (enmeshment), and interparticle bridging.

Commercial aluminum sulfate (alum, Al2(SO4)3·14H2O) consumes approximately 0.50 mg/L of natural alkalinity as CaCO3 for every 1.0 mg/L fed, requiring supplemental base feed if raw water alkalinity is deficient.

Rapid mixing disperses coagulant quickly at the intensity and contact time established by the approved mixer design; in-line devices may mix in seconds, while mechanical basins commonly provide longer contact.

The multi-station jar test is the standard operational laboratory method used to evaluate coagulant dosage, optimum coagulation pH, floc settling rates, and polymer aid effectiveness.

Last updated: September 2026

Colloidal Stability and Surface Physics in Raw Water

Surface water sources contain suspended solids and natural organic matter that create turbidity, color, and microbiological risk. In water treatment engineering, particulate matter is categorized by particle diameter into three distinct classes:

Suspended solids ( > 1.0 μ m > 1.0\text{ }\mu\text{m} > 1.0 μ m ): Coarse silt, fine sand, and large algae that settle readily under quiescent conditions.

Colloidal solids ( 0.001 to 1.0 μ m 0.001\text{ to }1.0\text{ }\mu\text{m} 0.001 to 1.0 μ m ): Clays, colloidal silica, humic and fulvic acids, viruses, and cellular fragments that remain suspended indefinitely in water without chemical treatment.

Dissolved solids ( < 0.001 μ m < 0.001\text{ }\mu\text{m} < 0.001 μ m / dissolved ionic species): Dissolved minerals, salts, and small organic molecules.

The Electrical Double Layer and Zeta Potential

Colloidal stability is governed by surface electrical charges and interparticle forces. Natural colloids in water acquire a net negative surface charge through three primary mechanisms:

Isomorphic substitution : Mineral lattice substitutions (e.g., A l 3 + Al^{3+} A l 3 + replacing S i 4 + Si^{4+} S i 4 + in clay crystal structures).

Ionization of surface functional groups : Dissociation of carboxyl ( − C O O H → − C O O − + H + -COOH \rightarrow -COO^- + H^+ − COO H → − CO O − + H + ) and phenolic hydroxyl groups on organic macromolecules.

Specific ion adsorption : Preferential adsorption of natural anions (such as humic substances or hydroxyl ions) onto particle surfaces.

To balance this negative surface charge, waterborne cations are drawn toward the colloid, establishing an electrical double layer consisting of:

The Stern Layer : A compact, fixed inner boundary of tightly bound, positively charged counter-ions moving synchronously with the particle.

The Gouy-Chapman Diffuse Layer : An outer, dynamic zone where counter-ion concentration gradually decreases outward until reaching the bulk solution ionic equilibrium.

When a colloid moves through water, it carries a boundary layer of water molecules with it. The electrical potential at this shear plane (the slipping plane) is defined as the zeta potential (typically − 15 to − 30 mV -15\text{ to }-30\text{ mV} − 15 to − 30 mV in natural raw surface waters). As long as the zeta potential remains strongly negative, mutual electrostatic repulsion (like charges repelling) prevents colloids from approaching each other. Repulsive Electrostatic Force (Zeta Potential) > Attractive van der Waals Force ---> Stable Suspension (No Settling)

Opposing this repulsion are van der Waals forces —short-range, attractive intermolecular London-dispersion forces. Because van der Waals attraction decays rapidly with distance ( F ∝ 1 / r 6 F \propto 1/r^6 F ∝ 1/ r 6 ), colloids cannot agglomerate unless their electrostatic repulsive barrier is neutralized or compressed, allowing them to approach within nanometer proximity.

Mechanisms of Coagulation

Coagulation is the chemical process of adding specialized metal salts or polymers to destabilize colloidal particles, eliminating the repulsive energy barrier so particles can aggregate. Coagulation occurs through four distinct physical-chemical mechanisms:

Coagulation Mechanism Primary Chemical Regimes Operating Principle & Physical Process

Charge Neutralization Low to moderate coagulant dose; acidic to neutral pH ( 5.5 – 6.5 5.5\text{--}6.5 5.5 – 6.5 ) Highly charged cationic hydrolysis species ( A l 3 + , A l ( O H ) 2 + , A l 8 ( O H ) 20 4 + Al^{3+}, Al(OH)^{2+}, Al_8(OH)_{20}^{4+} A l 3 + , A l ( O H ) 2 + , A l 8 ​ ( O H ) 20 4 + ​ ) adsorb directly onto negative colloidal surfaces, driving the zeta potential to near 0 mV 0\text{ mV} 0 mV (isoelectric point).

Double-Layer Compression High ionic strength / elevated electrolyte concentration Increasing bulk water ionic strength compresses the diffuse layer thickness, collapsing the electrostatic energy barrier and allowing van der Waals forces to dominate.

Sweep Flocculation (Enmeshment) High coagulant dose; neutral to alkaline pH ( 6.8 – 8.0 6.8\text{--}8.0 6.8 – 8.0 ) Massive precipitation of amorphous aluminum hydroxide ( A l ( O H ) 3 ( s ) Al(OH)_3(s) A l ( O H ) 3 ​ ( s ) ) or ferric hydroxide ( F e ( O H ) 3 ( s ) Fe(OH)_3(s) F e ( O H ) 3 ​ ( s ) ) creates a dense, sticky hydroxide precipitate that sweeps through the water, mechanically entrapping colloids. Essential in low-turbidity waters.

Interparticle Bridging Synthetic high-molecular-weight polymers Long-chain polymeric molecules attach simultaneously to multiple colloidal particles via functional groups or hydrogen bonding, forming a physical polymer-colloid matrix.

Important

Restabilization Warning : In charge neutralization, applying an excessive coagulant dose can reverse particle charge from negative to positive (positive zeta potential), re-stabilizing the colloidal dispersion and causing post-treatment turbidity spikes.

Loading diagram... Coagulation Pathways: Charge Neutralization vs. Sweep Flocculation

Primary Coagulants and Alkalinity Stoichiometry

Water treatment plants utilize trivalent metal coagulants ( A l 3 + Al^{3+} A l 3 + and F e 3 + Fe^{3+} F e 3 + ) because the trivalent ion is up to 700 to 1,000 times more effective at colloidal destabilization than monovalent ions ( N a + Na^+ N a + ), a principle known as the Schulze-Hardy Rule .

1. Aluminum Sulfate (Commercial Alum)

Commercial alum is delivered as dry hydrate or liquid solution with the typical chemical formula Al 2 ( SO 4 ) 3 ⋅ 14 H 2 O \text{Al}_2(\text{SO}_4)_3 \cdot 14\text{H}_2\text{O} Al 2 ​ ( SO 4 ​ ) 3 ​ ⋅ 14 H 2 ​ O (molecular weight approximately 594 g/mol 594\text{ g/mol} 594 g/mol ). Liquid alum typically contains approximately 48.5 % dry alum 48.5\%\text{ dry alum} 48.5% dry alum by weight, with a specific gravity of 1.32 to 1.34 1.32\text{ to }1.34 1.32 to 1.34 .

When alum is dosed into water, it reacts with natural bicarbonate alkalinity to form insoluble aluminum hydroxide precipitate: Al 2 ( SO 4 ) 3 ⋅ 14 H 2 O + 3 Ca ( HCO 3 ) 2 ⟶ 2 Al ( OH ) 3 ↓ + 3 CaSO 4 + 6 CO 2 + 14 H 2 O \text{Al}_2(\text{SO}_4)_3 \cdot 14\text{H}_2\text{O} + 3\text{Ca}(\text{HCO}_3)_2 \longrightarrow 2\text{Al}(\text{OH})_3\downarrow + 3\text{CaSO}_4 + 6\text{CO}_2 + 14\text{H}_2\text{O} Al 2 ​ ( SO 4 ​ ) 3 ​ ⋅ 14 H 2 ​ O + 3 Ca ( HCO 3 ​ ) 2 ​ ⟶ 2 Al ( OH ) 3 ​ ↓ + 3 CaSO 4 ​ + 6 CO 2 ​ + 14 H 2 ​ O

Alkalinity Consumption Rule of Thumb

1.0 mg/L of commercial alum consumes ~0.50 mg/L of natural alkalinity (expressed as CaCO 3 \text{CaCO}_3 CaCO 3 ​ ).

Optimum Coagulation pH Window : 5.5 to 7.5 5.5\text{ to }7.5 5.5 to 7.5 (minimum aluminum solubility occurs between pH 6.0 and 6.2 \text{pH }6.0\text{ and }6.2 pH 6.0 and 6.2 ).

If raw water alkalinity is insufficient ( < 30 – 40 mg/L as CaCO 3 < 30\text{--}40\text{ mg/L as }\text{CaCO}_3 < 30 – 40 mg/L as CaCO 3 ​ ), the hydrogen ions liberated by alum hydrolysis will drive raw water pH below 5.5 5.5 5.5 . In this acidic range, aluminum cannot precipitate as Al ( OH ) 3 ( s ) \text{Al}(\text{OH})_3(s) Al ( OH ) 3 ​ ( s ) and remains in soluble ionic forms ( A l 3 + , A l O H 2 + Al^{3+}, AlOH^{2+} A l 3 + , A lO H 2 + ), causing high filtered water turbidity, severe filter breakthrough, and elevated dissolved aluminum carryover into the distribution system. Operators must feed supplemental base:

Hydrated Lime ( Ca ( OH ) 2 \text{Ca}(\text{OH})_2 Ca ( OH ) 2 ​ ): 1.0 mg/L 1.0\text{ mg/L} 1.0 mg/L commercial alum requires ≈ 0.38 mg/L \approx 0.38\text{ mg/L} ≈ 0.38 mg/L hydrated lime.

Soda Ash ( Na 2 CO 3 \text{Na}_2\text{CO}_3 Na 2 ​ CO 3 ​ ): 1.0 mg/L 1.0\text{ mg/L} 1.0 mg/L commercial alum requires ≈ 0.54 mg/L \approx 0.54\text{ mg/L} ≈ 0.54 mg/L soda ash.

Caustic Soda ( 50 % NaOH 50\%\text{ NaOH} 50% NaOH ): 1.0 mg/L 1.0\text{ mg/L} 1.0 mg/L commercial alum requires ≈ 0.40 mg/L \approx 0.40\text{ mg/L} ≈ 0.40 mg/L caustic soda.

2. Ferric Salts (Ferric Chloride and Ferric Sulfate)

Ferric Chloride ( FeCl 3 \text{FeCl}_3 FeCl 3 ​ ) and Ferric Sulfate ( Fe 2 ( SO 4 ) 3 \text{Fe}_2(\text{SO}_4)_3 Fe 2 ​ ( SO 4 ​ ) 3 ​ ): FeCl 3 + 3 HCO 3 − ⟶ Fe ( OH ) 3 ↓ + 3 Cl − + 3 CO 2 \text{FeCl}_3 + 3\text{HCO}_3^- \longrightarrow \text{Fe}(\text{OH})_3\downarrow + 3\text{Cl}^- + 3\text{CO}_2 FeCl 3 ​ + 3 HCO 3 − ​ ⟶ Fe ( OH ) 3 ​ ↓ + 3 Cl − + 3 CO 2 ​

Alkalinity Consumption : 1.0 mg/L FeCl 3 1.0\text{ mg/L }\text{FeCl}_3 1.0 mg/L FeCl 3 ​ consumes approximately 0.92 mg/L 0.92\text{ mg/L} 0.92 mg/L of alkalinity as CaCO 3 \text{CaCO}_3 CaCO 3 ​ .

Operating Characteristics : Ferric hydroxide flocs are heavier, denser, and settle faster than alum flocs. Ferric operates across a much broader pH window ( 4.0 to 11.0 4.0\text{ to }11.0 4.0 to 11.0 ) and performs reliably in cold water ( < 4 ∘ C < 4^\circ\text{C} < 4 ∘ C ), where alum kinetics degrade. However, ferric solutions are highly corrosive and stain concrete and equipment.

3. Polyaluminum Chloride (PACl) and Aluminum Chlorohydrate (ACH)

PACl coagulants are pre-hydrolyzed, engineered polymeric aluminum formulations with the empirical formula Al n ( OH ) m Cl 3 n − m \text{Al}_n(\text{OH})_m\text{Cl}_{3n-m} Al n ​ ( OH ) m ​ Cl 3 n − m ​ .

Advantages : Because PACl is partially pre-neutralized (basicity 50 % to 83 % 50\%\text{ to }83\% 50% to 83% ), it consumes 50 % to 80 % 50\%\text{ to }80\% 50% to 80% less natural alkalinity than alum, produces significantly lower chemical sludge volume, forms rapidly settling flocs in cold water, and operates effectively across wide pH ranges ( 6.0 to 8.5 6.0\text{ to }8.5 6.0 to 8.5 ).

Coagulant Aids and Synthetic Polymers

Coagulant aids are auxiliary chemicals added to strengthen fragile microflocs, expand operational pH tolerances, accelerate settling velocities, or reduce primary coagulant dosage:

Cationic Polymers (poly-DADMAC, epi-DMA): Positively charged, medium-molecular-weight polymers that act as secondary coagulants or primary coagulants in direct filtration plants, requiring zero alkalinity consumption.

Anionic Polymers (hydrolyzed polyacrylamides): Negatively charged, high-molecular-weight long chains ( 10 6 to 10 7 Da 10^6\text{ to }10^7\text{ Da} 1 0 6 to 1 0 7 Da ) that bridge neutralized microflocs in the presence of divalent cations like C a 2 + Ca^{2+} C a 2 + . Dosed downstream of the flash mixer ( 0.05 to 0.25 mg/L 0.05\text{ to }0.25\text{ mg/L} 0.05 to 0.25 mg/L ).

Non-ionic Polymers (pure polyacrylamides): Electrically neutral polymers that aggregate flocs via hydrogen bonding and physical entanglement.

Activated Silica : Sodium silicate activated with acid or chlorine to produce polysilicic acid micro-gels, strengthening alum flocs in cold, low-turbidity waters.

Weighting Agents : Bentonite clay or powdered activated carbon (PAC) dosed into clean, low-turbidity raw waters to provide ballast and nucleation sites for sweep flocculation.

Rapid (Flash) Mixing Hydraulics and Velocity Gradients

Primary coagulant hydrolysis reactions and charge-neutralization adsorption occur in fractions of a second ( < 0.1 to 1.0 second < 0.1\text{ to }1.0\text{ second} < 0.1 to 1.0 second ). If coagulants are not dispersed instantaneously throughout the entire process stream, localized over-dosing occurs, resulting in chemical waste, poor flocculation, and coagulant carryover.

The Velocity Gradient ( G G G )

The intensity of hydraulic mixing is quantified by the velocity gradient ( G G G ), expressed in reciprocal seconds ( s − 1 s^{-1} s − 1 ): G = P μ V G = \sqrt{\frac{P}{\mu V}} G = μ V P ​ ​

Where:

P P P = Power dissipated into the fluid (Watts or ft ⋅ lb/s \text{ft}\cdot\text{lb/s} ft ⋅ lb/s )

μ \mu μ = Dynamic viscosity of water ( P a ⋅ s Pa\cdot s P a ⋅ s or lb ⋅ s/ft 2 \text{lb}\cdot\text{s/ft}^2 lb ⋅ s/ft 2 )

  • V V V = Volume of the mixing zone ( m 3 m^3 m 3 or ft 3 \text{ft}^3 ft 3 )
  • Flash Mix Design Criteria

Rapid-mix intensity and time are paired design variables. In-line or pump-injection devices may disperse chemical in only a few seconds at high G G G ; mechanical basins often use a longer detention period. Operators verify the approved design, mixer power, flow, and chemical dispersion rather than applying one universal G G G and one universal detention time.

Rapid Mix Configurations

In-Line Static Mixers : Fixed internal elements inside a pipe generating extreme turbulent shear with no moving parts.

Mechanical Flash Mix Chambers : High-speed vertical impellers (radial turbines or marine propellers) in small baffled compartments.

Hydraulic Jumps : Supercritical-to-subcritical flow transitions downstream of Parshall flumes or weir drops that harness gravity dissipation.

Jar Testing Protocol and Operational Optimization

The standard operational laboratory tool for evaluating coagulation-flocculation chemistry is the multi-station jar tester (standard 6-station gang stirrer using 2-liter square B-Ker2 or circular jars with illuminated base). Jar Test Protocol Sequence:

  • [1. Collect Fresh Raw Sample] ---> [2. Fill 6 Jars & Dose Varied Coagulants]
  • --> [3. Rapid Flash Mix: 100-300 RPM (1 min)]
  • --> [4. Slow Flocculation: Tapered 50 -> 30 -> 15 RPM (20 min)]
  • --> [5. Quiescent Settling (15-30 min)]
  • --> [6. Sample Supernatant: Turbidity, pH, Settleability, Residual Al/Fe]
  • Standard Laboratory Procedure

Measure baseline raw water quality: Temperature, pH, turbidity (NTU), total alkalinity, and color.

Dose increasing coagulant increments across jars (e.g., 10 , 15 , 20 , 25 , 30 , 35 mg/L 10, 15, 20, 25, 30, 35\text{ mg/L} 10 , 15 , 20 , 25 , 30 , 35 mg/L ).

Rapid Mix : Spin paddles at 100 to 300 RPM 100\text{ to }300\text{ RPM} 100 to 300 RPM ( G ≈ 300 – 400 s − 1 G \approx 300\text{--}400\text{ s}^{-1} G ≈ 300 – 400 s − 1 ) for 1 minute 1\text{ minute} 1 minute while injecting coagulants simultaneously.

Flocculation Mix : Drop paddle speeds to simulate plant hydraulics (e.g., 50 RPM 50\text{ RPM} 50 RPM for 5 min 5\text{ min} 5 min , 30 RPM 30\text{ RPM} 30 RPM for 10 min 10\text{ min} 10 min , 15 RPM 15\text{ RPM} 15 RPM for 5 min 5\text{ min} 5 min ).

Settling : Stop paddles and record floc settling velocity, noting the time required for flocs to settle 10 cm 10\text{ cm} 10 cm .

Supernatant Analysis : Pipette settled supernatant from sampling ports located 2 inches 2\text{ inches} 2 inches below surface; analyze settled turbidity, final pH, UV-254 absorbance (for TOC removal), and residual dissolved coagulant.

Interpreting Jar Test Data for Plant Control

Optimal Dose : The lowest coagulant dose that produces clear supernatant with settled turbidity < 1.0 – 2.0 NTU < 1.0\text{--}2.0\text{ NTU} < 1.0 – 2.0 NTU , rapid floc settling ( > 1 ft/min > 1\text{ ft/min} > 1 ft/min ), and acceptable final pH.

Cold Water Inversion : In winter ( < 4 ∘ C < 4^\circ\text{C} < 4 ∘ C ), water viscosity doubles, slowing ion transport. Jar tests reveal whether elevating pH, adding 0.1 mg/L 0.1\text{ mg/L} 0.1 mg/L cationic polymer aid, or switching to PACl restores settling performance.