Study guide

4.1 Plat Media, Scale, Classification, Basis of Bearings & Certification

Mississippi Professional Surveyor PS

Track your progress as you read

Finished sections get a check mark.

1 Chapter 1: The Mississippi Section Exam, Licensure Law & the Board

1.1 The Mississippi Section PS Exam: Format, Subjects & Study Plan 1.2 Title 73, Chapter 13 After HB 1150: Definitions, the Board & Part 901 Chapters 1–4 1.3 Qualifications, Surveyor Intern Enrollment, Examinations & Comity 1.4 Certificate of Authority for Surveying Firms 1.5 Continuing Professional Competency, Renewal, Retired Status & Reinstatement

2 Chapter 2: Conduct, Seals, Discipline & Unlicensed Practice

2.1 Code of Professional Conduct & Solicitation of Work (Rule 6.3) 2.2 Seals, Signatures & Responsible Charge 2.3 Disciplinary Grounds, Hearings, Sanctions & Appeals 2.4 Unlicensed Practice, Exemptions, Right of Entry & County Surveyors

3 Chapter 3: Mississippi Standards of Practice: Scope, Classification & Accuracy

3.1 From Rule 21 to Chapter 7: Types of Surveys and Attestation 3.2 Survey Classification: Class A, B & C (and the Retired Class D) 3.3 Unadjusted Closure & Angular Closure 3.4 Bearing, Distance, Elevation & Improvement Tolerances; GNSS Quality Control

4 Chapter 4: Mississippi Standards of Practice: Plat Contents & Monumentation

4.1 Plat Media, Scale, Classification, Basis of Bearings & Certification 4.2 Monuments, Alternate Monuments, Exceptions & Witness Corners 4.3 Discrepancies, Occupation, Encroachments, Rights-of-Way & Descriptions

5 Chapter 5: The Public Land Survey System in Mississippi: Meridians, Cessions & Private Claims

5.1 The Five Principal Meridians Governing Mississippi Surveys 5.2 Indian Cessions, State Boundaries & the Original GLO Surveys 5.3 Colonial Grants, Private Land Claims & Ellicott's Line

6 Chapter 6: PLSS Township Subdivisions, Section Fractionalization & Retracements

6.1 Township Exterior Boundaries, Convergency of Meridians, and Section Breakdown 6.2 Section Subdivisions, Aliquot Parts, and Government Lots 6.3 Retracement Surveys, Original Evidence & the BLM Manual

7 Chapter 7: Lost Corner Restoration & Retracement in Mississippi

7.1 Existent, Obliterated & Lost Corners: Classification and Evidence 7.2 Single Proportionate Measurement Methods 7.3 Double Proportionate Measurement Methods

8 Chapter 8: Mississippi Boundary Law: Hierarchy of Calls & Deed Interpretation

8.1 The Hierarchy of Conflicting Calls & the Intent of the Parties 8.2 Senior Rights vs. Junior Rights in Overlapping Conveyances 8.3 Legal Description Types & Ambiguity Resolution

9 Chapter 9: Adverse Possession, Acquiescence, and Boundary Agreements in Mississippi

9.1 Adverse Possession under Miss. Code Ann. § 15-1-13 9.2 Boundary by Agreement, Acquiescence & Estoppel 9.3 The Surveyor's Role in Possession, Encroachment & Title Disputes

10 Chapter 10: Water Boundaries, Riparian Rights & Public Trust Tidelands in Mississippi

10.1 Non-Tidal Rivers & Streams: Bed Ownership, Public Waterways & Meander Lines 10.2 Accretion, Reliction, Erosion & Avulsion 10.3 Public Trust Tidelands & Mean High Water on the Mississippi Coast

11 Chapter 11: Easements, Rights-of-Way, and Sixteenth Section School Trust Lands

11.1 Easements: Types, Creation, Scope & What the Plat Must Show 11.2 Highway, County Road, Railroad & Utility Rights-of-Way 11.3 Sixteenth Section & Lieu Lands: School Trust Title, Classification & Surveys

12 Chapter 12: Geodetic Control, State Plane Coordinates & Professional Practice

12.1 The Mississippi Coordinate System (§§ 89-6-1 to -19): Zones, Parameters & Grid-to-Ground 12.2 GNSS Positioning in Mississippi: Rule 7.5(2), the GCGC RTN, CORS & Quality Control 12.3 Professional Liability, Survey Contracts & Expert Testimony

4.1 Plat Media, Scale, Classification, Basis of Bearings & Certification

Key Takeaways Explain This Topic AI

Mississippi boundary plats must be on stable, durable, reproducible media, and no plat or map may be smaller than 8-1/2 by 11 inches (Rule 7.3).

Every boundary plat must show its scale, area, and survey classification of A, B, or C (Rule 7.3).

A survey must be referenced to true north, grid north, or the record bearing of a well-defined monumented line, and the plat must state the meridian and how it was obtained (Rule 7.3).

Every circular curve on a Mississippi boundary plat must show four elements: radius, arc length, chord bearing, and chord length (Rule 7.3).

The licensee's signature and seal on a plat certify that the survey meets the Mississippi Standards of Practice for Surveying (Rule 7.3).

Last updated: September 2026

The Rule 7.3 checklist for the drawing

Rule 7.3 opens: "The boundary, route, easement, and lease survey plat shall conform to the following requirements and shall include the following information." The table groups the nineteen items by topic, with the section of this guide that covers each.

Item Requirement (paraphrased) Covered in

1 Stable, durable drawing paper, vellum, linen, or film of reproducible quality; no plat smaller than 8-1/2 × 11 inches This section

  • 2 Scale, area, and classification (A, B, or C) This section and 3.2
  • 3 Reference meridian rules and a definitive north arrow This section
  • 4–7 Monuments found or set; monument specifications; exceptions; witness corners Section 4.2
  • 8 Metes-and-bounds plats show the monumented commencing point and point of beginning Section 4.2
  • 9–10 Discrepancies and sources; physical evidence of occupation Section 4.3
  • 11 Length and direction of each line, both record and measured This section
  • 12 Four elements of all circular curves This section
  • 13 Content of a surveyor-prepared description Section 4.3
  • 14 Lot, block, or tract designations, including adjoiners in a recorded subdivision This section
  • 15–17 Encroachments; rights-of-way and easements; permanent improvements Section 4.3
  • 18 State Plane Coordinate items Section 3.4
  • 19 Name, address, date of field survey, signature, and seal; certification This section
  • Item 1: media and size

The plat must be on "any reasonably stable and durable drawing paper, vellum, linen, or film of reproducible quality," and " no plat or map shall have dimensions of less than 8-1/2 × 11 inches ." That is the whole of the Chapter 7 media rule. It sets no margin widths, lettering heights, or paper weights; recording offices may have their own formatting requirements. A 5 × 8-inch sketch violates the rule. An 8-1/2 × 11 plat meets it if the scale shows the detail the classification needs.

Item 2: scale, area, and classification

The plat must show its scale , the area , and the classification (A, B, or C) under Rule 7.4, and the scale must be sufficient to show the detail the class requires. The rule does not require both a graphic bar scale and a stated scale, but a bar scale is good practice because plats are copied and resized.

Item 3: basis of bearings and north arrow

Under Rule 7.3.3, the survey must be referenced to one of three things:

  • true north ;
  • grid north ; or

the record bearing of a well-defined and monumented line found in (a) existing subdivisions, (b) city or town plats, or (c) a previous survey, when the current survey divides that earlier survey and enough monumentation remains to re-establish the original orientation.

The rule adds:

  • (a) a definitive north arrow shall be shown on the plat;
  • (b) the reference meridian must be clearly stated on the plat along with the method used to obtain it ; and

(c) if a reference line is used, the monuments defining it must be shown and described, the line noted as the reference line, and the recording information of the source cited.

Magnetic north is not on the list. The 2015 rule allowed a compass meridian if it was properly declinated and adjusted to a true meridian. The 2025 rule allows only true north, grid north, or a monumented record line. A plat stating "bearings based on magnetic north observed in 2026" does not meet Rule 7.3.3. A plat labeled only "North," with no stated meridian or method, also fails.

Plat note Compliant?

"Bearings are grid north, Mississippi Coordinate System of 1983, West Zone, derived from GNSS observations tied to [named control]" Yes; also triggers the State Plane items (Section 3.4)

"Bearings are true north from GNSS-derived geodetic azimuth" Yes, if the method is stated

"Bearings based on the record bearing of the south line of Block 4, Oak Grove Subdivision, Plat Book 12, Page 45, between the found 1/2-inch iron pins shown" Yes; monuments shown and source cited

  • "Magnetic bearings, declination 0°30′ W" No; not an allowed reference under the current rule
  • Arrow labeled "N" with no note No; meridian and method not stated
  • Item 11: record and measured lines

The plat must show the horizontal length (distance) and direction (bearing or azimuth) of each line as specified in the legal description and as determined in the actual survey . When record and measured values differ, both appear, for example "S 89°12′ E 418.50′ (M) / S 89°30′ E 400.00′ (R)". This supports the discrepancy disclosure in item 9 (Section 4.3).

Item 12: curves

"Four (4) elements of all circular curves shall be shown ( radius, arc length, chord bearing and chord length )." Delta angle and tangent length are useful but not required. A curve labeled only with its radius and arc length does not meet item 12.

Item 14: lot and block

If the survey is within a recorded subdivision, the plat must show the lot, block, or tract numbers or other designations, including those of adjoining lots and tracts .

Item 19: identification and certification

"Regardless of the type of survey, a plat or survey shall bear the name, address, date of field survey, signature, and seal of the licensee in responsible charge. This signature and seal are certification that the survey meets the requirements of the Standards of Practice for Surveying in Mississippi ." The item also requires following the Manual of Instructions for the Survey of U.S. Public Lands and Mississippi's subdivision laws.

Three points follow from the text:

The rule prescribes no standard certificate wording . The seal and signature are the certification. Firms add a written certificate, often addressed to the client, lender, and title insurer, but the obligation comes from the rule, not the wording.

The date of field survey is required and is separate from the date the seal was affixed, which Rule 7.2 also requires.

Chapter 7 does not require the firm's COA number on the plat. Monuments set must bear the PS license number, the firm's COA number, or the agency name (Section 4.2), and Rule 6.2 requires each sheet to be signed, sealed, and dated.

Plats of towns and subdivisions: the older statute

Mississippi also has a nineteenth-century platting statute for cities, towns, villages, and additions (§§ 19-27-21 to -31):

The proprietor must have a true map or plat made by a civil engineer, surveyor, or other competent person (§ 19-27-21). Surveying for new subdivision lines is now reserved to licensed surveyors under § 73-13-3(7)(b).

The plat must be drawn at a scale not less than 200 feet to an inch on 18 × 24-inch sheets. It must describe the land (township, range, sections, and parts of sections), name the proprietor and surveyor, show the cardinal points and a correct scale, and be signed and acknowledged like a deed (§ 19-27-23).

It must describe the government-survey portion platted, using metes and bounds if legal subdivisions will not describe it, and show public grounds, streets, alleys, lots, blocks, and all gores and irregular lots with their dimensions (§ 19-27-25).

It is recorded in the chancery clerk's office. Selling lots before recording exposes the seller to a $200 action for the county's use (§ 19-27-29). Vacation or alteration requires a chancery court petition (§ 19-27-31).

Local subdivision ordinances usually add requirements. A subdivision plat must satisfy the statute, the local ordinance, and Chapter 7.