Study guide
9.1 Electrical Safety on Construction Sites: Temporary Supply, RCDs, Competent Persons and Safe Isolation
NIOSH Site Safety Supervisor SSS
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: The SSS Role & Malaysian OSH Legislation
1.1 The Site Safety Supervisor: Legal Appointment, DOSH Registration & Core Duties 1.2 OSHA 1994 as Amended by Act A1648: Structure, Duties, Rights & Penalties 1.3 Regulations Under OSHA 1994 That a Site Safety Supervisor Applies 1.4 CDM Regulations 2024: Duty Holders, Notification, Plans and Site Requirements
2 Chapter 2: OSH Management Systems, Human Factors & Risk Management
2.1 OSH Management Systems: Planning, OSH Policy, Site Organisation & Safety Committees 2.2 Human and Behavioural Factors in Construction Safety 2.3 HIRARC and the General Principles of Prevention 2.4 Safe Work Procedures and Permit-to-Work Systems 2.5 Monitoring, Accident Investigation, NADOPOD Reporting, Record Keeping & Audit
3 Chapter 3: Site Planning, General Control, Welfare & Communication
3.1 Site Initial Planning, Hoarding, Access and Vehicle & Plant Movement 3.2 General Control and Welfare: Housekeeping, Storage, Site Security, Welfare Facilities and First Aid 3.3 Safety Communication: Site Induction, Toolbox Meetings, Signs and Safety Promotion
4 Chapter 4: Working at Height & Fall Protection
4.1 Working at Height: Legal Basis, Fall Physics and the Fall-Control Hierarchy 4.2 Collective Fall Protection: Guardrails, Floor Openings, Nets and Catch Platforms 4.3 Personal Fall Protection, Ladders, MEWPs and Rescue from Height
5 Chapter 5: Scaffolding: Components, Design, Erection & Inspection
5.1 Scaffolding Types, Components, Foundations, Bracing and Tower Scaffolds 5.2 Scaffold Design, Loading, Competent Scaffolders and Safe Erection & Dismantling 5.3 Scaffold Inspection, Tagging Systems and Records
6 Chapter 6: Excavation, Shoring & Underground Services
6.1 Excavation Hazards, Soil Behaviour and Pre-Excavation Investigation 6.2 Protecting Excavation Sides: Battering, Benching, Shoring and Trench Support Systems 6.3 Deep Excavations, Retaining Systems, Cofferdams & Caissons, Monitoring and Rescue 6.4 Excavation Access, Edge Protection, Inspection Reports, Underground Services, Water and Air
7 Chapter 7: Piling, Formwork & Falsework, Concrete Work & Demolition
7.1 Piling Operations: Rigs, Working Platforms, Driven and Bored Piles 7.2 Formwork and Falsework: Temporary Works Design, Erection, Inspection and Loading 7.3 Concrete Work: Pre-Pour Checks, Pumping and Placing, Cement Health Hazards and Striking 7.4 Demolition and Dismantling: Surveys, Written Arrangements, Methods, Debris and Asbestos
8 Chapter 8: Lifting Operations, Work Equipment & Mobile Plant
8.1 Cranes and Hoists: Certificates of Fitness, Competent Operators, Ground and Crane Safety 8.2 Lifting Tackle and Rigging: Slings, Shackles, Hooks, Inspection and Discard 8.3 Lift Planning, Load Charts, Sling Angles and Crane Signalling 8.4 Work Equipment and Mobile Plant: Earthmoving Machines, Hand and Power Tools, Compressors and Guarding
9 Chapter 9: Electrical Safety, Fire & Hot Work, and Confined Spaces
9.1 Electrical Safety on Construction Sites: Temporary Supply, RCDs, Competent Persons and Safe Isolation 9.2 Fire Safety, Emergency Arrangements, Hot Work and Welding 9.3 Confined Spaces: The 2010 ICOP, Hazardous Atmospheres, Roles, Permits and Rescue
10 Chapter 10: Occupational Health Hazards & Controls
10.1 Physical Hazards: Noise, Vibration, Heat Stress, Radiation and Lighting 10.2 Musculoskeletal Hazards: Manual Handling and Ergonomics on Construction Sites 10.3 Chemical and Biological Hazards: USECHH, CLASS, Silica, Asbestos, Lead and Site Infections 10.4 Psychological Health: Psychosocial Hazards, Stress, Fatigue, Violence and Substance Misuse 10.5 Personal Protective Equipment and Site Emergency Response
11 Chapter 11: The SSS Examination: Paper 1, Site Assessment & Presentation
11.1 The SSS Examination: Entry Rules, Format, Retakes and Paper 1 Technique 11.2 Paper 2: Site Visit Practice, the Site Assessment and the Online HIRARC Presentation
9.1 Electrical Safety on Construction Sites: Temporary Supply, RCDs, Competent Persons and Safe Isolation
Key Takeaways Explain This Topic AI
CDM 2024 regulation 27(1) requires energy distribution installations on a construction site to be suitably located, checked regularly and clearly marked where necessary to prevent danger.
Regulation 36(3) of the Electricity Regulations 1994 requires final circuits in installations where hand-held equipment is used to be protected by a residual current device rated at no more than 30 mA.
Regulation 36 of the Electricity Regulations 1994 sets RCD ratings of no more than 10 mA for wet locations such as bathrooms and no more than 100 mA for other installations not covered by the 10 mA and 30 mA rules.
Under the Electricity Regulations 1994, electrical installation work is done and supervised by competent persons holding Energy Commission certificates of competency, such as wiremen and chargemen.
An electrical short circuit or overload with fire or explosion that stops plant for more than 24 hours and could cause serious injury is a NADOPOD dangerous occurrence.
Last updated: October 2026
How electricity harms
Effect Mechanism Construction example
Electric shock Current through the body disturbs heart rhythm and causes muscle spasm; can cause ventricular fibrillation and death Damaged extension lead on a wet slab; drilling into a live cable
Burns Heating where current enters and leaves; arc flash Arc from a fault in a distribution board; contact with overhead lines
Secondary injuries A shock causes a fall from height or a ladder Worker on a ladder jolted by a faulty drill
Fire and explosion Overloaded or damaged cables, poor connections, sparks in flammable atmospheres Overloaded multi-adaptor in a site cabin; grinder sparks near solvent
Risk rises with wet conditions (Malaysian rain, concrete work, dewatering), damaged insulation, steel structures and confined conductive spaces, and long cable runs across traffic routes.
The law
OSHA 1994 section 15(2)(a): safe plant and systems of work.
CDM 2024 regulation 27:
(1) energy distribution installations must be suitably located, checked regularly and clearly marked where necessary to prevent danger
(2) and (3) overhead power cables must be diverted, isolated and earthed, or protected with warning notices, barriers and suspended protection
- (4) no work that could create risk from underground services unless suitable measures are taken
- most breaches carry up to RM500,000 or one year or both
Electricity Supply Act 1990 (Act 447) and Electricity Regulations 1994 , administered by the Energy Commission (Suruhanjaya Tenaga) :
electrical work must be done by persons holding the appropriate certificate of competency : wireman, chargeman, electrical supervisor, competent electrical engineer or cable jointer
- installations must be done by registered electrical contractors
- installations must be tested and certified before connection to supply
Regulation 36 of the Electricity Regulations 1994 , protection against earth leakage by residual current devices (RCDs) :
- Situation Maximum rated residual operating current
- Wet locations such as bathrooms, and where the body's resistance is likely to be low (36(2)) 10 mA
Final circuits in installations where hand-held equipment, apparatus or appliances are used or likely to be used (36(3)) 30 mA
Other installations (36(4)) 100 mA
On construction sites, hand tools are everywhere, so every final circuit feeding socket outlets for portable tools needs 30 mA RCD protection . The international standard for construction-site installations, IEC 60364-7-704, takes the same approach.
Temporary site distribution
A typical arrangement runs from the utility supply or a generator to a main board, then sub-distribution boards, then socket-outlet boards near the work.
What the SSS inspects
Item Good condition
Boards Weatherproof enclosure; lockable; doors closed; labelled with circuits and a warning sign; no exposed live parts; stable stand off the ground; access kept clear
Protection RCDs fitted as Regulation 36 requires and tested using the test button , for example weekly, and periodically by a competent person with an instrument; correctly rated breakers; earthing in place
Cables Correct type for site use; not damaged, joined with tape or repaired with insulation tape; routed overhead or buried and protected; ramps where vehicles cross; kept out of water
Plugs and sockets Industrial-type connectors; no bare wires pushed into sockets; no multi-adaptor chains
Generators Located outdoors away from excavations, basements and openings (fumes); earthed as designed; fuel stored safely; refuelled only when stopped
Lighting Temporary lighting guarded and secure; stair and access lighting maintained (CDM regulation 37)
Only competent persons (Energy Commission certificates) may install, alter or repair the installation. Workers must never "borrow" power by opening boards.
Portable tools and equipment
Inspect before use: user checks for damaged casings, cables and plugs. Withdraw defective tools at once and tag them "DO NOT USE".
Inspect and test periodically: by a competent person, with a site tag or register showing the next due date.
Choose safer supplies: battery tools or reduced-voltage systems (such as 110 V centre-tapped earth transformers) where practicable, especially in wet or confined areas. Double-insulated tools reduce shock risk.
Never use domestic extension reels on site, and never use tools with missing earth pins.
Working near cables
Overhead lines: CDM regulation 27 and Section 3.1. Check the line owner's safe distance, set goalposts and barriers at crossings, and plan crane, pump and tipper positions so they cannot reach the line.
Underground cables: use drawings, cable locator scans and hand-dug trial holes (Section 6.4). DOSH's excavation bulletin also says workers using hand tools where the exact cable location is unknown should wear insulated gloves and footwear.
Safe isolation and work on electrical systems
Work on or near electrical equipment should be done dead wherever possible:
Identify the circuit and equipment from drawings and labels.
Isolate at the correct point. Switching off a final circuit breaker is not enough if other supplies feed the equipment.
Lock off with a personal lock and tag each isolation point. Use an electrical permit for complex systems.
Prove dead with an approved voltage indicator, which is itself checked on a known live source before and after use.
Earth where required, for example on high-voltage systems, by an authorised person.
Re-energise only after all workers are clear, all locks removed by their owners, and the work checked.
Live work should be avoided. Where it is unavoidable, it must be done only by competent persons following a specific procedure, with insulated tools, PPE and a second person present.
Responding to electric shock
Do not touch the casualty until the supply is switched off or the casualty is separated using non-conductive means. For high-voltage lines, keep well clear and call the line owner.
Call for help (999) and start CPR if the casualty is not breathing normally. Use an automated external defibrillator (AED) if one is available.
Treat burns , and send every shock casualty for medical assessment, because internal injuries and heart rhythm problems can be delayed.
Report and investigate. A shock causing serious injury, or an electrical fire with a long plant stoppage (NADOPOD Second Schedule item 3), may need notification to DOSH.
Scenario: the wet basement
During rain, workers in a flooded basement are using a pump and a grinder plugged into a board with its door off, through a taped joint lying in water. The RCD test record has not been updated for two months. The SSS:
Stops work, clears the area and has the board isolated by the site chargeman.
Has the damaged cable replaced, the joint removed, and the cable routed off the floor on hooks.
Has the RCDs tested and shown to trip within their rated current, confirms the 30 mA protection on the tool circuits as Regulation 36(3) requires, and refits the board door with a lock.
Swaps the grinder for a battery tool. The pump supply is reviewed by the electrical engineer.
Adds weekly RCD test-button checks to the site inspection checklist.