Study guide
10.2 Musculoskeletal Hazards: Manual Handling and Ergonomics on Construction Sites
NIOSH Site Safety Supervisor SSS
Track your progress as you read
Finished sections get a check mark.
1 Chapter 1: The SSS Role & Malaysian OSH Legislation
1.1 The Site Safety Supervisor: Legal Appointment, DOSH Registration & Core Duties 1.2 OSHA 1994 as Amended by Act A1648: Structure, Duties, Rights & Penalties 1.3 Regulations Under OSHA 1994 That a Site Safety Supervisor Applies 1.4 CDM Regulations 2024: Duty Holders, Notification, Plans and Site Requirements
2 Chapter 2: OSH Management Systems, Human Factors & Risk Management
2.1 OSH Management Systems: Planning, OSH Policy, Site Organisation & Safety Committees 2.2 Human and Behavioural Factors in Construction Safety 2.3 HIRARC and the General Principles of Prevention 2.4 Safe Work Procedures and Permit-to-Work Systems 2.5 Monitoring, Accident Investigation, NADOPOD Reporting, Record Keeping & Audit
3 Chapter 3: Site Planning, General Control, Welfare & Communication
3.1 Site Initial Planning, Hoarding, Access and Vehicle & Plant Movement 3.2 General Control and Welfare: Housekeeping, Storage, Site Security, Welfare Facilities and First Aid 3.3 Safety Communication: Site Induction, Toolbox Meetings, Signs and Safety Promotion
4 Chapter 4: Working at Height & Fall Protection
4.1 Working at Height: Legal Basis, Fall Physics and the Fall-Control Hierarchy 4.2 Collective Fall Protection: Guardrails, Floor Openings, Nets and Catch Platforms 4.3 Personal Fall Protection, Ladders, MEWPs and Rescue from Height
5 Chapter 5: Scaffolding: Components, Design, Erection & Inspection
5.1 Scaffolding Types, Components, Foundations, Bracing and Tower Scaffolds 5.2 Scaffold Design, Loading, Competent Scaffolders and Safe Erection & Dismantling 5.3 Scaffold Inspection, Tagging Systems and Records
6 Chapter 6: Excavation, Shoring & Underground Services
6.1 Excavation Hazards, Soil Behaviour and Pre-Excavation Investigation 6.2 Protecting Excavation Sides: Battering, Benching, Shoring and Trench Support Systems 6.3 Deep Excavations, Retaining Systems, Cofferdams & Caissons, Monitoring and Rescue 6.4 Excavation Access, Edge Protection, Inspection Reports, Underground Services, Water and Air
7 Chapter 7: Piling, Formwork & Falsework, Concrete Work & Demolition
7.1 Piling Operations: Rigs, Working Platforms, Driven and Bored Piles 7.2 Formwork and Falsework: Temporary Works Design, Erection, Inspection and Loading 7.3 Concrete Work: Pre-Pour Checks, Pumping and Placing, Cement Health Hazards and Striking 7.4 Demolition and Dismantling: Surveys, Written Arrangements, Methods, Debris and Asbestos
8 Chapter 8: Lifting Operations, Work Equipment & Mobile Plant
8.1 Cranes and Hoists: Certificates of Fitness, Competent Operators, Ground and Crane Safety 8.2 Lifting Tackle and Rigging: Slings, Shackles, Hooks, Inspection and Discard 8.3 Lift Planning, Load Charts, Sling Angles and Crane Signalling 8.4 Work Equipment and Mobile Plant: Earthmoving Machines, Hand and Power Tools, Compressors and Guarding
9 Chapter 9: Electrical Safety, Fire & Hot Work, and Confined Spaces
9.1 Electrical Safety on Construction Sites: Temporary Supply, RCDs, Competent Persons and Safe Isolation 9.2 Fire Safety, Emergency Arrangements, Hot Work and Welding 9.3 Confined Spaces: The 2010 ICOP, Hazardous Atmospheres, Roles, Permits and Rescue
10 Chapter 10: Occupational Health Hazards & Controls
10.1 Physical Hazards: Noise, Vibration, Heat Stress, Radiation and Lighting 10.2 Musculoskeletal Hazards: Manual Handling and Ergonomics on Construction Sites 10.3 Chemical and Biological Hazards: USECHH, CLASS, Silica, Asbestos, Lead and Site Infections 10.4 Psychological Health: Psychosocial Hazards, Stress, Fatigue, Violence and Substance Misuse 10.5 Personal Protective Equipment and Site Emergency Response
11 Chapter 11: The SSS Examination: Paper 1, Site Assessment & Presentation
11.1 The SSS Examination: Entry Rules, Format, Retakes and Paper 1 Technique 11.2 Paper 2: Site Visit Practice, the Site Assessment and the Online HIRARC Presentation
10.2 Musculoskeletal Hazards: Manual Handling and Ergonomics on Construction Sites
Key Takeaways Explain This Topic AI
DOSH's Guidelines for Manual Handling at Workplace 2018 give recommended weights that protect around 95% of working men and women; the guideline says they are not safe limits, and tasks more than about twice the filter values may be a serious risk.
Under DOSH's 2018 manual handling guideline, the recommended lifting weight is reduced by 30% for one or two lifts a minute, 50% for five to eight lifts a minute and 80% for more than 12 lifts a minute.
DOSH's 2018 guideline reduces the recommended weight by 10% when the body twists 45 degrees and by 20% at 90 degrees.
DOSH's 2018 guideline gives an acceptable carrying distance of 2 to 10 metres; carrying further than 10 metres exceeds the limit and calls for an advanced ergonomic risk assessment.
Ergonomic risk factors include awkward posture, forceful exertion, repetitive motion, static and sustained posture, contact stress, vibration and environmental factors such as heat and lighting.
Last updated: October 2026
Why musculoskeletal health is on the SSS syllabus
Construction work involves heavy, awkward loads (blocks, cement bags, rebar, formwork panels, pipes, kerbs), repetitive tasks (tying rebar, laying tiles, plastering), work above the shoulders or at floor level, vibrating tools, and heat. The result is musculoskeletal disorders (MSDs) : low back pain, disc injuries, shoulder and neck strain, tendon disorders, hernias, and hand-arm conditions.
The law is general but clear:
OSHA 1994 section 15(2)(a), (b) and (c): safe systems of work and handling, with information, training and supervision.
Section 18B: risk assessment of manual handling tasks.
CDM 2024 First Schedule: principle 4 requires adapting the work to the individual , especially in the design of workplaces, the choice of plant and the choice of working methods, to reduce monotonous work and work at a predetermined rate.
DOSH's Guidelines for Manual Handling at Workplace 2018 , and its ergonomic risk assessment guidelines, give the method.
Ergonomic risk factors
DOSH's guidelines describe the following risk factors:
Risk factor Meaning Construction example
Awkward posture Joints far from neutral: bending, twisting, overreaching Tying rebar at ground level for hours; overhead drilling into slabs
Forceful exertion High physical effort; higher with speed, vibration or awkward posture Lifting 50 kg cement bags; pulling cables; pushing loaded barrows
Repetitive motion The same movements repeated with little rest Laying blocks or tiles; screwing drywall
Static and sustained posture Holding one position for a long time Holding a breaker against a wall; kneeling to tile
- Contact stress Pressure from hard or sharp edges Carrying steel bars on the shoulder; kneeling on rebar
- Vibration Hand-arm or whole-body vibration Breakers, compactors, operating plant over rough ground
Environmental factors Heat, humidity, lighting and noise affecting performance Lifting on hot roofs; poor lighting in basements
Types of manual handling task
The DOSH guideline covers four types:
- lifting and lowering
- pushing and pulling
- carrying
- holding and restraining
It also covers handling while seated . Holding does not need a heavy load: even a light load held for a long time can cause injury.
The initial manual handling risk assessment (DOSH 2018)
The initial assessment is a quick screen. If the task is within the recommended weights, a fuller assessment is normally not needed, unless individual workers are at particular risk, such as pregnant workers, young or new workers, or those with health problems or recent injuries. If the recommended weight is exceeded, carry out an advanced ergonomic risk assessment and control the risk.
DOSH emphasises that the recommended values:
- give a reasonable level of protection to around 95% of working men and women
- are not "safe" or maximum weight limits : there is no threshold where handling changes from safe to unsafe
mean that operations more than about twice the filter values may be a serious risk of injury , even for fit, trained people
Lifting and lowering
The guideline's Figure 5.2 gives recommended weights by hand height and distance from the body , separately for men and women. In the guideline's own example, a man lifting between knuckle and elbow height, close to the body , has a recommended weight of 25 kg . The reductions are:
Repetition (Table 5.2):
- Frequency Reduce the recommended weight by
- Once or twice per minute 30%
- Five to eight times per minute 50%
- More than 12 times per minute 80%
Twisting (Table 5.3):
- Twisting from facing forward Reduce the recommended weight by
- 45 degrees 10%
- 90 degrees 20%
Worked example (DOSH 2018). Starting value: 25 kg . The worker twists about 45° to place the load, so the reduction is 10% of 25 kg = 2.5 kg . The worker lifts 5 to 8 times a minute , so a further reduction of 50% of 25 kg = 12.5 kg applies. The recommended weight is: 25 − 2.5 − 12.5 = 10 kg 25 - 2.5 - 12.5 = 10\ \text{kg} 25 − 2.5 − 12.5 = 10 kg
If the actual load is heavier than 10 kg, an advanced ergonomic risk assessment is needed.
Construction example: a block layer lifting 15 kg hollow blocks from a pallet on the floor up to a wall at chest height, six times a minute, while twisting, is well outside the filter. Raise the pallet to working height, reduce twisting, rotate tasks, or use lighter blocks or mechanical aids.
Pushing and pulling (Table 5.4)
These values apply when force is applied with the hands, the hands are between knuckle and shoulder height, the distance is under 20 m , the load is on wheels, and the handling aid is well maintained:
Activity Men Women
Starting or stopping a load About 1,000 kg on a smooth level surface (about 200 N push force) About 750 kg (about 150 N)
Keeping the load moving About 100 kg on an uneven level surface (about 100 N) About 70 kg (about 70 N)
The guideline notes that moving a load on a flat surface needs at least about 2% of the load weight in force, and up to about 10% on uneven surfaces. Reduce the weight on slopes and ramps. Keep barrow and trolley routes smooth and level.
Carrying (Table 5.5)
Factors to check:
floor surface: worn, uneven, wet, sloping or unstable surfaces, or unsuitable footwear, call for an advanced assessment
- environment: extremes of temperature, strong air movement, or poor lighting
- carry distance: 2 to 10 m is acceptable; more than 10 m exceeds the limit
- obstacles: steep slopes, steps, closed doors, tripping hazards and ladders all call for an advanced assessment
- Controls
Follow the hierarchy (Section 2.3) and the CDM principle of adapting work to the individual:
Avoid or eliminate:
- deliver materials by crane or hoist to the floor where they are needed
- use pre-cut or prefabricated components
- design out lifting, for example with mechanical block grabs
Mechanical aids:
trolleys, barrows, pallet trucks, vacuum lifters, panel lifters, hoists, telehandlers with the right attachments
maintain wheels and surfaces so pushing forces stay low
Reduce the load:
- order smaller bags or lighter blocks where the specification allows
- split loads; use team lifts with a nominated leader and clear signals
Improve the task and layout:
- keep loads between knuckle and elbow height and close to the body
- avoid twisting by arranging the work area
- reduce carrying distances and steps
- provide good lighting and clear, dry routes
Organise the work:
- rotate workers between heavy and light tasks
- schedule rest breaks, especially in heat
- set a realistic pace, not one driven by piece rates alone
Training: teach good handling technique (plan the lift; stable base; bend the knees; keep the load close; no twisting; lift smoothly), but remember that technique training alone does not make an unsuitable task safe .
Health:
- encourage early reporting of aches and pains
- adjust tasks for pregnant workers, young workers and those returning from injury
- provide knee pads, padded gloves and shoulder pads for contact stress
- Scenario: the cement bag gang
Workers unload 50 kg cement bags from a lorry and carry them 30 m across rough ground and up a stair to a mixer, all morning. The SSS's assessment:
- the load is far above the filter for any height
- repetition is high
- carrying distance exceeds 10 m
- the route has uneven ground and steps
All of these call for an advanced assessment and immediate control. The SSS recommends:
Crane or forklift delivery of palletised bags next to the mixer.
A smooth trolley route for any remaining moves.
Smaller bags where the supplier offers them.
Bag splitters that let workers empty bags at the mixer without lifting them high.
Task rotation and rest breaks.
A toolbox briefing on reporting early symptoms.