Study guide

14.2 System Labeling and Signage Requirements

NABCEP PV Installation Professional PVIP

Track your progress as you read

Finished sections get a check mark.

1 Introduction & Exam Overview

About the NABCEP PVIP Exam Using the 2017 NEC on Exam Day

2 Chapter 1: Solar Resource & Site Assessment

1.1 Sun Position, Irradiance, and Insolation 1.2 Site Survey and Roof Condition Assessment 1.3 Shading Analysis and Solar Access 1.4 Array Layout and Fire Code Setbacks

3 Chapter 2: Photovoltaic Modules & Cell Technology

2.1 PV Cell Technologies and Manufacturing 2.2 Electrical Performance Characteristics & I-V Curves 2.3 Module Degradation, Testing Standards, and Warranties

4 Chapter 3: Inverters & System Architectures

3.1 Inverter Types and Topologies 3.2 Inverter Efficiency, Features, and Grid Interaction 3.3 System Configurations: Grid-Direct vs Stand-Alone 3.4 Hybrid and AC-Coupled vs DC-Coupled Architectures

5 Chapter 4: Mechanical Mounting & Roofing Systems

4.1 Sloped Roof Mounting and Flashing Methods 4.2 Low-Slope Ballasted and Penetrating Systems 4.3 Ground Mounts and Tracking Systems

6 Chapter 5: Structural Loading & Mechanical Assembly

5.1 Structural Load Calculations and Engineering 5.2 Mechanical Assembly and Hardware Specifications 5.3 Wire Management and Array Mechanical Protection

7 Chapter 6: Electrical Calculations & Sizing

6.1 Maximum System Voltage and Temperature Calculations 6.2 Maximum Circuit Current and Overcurrent Protection 6.3 Conductor Sizing and Ampacity Derating 6.4 Voltage Drop Analysis and Sizing in PV Systems

8 Chapter 7: Electrical Equipment & Safety Disconnects

7.1 PV Disconnecting Means and Isolation 7.2 Wiring Methods, Raceways, and Connectors 7.3 Combiner Boxes and DC Balance of System 7.4 Monitoring, Controls, and Communications

9 Chapter 8: Grounding, Bonding & Fire Safety

8.1 Equipment Grounding and System Bonding 8.2 Ground-Fault Protection and Arc-Fault Interrupters 8.3 Rapid Shutdown Systems

10 Chapter 9: Utility Interconnection & Grid Integration

9.1 Utility Interconnection Standards & Permitting 9.2 Load-Side Interconnection and the 120% Rule 9.3 Supply-Side Interconnection and Alternative Connections

11 Chapter 10: Energy Storage Systems (ESS)

10.1 Battery Chemistries, Characteristics, and Ratings 10.2 Energy Storage System Sizing and Autonomy 10.3 NEC Article 706 and Electrical Storage Rules 10.4 ESS Safety Standards, NFPA 855, and Fire Codes

12 Chapter 11: System Commissioning & Acceptance Testing

11.1 Visual Inspection and Pre-Power Verification 11.2 Voltage and Current Commissioning Tests 11.3 Insulation Resistance Testing and Megohmmeter Procedures 11.4 I-V Curve Tracing and Performance Analysis

13 Chapter 12: Operations, Maintenance & Troubleshooting

12.1 Preventive Maintenance and Monitoring 12.2 Thermal Imaging and Infrared Inspection 12.3 Electrical Fault Troubleshooting and Diagnostics 12.4 Corrective Maintenance and Component Replacement

14 Chapter 13: Workplace Safety, OSHA & NFPA 70E

13.1 OSHA Regulations and Personal Protective Equipment 13.2 Fall Protection Systems and Ladder Safety 13.3 Electrical Safety, Arc Flash, and NFPA 70E 13.4 Lockout/Tagout (LOTO) and Hazardous Energy Control

15 Chapter 14: Project Management, Codes & Documentation

14.1 AHJ Permitting, Building Codes, and Plan Sets 14.2 System Labeling and Signage Requirements 14.3 Project Closeout, Commissioning Reports, and PTO 14.4 Customer Expectations, Value Engineering, and Design Adaptation

14.2 System Labeling and Signage Requirements

Key Takeaways Explain This Topic AI

System labeling is a critical life-safety element enforced under NEC Articles 690, 705, and 706, alerting first responders and maintenance technicians to high-voltage direct current and multiple energized power sources.

NEC 110.21(B) requires field-applied warning labels to warn effectively (ANSI Z535.4 is the guide), be permanently affixed, not be handwritten, and be durable for the environment; UV-resistant engraved or UL 969-rated labels are common choices.

The 2017 NEC 690.53 label at the dc PV system disconnect lists the maximum voltage, the maximum circuit current, and, if installed, the maximum rated output current of the charge controller or dc-to-dc converter.

Rapid shutdown labels under 2017 NEC 690.56(C)(1) use a black-on-yellow title for systems that shut down the array and the conductors leaving it, and a white-on-red title for systems that shut down only the conductors leaving the array.

Last updated: October 2026

System Labeling and Signage Requirements

Photovoltaic power systems present unique electrical hazards that differ significantly from conventional alternating-current (AC) building electrical systems. Because solar arrays generate high-voltage direct-current (DC) power whenever sunlight strikes the module surface—power that cannot be shut off simply by tripping an AC circuit breaker—clear, durable, and standardized safety signage is paramount. First responders, emergency personnel, utility linemen, and service technicians rely on visible warning placards to identify energized conductors, locate isolation disconnects, understand rapid shutdown boundaries, and prevent fatal electric shock or arc-flash injuries.

1. Physical Construction and Durability Standards (ANSI Z535 & UL 969)

System labels must withstand 25 or more years of continuous outdoor environmental exposure, including intense ultraviolet (UV) radiation, freezing temperatures, windblown dust, rain, and humidity. NEC 110.21(B) requires warning labels to be permanently affixed, not handwritten (except for variable information), and durable enough for the environment, so paper labels and handwritten tape do not comply.

Material and Attachment Specifications

UL 969 (Standard for Marking and Labeling Systems): Many outdoor adhesive labels are recognized under UL 969 for exposure to weather, heat, moisture, and UV light. The NEC does not require UL 969 by name, but the label must suit the environment.

Placard Construction: High-quality installations utilize engraved phenolic plastic (two-layer micro-surfaced acrylic/phenolic where the top layer is engraved to reveal a contrasting core) or anodized metal placards (photo-anodized aluminum with sealed image layers).

Attachment Methods: While high-bond acrylic foam adhesives (such as 3M VHB) are accepted on clean, smooth, powder-coated enclosures, outdoor placards should be secured using mechanical fasteners —including stainless steel pop rivets, tamper-resistant machine screws, or UV-resistant outdoor cable ties on raceways. Fasteners prevent placards from falling off during building fires or seasonal thermal cycling.

ANSI Z535 Safety Sign Standards

NEC labeling guidelines incorporate the ANSI Z535 standards for safety signs and colors, which establish a strict hierarchy of signal words:

DANGER: Indicates an imminently hazardous situation that, if not avoided, will result in death or serious injury. Reserved for high-voltage utility switchgear or high-hazard electrical enclosures.

WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in death or serious injury. Used for PV system disconnects, energized DC circuits, and backfeed breakers.

CAUTION: Indicates a potentially hazardous situation that, if not avoided, may result in minor or moderate injury, or equipment damage. Used for operating instructions or multiple source notifications.

Visual Formatting: Signal words must appear in bold uppercase letters inside a colored header box (e.g., black text inside an orange header for WARNING; white text inside a red header for DANGER). Letters must be contrasted sharply against the background (e.g., white letters on red, or black letters on yellow or orange).

2. Main Service Disconnect and Dual Power Source Placards

When a photovoltaic system is interconnected with a premises electrical system, the building contains multiple sources of electrical power. Technicians working on service equipment must be alerted that opening the main utility breaker does not de-energize equipment backfed by the solar system.

Dual Power Source Warning (NEC 705.10 / NEC 690.54)

A permanent plaque or directory must be placed at the main service disconnect and all points of interconnection:

NEC 705.10 Directory Requirement: A permanent plaque or directory must be installed at each service equipment location denoting the presence and physical location of all electric power sources (utility grid, solar PV system, energy storage system, or standby generator) on the premises.

  • Dual Source Warning Text: WARNING: DUAL POWER SOURCES
  • SECOND SOURCE IS PHOTOVOLTAIC SYSTEM
  • DISCONNECT BOTH SOURCES BEFORE SERVICING

Point of Interconnection Identification (NEC 690.54): All interactive system points of connection with other sources must be marked at an accessible location at the disconnecting means with the rated AC output current and the nominal operating AC voltage.

PV System Disconnect (NEC 690.13(B)): Marked "PV SYSTEM DISCONNECT" or equivalent. Where the line and load terminals can both be energized in the open position, add: "WARNING – ELECTRIC SHOCK HAZARD – TERMINALS ON THE LINE AND LOAD SIDES MAY BE ENERGIZED IN THE OPEN POSITION."

ESS Disconnect (NEC 706.7(D)): Marked with the nominal ESS voltage, the maximum available short-circuit current, the clearing time or arc duration, and the date of the calculation (or an arc-flash label applied per industry practice).

3. DC PV Power Source Label (NEC 690.53)

The 2017 NEC 690.53 requires the installer to provide a permanent label for the dc PV power source at the dc PV system disconnecting means and at each dc equipment disconnecting means required by 690.15. Where a disconnect serves more than one dc PV power source, the values are listed for each source. The label shows:

Maximum Voltage: The maximum PV system voltage calculated per 690.7, corrected for the lowest expected ambient temperature.

Maximum Circuit Current: The maximum current calculated per 690.8(A), such as 125% of the sum of the parallel module short-circuit currents.

Maximum Rated Output Current of the Charge Controller or DC-to-DC Converter , if one is installed. DC PV POWER SOURCE

  • -------------------------------------------
  • MAXIMUM VOLTAGE: 462.5 V
  • MAXIMUM CIRCUIT CURRENT: 23.0 A
  • MAX RATED OUTPUT CURRENT OF CHARGE
  • CONTROLLER OR DC-DC CONVERTER: NOT USED

Edition note: The 2014 NEC 690.53 also required the rated maximum power-point current and voltage, and many older study materials still list them; the 2017 NEC dropped those values. The 2020 NEC reduced 690.53 to a maximum-voltage label, which the 2023 NEC moved to 690.7(D).

4. Rapid Shutdown Identification and Equipment Signage (NEC 690.56(C))

NEC 690.12 mandates rapid shutdown of rooftop PV systems to protect emergency responders from electric shock when operating on roofs. NEC 690.56(C) dictates standardized visual plaques to inform firefighters whether rapid shutdown controls conductors inside the array boundary:

  • Rapid Shutdown Type Labels (690.56(C)(1))
  • 690.56(C)(1)(a): Array and Conductors Leaving It Shut Down

Title in capitals at least 3/8 inch high, black on yellow ; remaining text black on white, at least 3/16 inch: SOLAR PV SYSTEM IS EQUIPPED WITH RAPID SHUTDOWN

TURN RAPID SHUTDOWN SWITCH TO THE "OFF" POSITION

TO SHUT DOWN PV SYSTEM AND REDUCE SHOCK HAZARD IN ARRAY.

690.56(C)(1)(b): Only Conductors Leaving the Array Shut Down

The same title in capitals at least 3/8 inch high, white on red ; remaining text black on white: SOLAR PV SYSTEM IS EQUIPPED WITH RAPID SHUTDOWN

TURN RAPID SHUTDOWN SWITCH TO THE "OFF" POSITION

TO SHUT DOWN CONDUCTORS OUTSIDE THE ARRAY.

CONDUCTORS IN ARRAY REMAIN ENERGIZED IN SUNLIGHT.

Both labels include a simple building diagram; the (1)(b) version shows the array area that stays energized. Where a building has PV systems with both rapid shutdown types, or one system without rapid shutdown, 690.56(C)(2) requires a roof plan showing each system, with a dotted line around the areas that remain energized after the rapid shutdown switch is operated.

Rapid Shutdown Switch Label (690.56(C)(3))

The rapid shutdown switch must have a label on it or within 3 feet (1 m) of it reading: RAPID SHUTDOWN SWITCH FOR SOLAR PV SYSTEM

The label must be reflective, with capital letters at least 3/8 inch high in white on a red background.

5. DC Raceway and Enclosure Labeling (2017 NEC 690.31(G)(3) and (G)(4))

Because dc PV circuits cannot be de-energized from the building's ac panel, firefighters cutting into walls or roofs need clear warnings. The 2017 NEC requires wiring methods and enclosures containing PV system dc circuits to be marked:

Wording: WARNING: PHOTOVOLTAIC POWER SOURCE , by permanently affixed labels or other approved permanent marking.

What Gets Marked: Exposed raceways, cable trays, and other wiring methods; covers or enclosures of pull boxes and junction boxes; and conduit bodies in which any of the available openings are unused.

Format: Labels must be visible after installation and reflective, with all capital letters at least 3/8 inch (9.5 mm) high in white on a red background , and suitable for the environment.

Spacing: Labels must appear on every section of the wiring system that is separated by enclosures, walls, partitions, ceilings, or floors, with no more than 10 feet (3 m) between labels or markings.

  • The 2020 NEC moved this rule to 690.31(D)(2) and also permits the wording "SOLAR PV DC CIRCUIT."
  • 6. Point of Interconnection Busbar Warnings and Directory Maps
  • Backfeed Breaker Warning (2017 NEC 705.12(B)(2)(3)(b))

When a solar PV system interconnects on the load side of a panelboard busbar under the 120% rule, the solar circuit breaker must be positioned at the opposite end of the busbar from the utility main breaker. Moving this breaker to the center of the panel could subject the busbar to severe localized overcurrent. To prevent this, a permanent warning label must be installed immediately adjacent to the solar backfeed breaker: WARNING: POWER SOURCE OUTPUT CONNECTION

  • DO NOT RELOCATE THIS OVERCURRENT DEVICE
  • Main Service Directory Plaque (NEC 705.10)

Every building with on-site generation requires a permanent directory plaque at the electrical service entrance. The plaque must provide a graphic site map or clear text detailing the physical location of the main service disconnect, the solar PV system disconnects, battery energy storage disconnects, and any standby generators.

7. System Labeling Specification Matrix

The following matrix summarizes the required warning labels, placards, physical characteristics, and installation locations across a code-compliant solar installation:

Subsystem / Code Section Mandatory Label Text Color Scheme (Background / Font) Physical Placement Location Durability & Fastening Specification

NEC 690.53 DC PV POWER SOURCE with maximum voltage, maximum circuit current, and converter or charge controller output current (if installed) High contrast (110.21(B)) DC PV system disconnect and each 690.15 dc equipment disconnect Engraved or UL 969-rated label, permanently affixed

NEC 690.54 PHOTOVOLTAIC SYSTEM AC DISCONNECT (Nominal Operating AC Voltage: [X] V; Rated AC Output Current: [Y] A) Red background / White text Front cover of external AC disconnect switch Engraved UV-resistant phenolic plaque, mechanically attached

NEC 690.56(C)(1)(a) SOLAR PV SYSTEM IS EQUIPPED WITH RAPID SHUTDOWN (array and conductors leaving it shut down) Title black on yellow; text black on white Service equipment or another approved readily visible location Durable outdoor-rated label or plaque

NEC 690.56(C)(3) RAPID SHUTDOWN SWITCH FOR SOLAR PV SYSTEM Reflective, white on red On or within 3 ft of the rapid shutdown switch Capital letters at least 3/8 in high

NEC 690.31(G)(3)–(4) (2017) WARNING: PHOTOVOLTAIC POWER SOURCE Reflective, white on red Every section separated by walls, floors, or enclosures, at most 10 ft apart Capital letters at least 3/8 in high, suitable for the environment

NEC 705.10 CAUTION: MULTIPLE SOURCES OF POWER (Directory map showing PV, ESS & Utility) White background / Black text, or Red / White Main service disconnect and all on-site generator disconnects Engraved phenolic plaque with high-contrast etched schematic diagram

NEC 705.12(B)(2)(3)(b) (2017) WARNING: POWER SOURCE OUTPUT CONNECTION — DO NOT RELOCATE THIS OVERCURRENT DEVICE High contrast (110.21(B)) Adjacent to the backfed breaker Durable, permanently affixed label

Loading diagram... Photovoltaic System Safety Placard and Signage Hierarchy