Study guide

7.4 Concrete Defects, Joints, and Cold-Weather Practices

NASCLA Contractor Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Coverage Map & Exam Overview

Coverage Map & Exam Overview

2 Business Organization, Licensing & Law

1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution

3 Financial Management, Tax & Labor Law

2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management

4 Estimating, Bidding & Plan Reading

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing

5 Project Management & Scheduling

4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process

6 Construction Safety & OSHA (29 CFR 1926)

5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces

7 General Requirements & Sitework

6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage

8 Concrete (CSI Division 03)

7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices

9 Masonry (CSI Division 04)

8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction

10 Metals & Wood (CSI Divisions 05 & 06)

9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths

11 Thermal & Moisture Protection (CSI Division 07)

10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers

12 Openings & Finishes (CSI Divisions 08 & 09)

11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules

13 Mechanical, Plumbing & Electrical Overview

12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code

7.4 Concrete Defects, Joints, and Cold-Weather Practices

Key Takeaways Explain This Topic AI

Match defect to cause: honeycomb=poor consolidation, scaling/dusting=finishing over bleed water, plastic shrinkage/crazing=rapid surface drying, spalling=corroding low-cover rebar.

Control (contraction) joints locate shrinkage cracks (saw-cut 1/4 the slab depth); construction joints are stop/start points; isolation joints allow independent movement.

Control-joint spacing ~2-3 times slab thickness in inches converted to feet (a 4-in slab = ~10 ft); saw-cut early before stress builds.

Cold weather (ACI 306, below 40 deg F): keep concrete above 50 deg F and protect from freezing until ~500 psi or it loses ~50% strength; never place on frozen ground.

Markup adds a percent to cost; margin is a percent of price (20% margin on $50,000 cost = $62,500 price, higher than a 20% markup price of $60,000).

Last updated: June 2026

The final concrete topic covers defects, joints, and weather practices — presented here through editorial scenarios. References include ACI 224 (cracking), ACI 306 (cold weather), and ACI 305 (hot weather). These exercises ask whether you can match a symptom to its cause and select the correct joint type .

Common defects and causes:

  • Defect Cause
  • Honeycomb Poor consolidation / oversize aggregate / segregation
  • Scaling Finishing over bleed water; no air entrainment + freeze-thaw
  • Dusting Finishing with bleed water; low cement at surface
  • Plastic shrinkage cracks Rapid surface drying (hot, windy) before set
  • Crazing Surface map-cracking from rapid surface drying
  • Spalling Corroding rebar (low cover) expanding
  • Efflorescence Soluble salts carried to surface by moisture

Trap: scaling and dusting both trace back to finishing over bleed water .

Joints control where concrete cracks and how it moves:

Control (contraction) joints: tooled or saw-cut grooves that create a weakened plane so shrinkage cracking occurs at the joint , not randomly. Cut to a depth of 1/4 the slab thickness .

Construction joints: where one placement stops and the next begins (use keyways or dowels).

Isolation (expansion) joints: full-depth separation from walls, columns, footings to allow independent movement.

Trap: a control joint does not prevent cracks — it locates them.

Worked joint numeric: Control joint spacing rule of thumb is about 24 to 36 times the slab thickness (in feet), commonly 2-3 times the slab thickness in inches = feet .

For a 4-inch slab: spacing ~ 2.5 x 4 = 10 ft maximum.

Depth of saw cut: 1/4 x 4 in = 1 in .

Trap: oversized panels or skipped joints lead to random shrinkage cracking . Saw-cut early (within hours, before shrinkage stress builds).

Cold-weather concreting (ACI 306) applies when the average daily temperature is below 40 deg F for 3+ days. Goals: keep concrete above 50 deg F during placement/curing and protect from freezing until it reaches 500 psi .

Practices:

Heat mixing water and/or aggregate.

Use Type III cement or an accelerator (non-chloride near steel).

Insulating blankets/heated enclosures.

Never place on frozen ground.

Trap: fresh concrete that freezes before ~500 psi suffers permanent strength loss (~50%).

Hot-weather concreting (ACI 305) risks rapid slump loss, plastic shrinkage cracking, and flash set above ~90 deg F.

Practices: use a retarder , cool the mix water (chipped ice), dampen subgrade and forms, place during cooler hours, fog/cure immediately.

Markup vs. margin trap (business crossover): On a $50,000 concrete job, a 20% markup = 50,000 x 0.20 = $10,000 added (price $60,000). A 20% margin means cost is 80% of price: price = 50,000 / 0.80 = $62,500 . Margin always yields a higher price than the same-percentage markup.