Study guide

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat)

NASCLA Contractor Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Coverage Map & Exam Overview

Coverage Map & Exam Overview

2 Business Organization, Licensing & Law

1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution

3 Financial Management, Tax & Labor Law

2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management

4 Estimating, Bidding & Plan Reading

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing

5 Project Management & Scheduling

4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process

6 Construction Safety & OSHA (29 CFR 1926)

5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces

7 General Requirements & Sitework

6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage

8 Concrete (CSI Division 03)

7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices

9 Masonry (CSI Division 04)

8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction

10 Metals & Wood (CSI Divisions 05 & 06)

9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths

11 Thermal & Moisture Protection (CSI Division 07)

10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers

12 Openings & Finishes (CSI Divisions 08 & 09)

11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules

13 Mechanical, Plumbing & Electrical Overview

12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat)

Key Takeaways Explain This Topic AI

Drawings show location and quantity; specifications show quality and standards, and together they form the contract documents.

Sheet discipline order runs General, Civil, Architectural, Structural, Mechanical, Plumbing, Electrical (G, C, A, S, M, P, E).

CSI MasterFormat uses a six-digit number across about 50 divisions; know Division 03 Concrete, 04 Masonry, 23 HVAC, 26 Electrical.

Never scale a drawing for a working dimension; noted dimensions govern over scaled ones and specs generally govern over drawings for quality.

The G-series sheet links drawings to IBC occupancy, construction type, and fire-rating chapters.

Last updated: June 2026

Reading Construction Drawings and Specifications

A commercial general building contractor must read a construction document set as a coordinated whole. The set has two legal parts: the drawings (graphic information) and the project manual (written specifications , the contract, and general conditions). The drawings show where and how much ; the specs show what quality and what standard . This editorial navigation section uses the listed open-book references, so know where each fact lives, not just the answer.

Sheet Organization and Discipline Order

A full set follows a standard sequence so an estimator can navigate quickly. Memorize the discipline prefixes used on sheet numbers:

  • Prefix Discipline Typical content
  • G General Cover, code analysis, symbols
  • C Civil Site grading, utilities, drainage
  • A Architectural Plans, elevations, sections, schedules
  • S Structural Foundations, framing, details
  • M Mechanical HVAC ductwork, equipment
  • P Plumbing Supply, waste, vent piping
  • E Electrical Power, lighting, panel schedules

The set typically reads G, C, A, S, M, P, E (sometimes adding FP for fire protection).

Drawing Scales and Detail Hierarchy

Drawings move from large views to small details. Common architectural scales: floor plans at 1/8" = 1'-0" , wall sections at 3/4" = 1'-0" , and details at 1-1/2" = 1'-0" or 3" = 1'-0" . Civil and site plans often use engineer scales such as 1" = 20' or 1" = 50' .

A common practical mistake: never scale a drawing to get a dimension. Always use the written dimension or the dimension string. Scaling is only a rough check because printing and reproduction distort the sheet.

CSI MasterFormat Specification Numbering

The Construction Specifications Institute (CSI) MasterFormat organizes the project manual into numbered divisions . The 2004-and-later format uses a six-digit numbering system (e.g., 03 30 00) across roughly 50 divisions . The general contractor must know the core divisions:

  • Division Title
  • 01 General Requirements
  • 03 Concrete
  • 04 Masonry
  • 05 Metals
  • 06 Wood, Plastics, and Composites
  • 07 Thermal and Moisture Protection
  • 08 Openings (Doors and Windows)
  • 09 Finishes
  • 22 Plumbing
  • 23 HVAC
  • 26 Electrical

Note the post-2004 shift: HVAC and Electrical moved out of old Division 15/16 into the 20s and 26 .

Specification Format and Order of Precedence

Each section follows the CSI three-part SectionFormat : Part 1 General (submittals, references), Part 2 Products (materials, ASTM standards), and Part 3 Execution (installation, tolerances). When documents conflict, most contracts set an order of precedence : the specifications usually govern over the drawings for materials and quality, while noted dimensions govern over scaled dimensions and larger-scale details govern over smaller-scale plans . Always read the contract's precedence clause.

Code Cross-References on the Drawings

The G-series code-analysis sheet ties drawings to the International Building Code (IBC) : occupancy classification (IBC Chapter 3), construction type (IBC Chapter 6, Types I-V), allowable area and height (IBC Chapter 5), and fire-resistance ratings (IBC Chapter 7). Specs reference consensus standards directly, for example ASTM C90 for load-bearing concrete masonry units or ASTM A615 for reinforcing steel. Verifying these references is core open-book skill.