Study guide

12.2 HVAC Systems and Load Concepts

NASCLA Contractor Study Guide Exam

Track your progress as you read

Finished sections get a check mark.

1 Coverage Map & Exam Overview

Coverage Map & Exam Overview

2 Business Organization, Licensing & Law

1.1 Business Entity Types and Formation 1.2 NASCLA Trade-Exam Waiver and Agency Licensing Boundaries 1.3 Construction Contract Law and Types of Contracts 1.4 Lien Law, Bond Claims, and Dispute Resolution

3 Financial Management, Tax & Labor Law

2.1 Financial Statements, Job Costing, and Cash Flow 2.2 Payroll, Federal/State Tax, and Recordkeeping 2.3 Labor & Employment Law (FLSA, immigration/I-9, EEO) 2.4 Insurance, Surety Bonds, and Risk Management

4 Estimating, Bidding & Plan Reading

3.1 Reading Construction Drawings and Specifications (CSI MasterFormat) 3.2 Quantity Takeoff and Material Estimating 3.3 Bidding, Markup, Overhead, and Profit 3.4 Change Orders, Allowances, and Unit Pricing

5 Project Management & Scheduling

4.1 Project Delivery Methods and the Submittal/RFI Process 4.2 Scheduling (CPM, Bar Charts, Critical Path) 4.3 Quality Control, Inspections, and Closeout 4.4 Permits, Codes, and the Inspection Process

6 Construction Safety & OSHA (29 CFR 1926)

5.1 OSHA Administration, Recordkeeping, and the General Duty Clause 5.2 Fall Protection, Scaffolds, and Ladders 5.3 Excavation/Trenching, Electrical, and Hazard Communication 5.4 PPE, Fire Protection, Cranes, and Confined Spaces

7 General Requirements & Sitework

6.1 Division 01 General Requirements and Temporary Facilities 6.2 Surveying, Site Layout, and Excavation 6.3 Soils, Compaction, and Erosion/Sediment Control 6.4 Foundations, Footings, and Site Drainage

8 Concrete (CSI Division 03)

7.1 Concrete Materials, Mix Design, and Water-Cement Ratio 7.2 Formwork and Reinforcement Placement 7.3 Placing, Finishing, Curing, and Testing (slump, cylinders) 7.4 Concrete Defects, Joints, and Cold-Weather Practices

9 Masonry (CSI Division 04)

8.1 Masonry Units, Mortar Types (M/S/N/O), and Grout 8.2 Brick and CMU Bonds, Reinforcement, and Coursing 8.3 Lintels, Control/Expansion Joints, and Flashing 8.4 Masonry Estimating and Cold/Hot Weather Construction

10 Metals & Wood (CSI Divisions 05 & 06)

9.1 Structural Steel, Connections, and Welding/Bolting 9.2 Light-Gauge Metal Framing 9.3 Wood Framing, Species/Grades, and Fasteners 9.4 Engineered Wood, Trusses, and Load Paths

11 Thermal & Moisture Protection (CSI Division 07)

10.1 Waterproofing, Dampproofing, and Below-Grade Protection 10.2 Insulation, R-Values, and Vapor Barriers 10.3 Roofing Systems (steep-slope and low-slope) and Underlayment 10.4 Flashing, Sealants, and Air Barriers

12 Openings & Finishes (CSI Divisions 08 & 09)

11.1 Doors, Windows, Glazing, and Hardware 11.2 Gypsum Board, Plaster, and Framing 11.3 Flooring, Tile, and Acoustical Ceilings 11.4 Painting, Coatings, and Finish Schedules

13 Mechanical, Plumbing & Electrical Overview

12.1 Plumbing Systems, Fixtures, and DWV/Supply Basics 12.2 HVAC Systems and Load Concepts 12.3 Electrical Systems, Service, and NEC Basics 12.4 Coordination, Rough-In, and Energy Code

12.2 HVAC Systems and Load Concepts

Key Takeaways Explain This Topic AI

One ton of cooling equals 12,000 BTU/h; light commercial runs roughly 400 to 600 square feet per ton as a sanity check only.

Packaged rooftop units dominate light commercial; efficiency is rated by SEER2 (cooling) and AFUE (gas heating).

Oversizing causes short-cycling and poor dehumidification, so a stamped Manual J / ASHRAE load calc governs sizing.

ASHRAE 62.1 sets outdoor-air ventilation; the IFGC sets combustion air at about 50 cubic feet of room volume per 1,000 BTU/h.

GC must verify condensate primary plus overflow drains, fire/smoke dampers at rated assemblies, and roof load for the RTU.

Last updated: June 2026

HVAC Systems and Load Concepts

Heating, ventilation, and air conditioning (HVAC) is governed by the International Mechanical Code (IMC) for equipment and ductwork, the International Fuel Gas Code (IFGC) for gas-fired appliances, and ASHRAE Standard 62.1 for ventilation rates. As the general contractor (GC) , you coordinate the mechanical subcontractor's rough-in, verify clearances and combustion air, and confirm the design meets the International Energy Conservation Code (IECC) . Capacity is measured in British thermal units per hour (BTU/h) and cooling in tons , where 1 ton equals 12,000 BTU/h .

System Types

  • System Description Typical use
  • Split system Outdoor condenser plus indoor air handler Small commercial, retail
  • Packaged rooftop unit (RTU) All-in-one on the roof Strip malls, big-box
  • Variable refrigerant flow (VRF) Multiple indoor units, one outdoor Offices, mixed zones
  • Hydronic (boiler/chiller) Heated/chilled water to coils Large institutional

Rooftop units (RTUs) dominate light commercial because they save interior space and simplify roof-curb installation. Efficiency is rated by SEER2 (cooling) and AFUE (gas furnace heating, expressed as a percentage); the GC must confirm the installed unit meets the energy-code minimum on the mechanical schedule.

Load Calculation Basics

Sizing is done with a Manual J style load calculation (commercial uses ASHRAE methods), accounting for envelope conductance, glazing, occupancy, lighting, and infiltration. Practice check: oversizing a unit causes it to short-cycle , fail to dehumidify, and waste energy. A rule-of-thumb check (never a substitute for a real calc) is roughly 400 to 600 square feet per ton in light commercial.

Worked example: A 6,000-square-foot retail space at 500 square feet per ton needs about 12 tons of cooling, or 12 x 12,000 = 144,000 BTU/h . Always verify with the engineer's stamped load; the rule of thumb is only a sanity check on the takeoff.

Ventilation and Combustion Air

ASHRAE 62.1 sets outdoor-air ventilation by people and floor area; an office is roughly 5 cubic feet per minute (cfm) per person plus 0.06 cfm per square foot . Gas appliances need combustion air per the IFGC — the old benchmark is 50 cubic feet of room volume per 1,000 BTU/h of input for indoor confined spaces, or dedicated combustion-air openings. Ducts must be sealed and, in unconditioned space, insulated to the IECC R-value (commonly R-6 to R-8 ). Flexible duct runs are length-limited to control static pressure and airflow loss.

Duct Sizing and Airflow

Airflow is measured in cubic feet per minute (cfm) , and a common design benchmark is 400 cfm per ton of cooling. A 5-ton unit therefore moves about 2,000 cfm . Ducts are sized to hold velocity and friction in range (often around 0.08 to 0.1 inch of water column per 100 feet of friction loss in light commercial).

Undersized ducts raise static pressure, cut airflow, and make the equipment work harder — an efficiency trap the energy code targets. Supply registers, return grilles, and balancing dampers let the test-and-balance (TAB) contractor tune each zone to the design cfm so no room is starved or over-pressurized.

Coordination and Practice Checks

The GC sequences HVAC after structure and before ceilings close: set roof curbs, install ductwork in the ceiling plenum, then grilles after the grid. Watch clearance to combustibles on flues and condensate drainage — every cooling coil needs a primary drain plus a secondary/overflow provision per the IMC.

A frequent trap: forgetting that return air cannot be drawn from a space containing fuel-fired equipment in certain configurations, and that fire/smoke dampers are required where ducts cross rated assemblies. Confirm the roof structure carries the RTU dead load with the structural engineer.

Also remember OSHA 29 CFR 1926 Subpart M fall protection at 6 feet governs workers setting rooftop units, and crane lifts of RTUs invoke Subpart CC crane rules.